User's Manual

ManualsBrandsPerlick ManualsWebcamPerlick Perlick DC Series Concessionaire Portable Dispensers DC96S

Form No. Z2283

Rev. 06.14.10

INSTALLATION AND OPERATION INSTRUCTIONS

CONCESSIONAIRE PORTABLE DISPENSERS

Table of Contents

Preparing the Cabinet for Use

Specifications ........................................................2

List of Included Parts ............................................3

Tools Required.......................................................3

Plumbing ...............................................................3

Electrical ................................................................3

Installing Casters ...................................................3

Tapping

Connecting the Keg Coupler.................................4

Tapping the Keg ....................................................4

Connecting the Regulator .....................................5

Adjusting Gas Flow ...............................................5

CO2 Leak Test .......................................................5

Replacing a CO2 Gas Cylinder..............................5

Handling CO2 Gas .................................................5

Temperature

Beer Temperature ..................................................6

Cleaning

Cleaning the Beer Lines ........................................7

Cleaning the Cabinet .............................................7

General Information

How to Pour a Perfect Glass of Beer ...................8

Troubleshooting .....................................................9

Beer Facts .............................................................9

Replacement Parts ........................................ 10-11

Wiring Diagram ....................................................12

8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069

Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com

IMPORTANT INFORMATION

To register your product, visit our web site at

(www.perlick.com). Click on “Commercial”, then

“Service”. You will see the link to “Warranty

Registration Form”. You must complete and submit

this form or the installation date will revert back to

the ship Date.

This manual has been prepared to assist you in the

installation of your Concessionaire Dispenser and to

acquaint you with its operation and maintenance.

We dedicate considerable time to ensure that our

products provide the highest level of customer

satisfaction. If service is required, your dealer can

provide you with a list of qualified service agents.

For your own protection, never return merchandise

for credit without our approval.

We thank you for selecting a Perlick product and

assure you of our continuing interest in your

satisfaction.

WARNING: When lifting, the full weight of the

cabinet must be supported. Lift from the cabinet

base and not from the top. Improper lifting can

result in severe damage to the cabinet.

MODEL NOS.

DC Series

Summary of content (12 pages)

PAGE 1
INSTALLATION and OPERATION INSTRUCTIONS Concessionaire Portable Dispensers MODEL NOS. DC Series IMPORTANT INFORMATION To register your product, visit our web site at (www.perlick.com). Click on “Commercial”, then “Service”. You will see the link to “Warranty Registration Form”. You must complete and submit this form or the installation date will revert back to the ship Date.
PAGE 2
Installation and Operating Instructions Sizes and Specifications, Concessionaire Dispensers Model Nos. DC72S DC84S DC96S keg capacity 2 Keg 3 Keg 4 Keg CABINET Length Ins. (mm) 72” (1829) 84” (2134) 96” (2438) Dimensions Depth Ins. (mm) 243/4” (629) 243/4” (629) 243/4” (629) w/o Bumpers Height Ins. (mm) 341/2” (876) 341/2” (876) 341/2” (876) No. of dispensing heads 1 1 2 No. faucets 2 2 2 1/4 1/3 1/3 condenser unit h.p. running load - amps 5.9 7.5 7.5 Ship wt lbs.
PAGE 3
Preparing the Cabinet for Use – Concessionaire Dispensers Parts List ■ ■ ■ ■ ■ ■ ■ Plumbing Connect drain tube from drainer into dump tank. Faucet Standard. Faucet Head Assembly Caster Set. Black Connector Hose 3⁄16” x 3’. 5 ⁄16” Air Hose. Spanner Wrench. Bag of Miscellaneous Parts. Electrical The cabinet must be connected to a separately fused power source (see electrical specification plate) and grounded in accordance with National and Local Electrical Codes.
PAGE 4
Installation and Tapping – Concessionaire Dispensers Connecting the Keg Coupler (when Supplied by Perlick) ■ ■ ■ ■ Tapping a Single Valve Keg (Sankey) Place one brown leather washer into black beer line connector hose on hex nut side. Screw connector to stainless steel beverage line on faucet standard. Tighten with a wrench, but do not over tighten. Make sure lever handle on the keg coupler is in the UP (untapped) position.
PAGE 5
Installation and Tapping – Concessionaire Dispensers Connecting the Regulator to the CO2 Cylinder ■ ■ ■ Replacing CO2 Gas Cylinder ■ Remove blue plug from regulator fitting. (Note: Do not remove the carbonic washer). Screw regulator onto gas cylinder valve. Tighten with wrench until vertically straight. Be sure that shut-off valve (black lever) on regulator is in the OFF (horizontal) position. Place a screw clamp over end of red air line and push onto regulator tailpiece.
PAGE 6
Draft Beer Information – Concessionaire Dispensers Temperature One of the most common causes of dispensing problems is improper temperature. Draft beer should be stored at a temperature between 32° and 38°. At warmer temperatures, beer will foam. At temperatures lower than 30° F., beer will freeze. When beer freezes, the alcohol in the beer may separate and cause the beer to be cloudy with an “off” taste.
PAGE 7
Cleaning the Beer System – Concessionaire Dispensers The entire beer system, to include the faucet, flexible beer line and tapping devices must be cleaned at regular intervals. We recommend flushing the entire system with fresh water immediately after a keg has been emptied. Once each month the system should be cleaned chemically. ■ It is recommended that you purchase Perlick’s Pump Type Cleaning Kit.
PAGE 8
Pouring a Perfect Glass of Beer – Concessionaire Dispensers Step 1 Start with a clean glass. Place the glass at a 45° angle, one inch below faucet. Do not let the glass touch the faucet. Open the faucet all the way. Step 2 After the glass has reached half full, gradually bring the glass to the upright position Step 3 Let the remaining beer run straight down the middle of the glass. This ensures proper release of CO2 by producing a 3⁄4” to 1” foam head. Step 4 Close the faucet quickly and completely.
PAGE 9
Trouble Shooting – Concessionaire Dispensers Beer Service Problems ■ ■ Cloudy Beer: Beer in glass appears hazy, not clear. Wild Beer: Dispensed beer has either too much foam or is all foam. Causes: ■ ■ ■ ■ ■ Causes: ■ Beer has been dispensed improperly. Solution: See pouring instructions on page 8. ■ Regulator pressure is set too high. ■ Warm keg temperature. Solution: Keg must be colder than 40°. Target temperature is between 36° and 38° F.
PAGE 10
Replacement Parts – Concessionaire Dispensers MODEL NOS. DC72S DC84S DC96S Condensing Units Condensing unit 115 volt, 60 hz.
PAGE 11
Replacement Parts – Concessionaire Dispensers For Single Valve Keg Coupler (Series D) 14 4 Item Part No. No. Description 1..............32499................ Probe assembly 2.............F40184............... Probe body 3...........31080-2P............. Ball 4............ 43641-1.............. Ball retainer 5...........31087-2P............. Probe washer 6..............31089................ “O” Ring - 3-per assembly 7..............43061................ Body 8...........23682-2P.....
PAGE 12
Reversing Door Hinge Tools Required ■ ■ ■ STEP 8: Re-assemble hinge brackets to unit. Bottom right bracket is assembled as the top left bracket. Top right bracket is assembled as the bottom left bracket. #3 Phillips Screwdriver. 1/16” Allen Wrench. Flathead Screwdriver Right Hinged Door (as shipped from factory) STEP 9: Re-insert top hinge pin.