Specification Sheet

Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex



PermaPoxy

 Clear
General Purpose Epoxy Products
AAM Revised 02/09
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
PRODUCT DESCRIPTION
Permatex

PermaPoxy products are two part, clear epoxy
adhesive systems. PermaPoxy Clear General Purpose
epoxies are of a maximum strength formula that is available in
several working times. PermaPoxy is ideal for complex,
multi-piece assemblies. They are water and solvent resistant
and available in dual syringes or tubes.
PRODUCT BENEFITS
• Will not shrink
• Various curing cycles
• No clamping needed
• Fills gaps
• Nearly colorless
• Impact resistant
• Water resistant
TYPICAL APPLICATIONS
To bond rigid materials including:
• Chrome
• Fiberglass
• Glass
• Plastic
• Metal
DIRECTIONS FOR USE
1. Protect work area from accidental spills.
2. Surface must be clean, dry and free of grease & oil.
3. Roughen surfaces with sandpaper or other abrasives.
4. Use a sharp blade to cut off the tips of both nozzles.
5. Depress plunger on syringe or squeeze out of tubes
equal amounts of resin and hardener from tubes.
Thoroughly mix resin and hardener on a clean
discardable surface for at least one (1) minute (20 to 25
seconds in the case of the one minute epoxy) or until
uniform in color.
6. Apply to surfaces being repaired. Assemble parts
immediately. Remove excess epoxy immediately.
7. Allow bond to set for the fixture time before moving.
DIRECTIONS FOR SINGLE USE POUCH
1. Protect work area from accidental spills.
2. Surface must be clean, dry and free of grease & oil.
3. Roughen surfaces with sandpaper or other abrasives.
4. Hold the lower half of pouch between thumbs and
forefingers and press firmly to break inner seal.
5. Quickly and thoroughly mix until the blue color turns clear
(about 15 seconds).
6. Tear open pouch and apply small amount of mixture to
both surfaces and assemble parts immediately (product
sets up in about 60 seconds).
7. Remove excess epoxy immediately with mineral spirits or
acetone.
8. Usable strength is reached in 4 hours at 72ºF (22ºC).
Cooler temperatures may require a longer set time
NOTE:
Adhesive will not bond most polyethylene or
polypropylene plastics.
For Cleanup
1. For any cleanup, use isopropyl alcohol before the
material is allowed to dry.
2.
Clean hands with Permatex

Fast Orange
®
hand cleaner
or soap and water.
PROPERTIES OF UNCURED MATERIAL
Typical Value
Chemical Type
Epoxy and Mercaptan or Amine
Resins
Mix ratio (volume) 1 : 1
Appearance
Resin
Hardener
Clear
Clear
Odor Mild
Specific Gravity 1.10 - 1.17
Flash Point, TCC >200ºF
Viscosity Heavy syrup
CURING PROPERTIES
Working Time Fixture Time
84160 50-60 seconds 2 – 4 minutes
82516 50-60 seconds 2 – 4 minutes
84101 4 – 5 minutes 8 – 10 minutes
82517 4 – 5 minutes 8 – 10 minutes
84107 30-35 minutes 45-50 minutes
84201 4 – 5 minutes 8 – 10 minutes
Final color Clear to slightly yellow
Temperature range -60°F to +180°F