Permasteel 80QT Cooler Use & Care Guide Model number: PS-207, PS-207-80PE Thank you for purchasing your new patio cooler from Permasteel. We hope you enjoy your product. If you have any questions, please call us 1-888-287-0735 or visit www.permasteel.
Table of content Important Information Important Information 2 Parts List 3 Thank you for your purchase of our Patio Cooler. We sincerely hope you will enjoy using our fine products. Hardware 4 • Assembly Steps 5 Please take time to read these instructions thoroughly and follow each step carefully for safe and easy operation. Care & Maintenance 11 • Please contact our customer service at 1-888-287-0735 if you have any questions.
Parts List Key Description Qty A Lid Knob 2 B Lid 1 C Body Handle 2 D Body (Basin) 1 E Bottle Opener 1 F Bottle Cap Catcher 1 G Leg Frame 2 H Bottom Shelf 1 I Caster 2 J Caster with Brake 2 AA M6 x 13 Bolt 22 BB M6 x 15 Shoulder Bolt 2 CC M4 x 32 Screw 2 DD Flat Washer 4 EE Hex Nut 2 If you are missing any parts or have damaged parts, please call 1-888-287-0735 M-F 8:00-5:00 Pacific Time. For replacement, visit us at www.permasteel.
Hardware The following hardware is provided in a poly bag.
Assemble Steps Step 1 • Turn body (basin) upside down, place it on a clean, soft surface and attach 2 leg frames (G) to body (D) with (6) M6x13mm bolts (AA), 3 bolts for each leg frame, with the provided Allen wrench. Note: Do not fully tighten the bolts. Leg frames should be loose so that it can be aligned with the holes on the bottom shelf.
Step 2: • Attach the bottom shelf (H) to the leg frames (G) with (2) M6x13mm bolts (AA), (4) flat washers (DD), and (2) hex nut (EE) with the provided hex wrench. Note: Do not fully tighten the bolts. Leg frames and bottom shelf should be loose so that it can be aligned with the holes for the casters.
Step 3 • • Insert and thread casters (I) through the bottom panel holes and into leg frame using the provided open end wrench. Insert and thread casters (J) through the bottom panel holes and into other leg frame using the provided open end wrench. Note: Leg frames and bottom shelf should be loose so that it can be aligned with the holes for the casters. • Now, tighten all the bolts left loose from step 1 & 2.
Step 4 • Attach the body handles (C) to body (D) using (12) M6x13mm bolts (AA), 6 bolts for each handle, and tighten with the provided Allen wrench.
Step 5 • • Attach the bottle opener (E) to body (D) using (2) M6x13mm bolts (AA) and tighten with the Allen wrench. Attach the cap catcher (F) to body (D) using (2) M6x15mm shoulder bolts (BB).
Step 6 • • 10 Note: The lid knobs (A) are pre-attached to the lid (B). They are upside down. Please remove the knobs using a Phillips head screwdriver and re-assemble them on the lid right-side up.
Care & Maintenance Manufacturer recommends the following care & maintenance: • Cooler must be drained of water and completely dried in and out with a soft-clean cloth after every use. • When cooler is not in use for prolonged periods, it is recommended to store it in an enclosed dry place such as a storage shed or garage. • During the season when cooler is frequently used, it is recommended to use a weather-proof cover to cover when not in use.
We hope you enjoy your product and we are always here for you: Visit us at: www.permasteel.life Customer Service: 1-888-287-0735 Email: service@permasteel.life Distributed by Permasteel Inc.
