Use and Care Manual

GENERAL DESCRIPTION
FEATURES AND BENEFITS
PRODUCT DATA
PERMA-CRETE
®
Features Benefits
Seals Concrete Minimizes moisture damage
Hot Tire Resistance Minimize staining and discoloration on traffic surface
Fast Drying Turns jobs quickly
Moisture and Chemical Resistance Helps to extend substrate life
Good Adhesion Resists peeling and cracking
Excellent Application Properties Reduces application time and resists pinholing
UV Resistance Extends newly painted look
Application to 35ºF (2ºC) Extends painting season
RECOMMENDED SUBSTRATES
Perma-Crete Color Seal WB Interior/Exterior Concrete Stain is a film
forming, tintable, water borne, acrylic concrete stain ideal for use on
interior/exterior, above-ground, vertical and horizontal surfaces. This
fast drying stain is water and chemical resistant. Perma-Crete Color
Seal WB Stain has excellent hot tire resistance while providing good
adhesion. This low odor product seals the surface and improves the
appearance of the substrate by adding color and durability. Perma-
Crete Color Seal WB Stain is ideal for use on concrete surfaces such
as garage floors, driveways, pool decks, walkways, patios, porches,
warehouse floors and more.
PRODUCT TYPE: 100% Acrylic
SHEEN: Satin (depending on number of coats
and porosity of substrate)
VOLUME SOLIDS*: 29% +/- 2%
WEIGHT SOLIDS*: 40% +/- 2%
WEIGHT/GALLON*: 9.8 lbs. (3.9 kg) +/- 0.2 lbs. (91 g)
VOC: <100 g/L (0.8 lbs./gal.)
*Product data calculated on product 4-4210XI.
COVERAGE: 250 to 350 sq. ft. (23 to 33 sq. meters) per US gal.
(3.78L)
Wet Film Thickness: 4.6 mils to 6.4 mils
Wet Microns: 117 to 163
Dry Film Thickness: 1.3 mils to 1.9 mils
Dry Microns: 33 to 48
Coverage figures do not include spray loss, loss due to surface irregu-
larities and porosity, nor material loss when mixing.
DRYING TIME: Dry time @ 77ºF (25ºC); 50% relative humidity.
To Touch: 30 minutes
To Recoat: 6 hours
For Pedestrian Traffic 24 hours
For Vehicular Traffic 72 hours
Drying times listed may vary depending on temperature, humidity, film
build, color, and air movement.
CLEANUP: Clean tools and hands immediately with warm, soapywa-
ter.
DISPOSAL: Contact your local environmental regulatory agency for
guidance on disposal of unused product. Do not pour down a drain or
storm sewer.
FLASH POINT: Over 200ºF (93ºC)
4-4210XI Series
CONFORMANCE STANDARDS
VOC compliant in all regulated areas
Brick Exposed Aggregate
Concrete Masonry
Concrete Block (CMU) Stucco
Read Label and Safety Data Sheet Prior to Use. See other cautions on last page.
4-4210XI
PERFORMANCE DATA
Property Test Method Results
Hot Tire Koehler I.C. Passes, no staining or adhesion loss
Water repellency ASTM D4446 Passes, no water absorption
Weathering ASTM D4587 Passes, QUV 500 Hours
Adhesion ASTM D3359 Passes, Wet and Dry
Yellowing ASTM E313 Passes, no discoloration
TINTING AND BASE INFORMATION
4-4210XI White & Pastel Base
4-4220XI Midtone Base*
4-4240XI Ultra Deep Base*
*Must be tinted before use.
Refer to the appropriate color formula book, automatic tinting equip-
ment, and or computer color matching system for color formulas and
tinting instructions.
Architectural Coatings Perma-Crete COLOR SEAL™ WB Interior/Exterior Concrete Stain