Stacking Kit Instruction

ManualsBrandsPerlick ManualsWine Refrigerators and Beverage CentersPerlick C-Series 24" Stainless Steel Solid Door Left Hinge Indoor Beverage Center

RELEASE FOR PRODUCTION

3/12/2014 JMP

REVISIONS

Milwaukee, WI 53223

DRAWN

Perlick Corporation

95220

JMP 3/12/2014

SCALE

1:5

DATE

THIS DOCUMENT/PUBLICATION/SOFTWARE/DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM, ELECTRONIC

OR MECHANICAL, INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANYINFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK CORPORATION

48" Mounting Plate

Grill

DRILL

5/32" DRILL BIT

STACKING KIT INSTALLATION

Tools Required

with the cabinet. Never install if used

with caster kits or extended leg kits.

IMPORTANT

For built-in applications only! Ensure

the anti-tip brackets are installed per

the installation manual that came

Phillips

Screwdriver

#10 x 1/2" Sheet Metal Screw

1/4-20 x 1/2" Machine Screw

Grill Mounting Bracket

15" & 24" Mounting Plate

Latch

Latch Strike

Bumper, Adhesive Poly

HP48

Part Number Description

Left Hinged

Door

Right

Hinged Door

Left Hinged

Door

Right

Hinged Door

Left Hinged

Door

Right

Hinged Door

Left & Right

Hinged Door

69608-1 15" Grill, Left Hinged Door 1 - - - - - -

69609-1 15" Grill, Right Hinged Door - 1 - - - - -

68837 15" Grill Mounting Bracket 1 1 - - - - -

69603-1 24" Grill, Left Hinged Door - - 1 - 1 - 1

69604-1 24" Grill, Right Hinged Door - - - 1 - 1 1

68836 24" Grill Mounting Bracket - - 1 1 1 1 2

68094-15 15" Mounting Plate 1 1 - - - - -

68094-24 24" Mounting Plate - - 1 1 - - -

68094-24x18 24" x 18" Mounting Plate - - - - 1 1 -

68094-48 48" Mounting Plate - - - - - - 1

63965 Latch Strike 2 2 2 2 2 2 4

63966 Latch 2 2 2 2 2 2 4

C31323 Bumper, Adjesive Poly 4 4 4 4 4 4 8

M00885-189 1/4-20 x 1/2" Machine Screw 4 4 4 4 4 4 6

M50050-466 #10 x 1/2" Sheet Metal Screw 4 4 4 4 4 4 11

HP15 HP24, HC24, & HA24 HH24

Parts Required

Summary of content (5 pages)

PAGE 1
STACKING KIT INSTALLATION Tools Required IMPORTANT For built-in applications only! Ensure the anti-tip brackets are installed per the installation manual that came with the cabinet. Never install if used with caster kits or extended leg kits.
PAGE 2
STACKING KIT INSTALLATION CAUTION: These cabinets are extremely heavy. Ensure that you have enough people on hand to help in repositioning the units so that it can be done safely and without damage. Step 1: Drill out top row of rivets along back of the bottom cabinet using a 5/32" drill bit. 2 rivets on 24" & 15" wide cabinets 5 rivets on 48" wide cabinet Step 2: Lay upper cabinet on its back and remove leg levelers and grill(s) from unit. Remove 2 additional leg levelers from 48" upper units.
PAGE 3
STACKING KIT INSTALLATION Step 3: Attach mounting plate(where the leg levelers were removed in step 2) by using 1/4-20 machine screws. Flange should be pointing away from the bottom of the unit. Bottom of cabinet Flange Back of cabinet Step 4: Place upper unit on top of lower unit and attach using #10 sheet metal screws (where the rivets were drilled out in step 1). Note: To prevent damage to the compressor, wait 24 hours before powering on unit after turning the cabinet back to its upright position.
PAGE 4
STACKING KIT INSTALLATION Step 5: Remove (2) #10 sheet metal screws from the front of the top cabinet (These screws will be used to attach the mounting bracket) Attach mounting bracket(s) to the front of the cabinet using #10 sheet metal screws. Install latches into the grill bracket(s). Remove (2) screws from front of cabinet. Attach grill mounting brackets using #10 sheet metal screws. Install latches to grill mounting bracket.
PAGE 5
STACKING KIT INSTALLATION Step 6: Attach (4) bumpers and (2) latch strikes to each new grill. Orient the tabs on the latch strike vertically. Attach grill assembly to upper unit. Move stacked assembly into final position by pushing lower unit. This edge vertical. Bumper Note: When using stacking kit to join (2) HH24 or HA24 units, a wall mount anti-tip kit must be installed. See cabinet installation manual for instructions.