Stacking Kit Installation

ManualsBrandsPerlick Manuals25 Bottles and UnderShallow Depth Series Built-In Wine Cooler

Table Of Contents

95010

8300 W. Good Hope Rd. Milwaukee, WI 53223 Phone: (414)353-7060 Fax: (414)-353-7069 perlick.com

Perlick is comitted to continuous improvement. Therefore, we reserve the right to change specifications without warning

5/32" Drill Bit

LATCH STRIKE

Grille

15" & 24" Mounting Plate

Phillips

Screwdriver

48" & 72" Mounting Plate

BUMPER, ADHESIVE POLY

#10 X 1/2" SHEET METAL SCREW

-1-

95010 REV C

Tools Required

IMPORTANT

For built-in applications only!

Ensure the anti-tip brackets are installed

per the installation and operating

manual that came with the cabinet.

Never install if used with caster kits or

1/4-20 X 1/2" MACHINE SCREW

extended leg kits.

Parts Required

MODEL

Part Number Description HP15

HP24 &

HC24

HH24 &

HC24-18

HP48 HP72

63965 LATCH STRIKE 2 2 2 4 6

65700-2 15" Grille 1

65733-4 24" Grille 1 1 2 3

68094-15 15" Mounting Plate 1

68094-24 24" Mounting Plate 1

68094-24x18 24"x18" Mounting Plate 1

68094-48 48" Mounting Plate 1

68094-72 72" Mounting Plate 1

C31323 Bumper, Adhesive Poly 4 4 4 8 12

M00885-189

1/4-20 X 1/2" MACHINE

SCREW

4 4 4 6 6

M50050-466

#10 X 1/2" SHEET METAL

SCREW

2 2 2 5 5

STACKING KIT INSTALLATION

Drill

Summary of content (4 pages)

PAGE 1
STACKING KIT INSTALLATION IMPORTANT For built-in applications only! Ensure the anti-tip brackets are installed per the installation and operating manual that came with the cabinet. Never install if used with caster kits or extended leg kits.
PAGE 2
STACKING KIT INSTALLATION These cabinets are extremely heavy. Ensure that you have CAUTION: enough people on hand to help in repositioning of the units so that it can be done safely and without damage. Step 1: Drill out top row of rivets along back of the bottom cabinet using 5/32" drill bit. 2 rivets on 24 and 15 inch wide cabinets. 5 rivets on 48 and 72 inch wide cabinets. Back View Back View Step 2: Lay upper cabinet on its back and remove leg levelers and grille(s) from unit.
PAGE 3
STACKING KIT INSTALLATION Step 3: Attach mounting plate (where the leg levelers were removed in step 2) by using 1/4-20 machine screws . Flange should be pointing away from the bottom of the unit. Bottom of cabinet Flange Step 4: Place upper unit on top of lower unit and attach using #10 sheet metal screws (where the rivets were drilled out in step 1). 7 68 8 " NOTE: EXTENSION OF LEG LEVELERS WILL INCREASE ASSEMBLY HEIGHT 8300 W. Good Hope Rd.
PAGE 4
STACKING KIT INSTALLATION Step 5: Attach -4- bumpers and -2- latch strikes to each new grille. Orient tabs vertically. Attach grille assemby to upper unit. Move stacked assembly into final position by pushing lower unit. This edge vertical. Bumper Note:When using stacking kit to join -2- HH24 or HC24-18 units, a wall mount anti-tip kit must be installed. See cabinet manual for instructions. 8300 W. Good Hope Rd. Milwaukee, WI 53223 Phone: (414)353-7060 Fax: (414)-353-7069 perlick.