Specification Sheet

Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex


Ultra Disc
Brake Caliper Lube
AAM Revised 12/05
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
PRODUCT DESCRIPTION S.I.N.: 834-300
Permatex

Ultra Disc Brake Caliper Lube is a green,
environmentally friendly, non-melting, pure synthetic lubricant.
It is formulated to lubricate under the most adverse brake
conditions, assuring that critical caliper pins, sleeves, bushings
and pistons remain lubricated throughout pad life. Permatex

Ultra Disc Brake Caliper Lube, that is water and corrosion
resistant properties, is excellent on rolling and sliding surfaces
operating in wet or dry conditions from -40°F to +400°F. It is
compatible with internal and external brake rubber and plastic
hardware, including ethylene-propylene rubber.
PRODUCT BENEFITS
• Prevents disc brake squealing
• Prevents long bolt and sleeve seizing and galling
• Outperforms ordinary caliper grease and traditional disc
brake quiet
• Non-silicone, non-petroleum based formula
• Pure synthetic lubricant, environmentally safe
TYPICAL APPLICATIONS
• Long and short bolts
• Sleeves
• Bushings
• Outboard pad backing plate
• Inboard pad backing plate
• Disc brake calipers
• Caliper pins
• Pistons
DIRECTIONS FOR USE
1. Wirebrush the caliper housing and anchor plate to
remove all dirt and dust.
2. Apply Permatex

Ultra Disc Brake Caliper Lube to all
moving caliper hardware, mating surfaces and steel
backing plates of the disc brake pads.
3. Any excess grease that squeezes out from the mating
surfaces should be removed.
Note: Keep lubricant off pads and rotors.
PROPERTIES OF UNCURED MATERIAL
Typical Value
Chemical Type Synthetic oil
Appearance Green liquid
Specific Gravity 0.85
Worked penetration (60 strokes),
ASTM D-217 285
Dropping point, ºC (ºF) ASTM D-2265 None
Corrosion (100 hrs. 5% Salt Spray)
ASTM B-117 No rust
Timken OK Load, lbs., ASTM D-2509 40
Four-Ball Wear Scar, mm (40 kg. 1 hr.
1200 rpm) ASTM D-2266 0.6
Conradson Carbon %, ASTM D-189 0.00
Water Washout @ 100 ºF, %
ASTM D-1264 5
Pour point, ºF, ASTM D-97 -30
Rust preventive rating, ASTM D-130 1a
Flash Point, ASTM D-92, COC, °F
500
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
ORDERING INFORMATION
Part Number Container Size
20353 2 oz. tube with nozzle
20356 14g (2-7g pouches)
24110 8 oz. brush top bottle
09177 5 g pouches, display boxed
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8°
to 28°C
(46°
to 82°F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.