Specification Sheet

INSTALLATION INSTRUCTIONS
Issue
®
1
• CARTRIDGE REPLACMENT
The filter cartridge in your instant hot tap system needs to be changed every six months in order to
ensure the system works at its optimum performance.
Changing the filter cartridge is a simple matter:
1. Switch off the heater tank either at the mains or by pressing
the centre button on the heater tank touch screen.
*
*
*
I
m
p
o
r
t
a
n
t
N
o
t
i
c
e
*
*
*
r
u
n
o
f
f
a
l
l
h
o
t
w
a
t
e
r
u
n
t
i
l
j
u
s
t
c
o
l
d
w
a
t
e
r
i
s
c
o
m
i
n
g
o
u
t
o
f
t
h
e
t
a
p
.
2. Place a small bowl under the filter housing sump to catch the
small amount of water that will be released when removing the
filter housing sump.
3. Turn the filter housing sump anti-clockwise a quarter turn, to
allow the filter housing sump to drop down from the filter
housing head.
4. Once the sump is removed, unscrew the filter housing cap
from the sump and tip any water out of the sump into the bowl
or sink.
5. Remove the old filter by pulling the filter from the cap.
6. Dispose of the old filter in the normal household waste bin.
R
e
m
e
b
e
r
i
n
g
t
o
k
e
e
p
t
h
e
f
i
l
t
e
r
i
n
s
e
r
t
a
s
y
o
u
w
i
l
l
n
e
e
d
t
h
i
s
f
o
r
t
h
e
r
e
p
l
a
c
e
m
e
n
t
f
i
l
t
e
r
.
7. Fit the new filter by pushing the filter insert into the top of
the filter then into the cap; you may need to wet the ‘O’ seals in
the top of
the filter as shown in the attached drawing referenced A.
Always inspect the 'O' seals for damage; for replacements use
contact details below.
8. Screw the sump back onto the cap (Ensuring that the ‘O’ seal
is in place), referenced B.
9. Push the filter housing sump back into the filter housing head
and turn clockwise until it stops.
I
m
p
o
r
t
a
n
t
N
o
t
i
c
e
The filter is now ready to use – it is vitally important that you
follow the process below to ensure that all air is bled from the
system.
P
l
a
c
e
a
j
u
g
u
n
d
e
r
t
h
e
s
p
o
u
t
a
s
w
a
t
e
r
w
i
l
l
s
p
l
u
t
t
e
r
f
r
o
m
t
h
e
s
p
o
u
t
u
n
t
i
l
a
l
l
o
f
t
h
e
a
i
r
i
s
e
x
p
e
l
l
e
d
.
Operate the instant hot tap lever to dispense water, run-off at
least 0.35 gallons of water, let the system rest for at least 30
seconds and run another 0.35 gallons of water, repeat this at
least one more time – your instant hot water tap should now be
ready for use.
Y
o
u
m
u
s
t
n
o
w
t
h
o
r
o
u
g
h
l
y
c
h
e
c
k
t
h
e
u
n
i
t
f
o
r
a
n
y
w
a
t
e
r
l
e
a
k
s
a
n
d
t
a
k
e
t
h
i
s
o
p
p
o
r
t
u
n
i
t
y
t
o
c
h
e
c
k
f
o
r
a
n
y
e
x
c
e
s
s
w
e
a
r
o
r
d
a
m
a
g
e
t
o
t
h
e
s
y
s
t
e
m
.
I
f
t
h
e
r
e
a
r
e
n
o
l
e
a
k
s
p
l
e
a
s
e
c
o
n
t
i
n
u
e
:
10. Now switch the heater tank back on at the mains, or by
pressing the button in the centre of the heater tank touch
screen.
11. Set the desired temperature by pressing the right hand
button until the desired temperature is displayed (usually 98
degrees)
12. Press the left hand button to confirm the temperature
setting.
13. The heater tank will now heat up to the desired temperature
and once completed the system is ready for use.
FILTER
HOUSING
SUMP
FILTER
HOUSING
CAP
FILTER
MOUNT
BRACKET
FILTER
HOUSING
HEAD
FILTER
INSERT
FILTER
'O' SEAL
(B)
'O' SEALS
(A)
'O' SEALS
(A)
Should you require any advice, or a quick solution to a problem with this product please
contact in the first instance the supplier/showroom from which it was purchased.
• T: 1-800-777-9762 • E: rohlinfo@rohlhome.com • W: www.rohlhome.com
• Instant Hot Tap
9001914U
ConsultyourlocalHouseofRohlshowroomforadditionalinformationandspecications.Forcompletewarrantydetailsandalistofshowrooms,gotohouseofrohl.com
houseofrohl.com