www.rohlhome.com PERRIN & ROWE® HOLBORN C-SPOUT HOT WATER FAUCET, TANK AND FILTER KIT Perrin & Rowe® Kitchen Filtered Hot Water Dispensers U.KIT1347LS FEATURES COLORS/FINISHES • Complete with the following items: • • • • • • • • • • • — U.1998 Hot water tank — U.1347LS-2 Hot water faucet — U.
www.rohlhome.com INSTALLATION INSTRUCTIONS id damaging the IMPORTANT WARNING!! uct for all warranty PLEASE ENSURE THAT THE RECOMMENDED HEATER TANK UNIT (U.1998) AND FILTER KIT (U.1106)IS USED. TO AVOID PRESSURISED BOILING WATER AND TO COMPLY WITH US REGULATIONS THIS IS AN OPEN VENTED PRODUCT. DO NOT PLUG IN THE UNIT UNTIL ALL WATER CONNECTIONS HAVE BEEN MADE AND THE TANK HAS FILLED COMPLETELY THEN FLUSHED TO REMOVE AIR.
www.rohlhome.com INSTALLATION INSTRUCTIONS The Mini Hot Dispensers Collection • Installation & User Guide • Congratulations on the purchase of your Perrin and Rowe Kitchen Product. Correctly installed and with sensible care, this product will give you many years of trouble free service. IMPORTANT INFORMATION Before you proceed... We recommend you engage the services of a registered plumber to install this product. Perrin & Rowe taps require a maximum inlet pressure supply of 75psi.
www.rohlhome.com INSTALLATION INSTRUCTIONS ct. Correctly installed ree service. lumber to install this llations where the be installed prior to Connections to the filter (U.1106) and heater tank U.1998: (See separate filter guide and heater tank installation for further installation instructions) 2 AVOID TRAPPING SILICONE HOSE BETWEEN STUD & BRAIDED HOSES • Once the mains connections are made fit the G3/8" braided hose to the filter as shown.
www.rohlhome.com INSTALLATION INSTRUCTIONS BEFORE USE • Carefully check the installation for leaks. • If further building work is to be carried out in the vicinity, cover the mixer tap to avoid damaging the finish. • Please ensure that the installation complies with the local plumbing codes. ROHL WARRANTY POLICY All products supplied by ROHL carry warranties against manufacturing defects. IMPORTA For full ROHL WARRANTY please contact ROHL or visit www.rohlhome.
www.rohlhome.com INSTALLATION INSTRUCTIONS Electronic Instant Hot Water Appliance Installation, Operation and Care Instructions Please read these instructions fully before commencing the installation and operation of the Electronic Instant Hot Water Appliance Consult your local ROHL showroom for additional information and specifications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
www.rohlhome.com INSTALLATION INSTRUCTIONS We are delighted that you have chosen the electronic instant hot water appliance to compliment your instant hot water Dispenser. This unique electronic instant hot water appliance will save you time and effort when requiring near boiling water for making tea and coffee and we are sure you will discover many new uses each day.
www.rohlhome.com INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS PLEASE READ BEFORE YOU START The alert symbols displayed on the right point to important safety information to make you aware of potential hazards that can cause serious injury or death. Please pay special attention to the information following these warning alerts. Failure to comply with these instructions could result in property damage, serious injury or death.
www.rohlhome.com INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ALL INSTRUCTIONS CAREFULLY When using all electrical appliances, basic safety precautions should always be followed including the information below: To protect against electrical shock, do not place cord, plugs or unit near or in water or other liquids and do not operate the electronic instant hot water appliance controls or power socket with wet hands.
www.rohlhome.com INSTALLATION INSTRUCTIONS INSTALLATION REQUIREMENTS Electrical Requirements A standard 120v electrical outlet is required under the sink. If possible, use a separate circuit dedicated to your Hot Tank. It is recommended that a separate circuit serving only your electronic instant hot water appliance be provided or use an outlet that can be turned on/off by a switch. This electronic instant hot water appliance is equipped with a power supply cord with a power plug.
www.rohlhome.com INSTALLATION INSTRUCTIONS PREPERATION FOR INSTALLATION Unlike other household hot water appliances, this electronic instant hot water appliance is Non Pressurised for safety reasons. For this electronic instant hot water appliance, the Instant Hot Dispenser is placed before the electronic instant hot water appliance, creating an “open vent” system and consequently no pressure is built up inside the appliance.
www.rohlhome.com INSTALLATION INSTRUCTIONS INSTALLATION CONTINUED Step 2 – Connect Dispenser The electronic instant hot water appliance inlet connection is a 3/8” BSP male threaded connector. The outlet connector is a 3/8” BSP male thread connector. Check the connections type and size on the instant hot water Dispenser for the inlet and outlet connections. Screw on the inlet and outlet pipe the correct connectors and tighten with a wrench.
www.rohlhome.com INSTALLATION INSTRUCTIONS INSTALLATION CONTINUED Step 4 – Electrical Connection Ensure that the installation area is dry and no water has spilled. Connect the plug to the power socket and turn on the power socket at the switch. The electronic instant hot water appliance display panel will now light up with the on / off button illuminated.
www.rohlhome.com INSTALLATION INSTRUCTIONS MAINTENANCE AND CARE INSTRUCTIONS CONTINUED Flushing the Instant Hot Water Tank It is recommended that the user flushes through the system completely by drawing off the instant hot water and allowing to reheat and repeating the process for a further 2 or 3 times to ensure the system is fully operational.
www.rohlhome.com INSTALLATION INSTRUCTIONS TROUBLE SHOOTING PROBLEM Water and Steam is spitting from the instant hot water Dispenser spout POSSIBLE CAUSE Unit is boiling WHAT TO DO Turn instant hot water Dispenser handle on and release at least 1 pint of water. Adjust the water temperature on the display to a lower setting. Check aerator is not blocked Bleed system to remove any air Re-Prime bladder to allow correct operation. Water is not hot.
www.rohlhome.
www.rohlhome.com INSTALLATION INSTRUCTIONS Customer Services : ROHL LLC 3 Parker Irvine, California 92618-1605 Phone 800-777-9762 www.rohlhome.com Guarantee Void Unless The Water Filter Is Replaced Every 6 Months Issue : PRV114112017 Rohl & Perrin & Rowe are Registered trade marks. Consult your local ROHL showroom for additional information and specifications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
www.rohlhome.com INSTALLATION INSTRUCTIONS • Instant Hot Tap • ® • CARTRIDGE REPLACMENT The filter cartridge in your instant hot tap system needs to be changed every six months in order to ensure the system works at its optimum performance. Changing the filter cartridge is a simple matter: 1. Switch off the heater tank either at the mains or by pressing the centre button on the heater tank touch screen. ***Important Notice*** – run off all hot water until just cold water is coming out of the tap. 2.
www.rohlhome.com INSTALLATION INSTRUCTIONS • Instant Hot Tap • ® • Filter Installation 1. Fixing Mounting Bracket IT IS VERY IMPORTANT THAT BEFORE YOU START INSTALLING THIS FILTER SYSTEM YOU ENSURE YOU HAVE READ THE INSTALL GUIDES THAT CAME WITH THE TAP AND THE HEATER TANK. First you will need to remove the filter sump. This can be done by turning the sump a quarter turn anti-clockwise and pulling down.
