Model Number PIF-300 wireless pet containment system operating and training guide Please read this entire guide before beginning ™
Important Safety Information Explanation of Attention Words and Symbols used in this guide This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION, used without the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in harm to your pet.
These steps will help keep your pet safe and comfortable. Millions of pets are comfortable while they wear stainless steel contacts. Some pets are sensitive to contact pressure. You may find after some time that your pet is very tolerant of the collar. If so, you may relax some of these precautions. It is important to continue daily checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed. • You may need to trim the hair in the area of the Contact Points.
Thank you for choosing PetSafe® brand. You and your pet deserve a companionship that includes memorable moments and a shared understanding together. Our products and training tools promote a lifestyle of protection, teaching, and love — essentials that influence memories for a lifetime. If you have any questions about our products or training your pet, please visit our website at www.petsafe.net or contact our Customer Care Center at 1-800-732-2677.
FE PETS H A R S SA Components PP Y OW N E Receiver Collar Transmitter Battery (PetSafe® RFA-67) Power Adapter Mo PIF del Number -30 0 Test Light Tool pet PLEA SE wire con opera READ THIS tain ting EN TIR less me and nt s guideyste tra ining E GU IDE BEFO RE m ™ BEGIN NIN G Operating and Training Guide Boundary Flags - 50 Other Items You May Need • • • • • • Pliers Scissors Lighter Drill & mounting hardware Tape measure Non-metallic collar and leash Set up and tra
How the System Works The PetSafe® Wireless Pet Containment System® has been proven safe, comfortable, and effective for pets over 8 pounds. The system works by transmitting a radio signal up to 90 feet in all directions. You temporarily define the Pet Area with Boundary Flags for a visual aid in training your pet. Your pet wears a Receiver Collar with Contact Points that touch his neck, and, once trained, is allowed to roam freely in the Pet Area.
Operating Guide Step Set Up the Transmitter The Transmitter is located at the exact center of the Pet Area. Place the Transmitter: • At least 2 feet above the floor located on the ground floor of your home. • In a dry, well ventilated, protected area. • In an area where temperatures do not fall below freezing (e.g., garage, shed, closet). • On a non-metal table or mount on a wall (1A). A mounting template is included on the back of this guide.
To Set the Static Correction Level Read all steps before attempting to set the Static Correction Level. 1. Remove the clear plastic cover with the edge of the Test Light Tool to expose the Correction Level Button (2D). 2. With the battery installed, press the Correction Level Button and release when the Receiver LED Indicator Light lights up (2E). 3. The Receiver LED Indicator Light will emit a series of flashes representing the Static Correction Level. 4.
Step Make sure the entire Pet Area lies within your property boundaries (3A). Always start determining the Boundary Zone at the shortest distance from Transmitter. Place the Boundary Switch on “Low” if the Boundary Zone will be less than 45 feet from the Transmitter. Make sure the Receiver Collar battery is properly installed, the Static Correction level is set at 2 or greater, and the Test Light Contacts are touching the Contact Points (3B).
Transmitter Range Chart Boundary Control Dial Position Boundary Switch LOW Boundary Switch HIGH 1 5-10 ft. 5-10 ft. 2 5-10 ft. 5-10 ft. 3 15-20 ft. 25-35 ft. 4 20-25 ft. 42-55 ft. 5 25-30 ft. 55-65 ft. 6 35-40 ft. 75-85 ft. 7 40-45 ft. 85-90 ft. 8 40-45 ft. 85-90 ft. Record Your Settings Final Boundary Switch Setting (HIGH or LOW) Final Boundary Control Dial Position (1-8) Receiver Static Correction Level (1-6) Home Camping Vacation Other Note: These distances are approximate.
Step 5 Fit the Receiver Collar Important: The proper fit and placement of your Receiver Collar is important for effective training. The Contact Points must have direct contact with your pet’s skin on the underside of his neck. Please read and follow the instructions in this manual. Proper fit of the collar is important. A collar worn for too long or made too tight on the pet’s neck may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as bed sores.
To Re-Thread the Collar Slide Buckle Ridges The slide buckle prevents the collar from becoming loose around your pet’s neck. The ridges must be facing up; the collar will slip if it is not properly threaded. Training Guide Be Patient With Your Pet Important: Proper training of your pet is essential to the success of the PetSafe® Wireless Pet Containment System®. Read this section completely before beginning to train your pet.
PhaseDay 1 1 - Boundary Awareness Tone Only Training Mode Perform three sessions on day 1, each training session lasting 10-15 minutes. Goal: To have your pet learn that the Boundary Flags and warning beep from the Receiver Collar define the new Pet Area. Setup: • Program the Static Correction Level on the Receiver Collar to Level 1 Tone Only training mode. • Put a separate non-metallic collar on your pet’s neck ABOVE the Receiver Collar and attach a leash.
PhaseDays 2 2 thru 4 - Continue Boundary Awareness Introduction to Static Correction Perform three sessions per day, each lasting 10-15 minutes. Goal: To train your pet to stay in the Pet Area and respect the boundary. Setup: • Program the Static Correction Level on the Receiver Collar to Level 2. • Put a separate non-metallic collar on your pet’s neck ABOVE the Receiver Collar and attach a leash. Be sure the extra collar does not put pressure on the Contact Points.
PhaseDays 4 Training sessions should start at 10-15 minutes, gradually increasing to over an hour. Your pet is ready for this step only when he clearly avoids the entire Boundary Zone, regardless of any distractions or temptations. During this step, do not leave your pet unattended. Goal: To give your pet free run of the Pet Area off the leash. Setup: Adjust the Receiver Collar to the permanent setting appropriate for your pet. Steps: 1. Enter the Pet Area with your pet wearing the Receiver Collar. 2.
Wireless - To - Go Your PetSafe® Wireless Pet Containment System® is completely portable. Follow the set-up procedures (steps 1 through 4) wherever you wish to have containment of your pet. Reestablish the Pet Area and mark it with Boundary Flags so your pet knows his Boundary Zone. Note: If setting up in a metal building or vehicle, the maximum size of the Pet Area may be reduced. Be sure to remove the Receiver Collar battery before turning off the Transmitter.
If I have a question about my Wireless • Contact the Customer Care Center at 1-800-732-2677 or visit our System or need replacement parts, web site at www.petsafe.net. where can I get answers or service? Can I use the Wireless System on an • We do not recommend using any electronic training devices on aggressive pet? aggressive pets. If you are unsure if your dog is aggressive, please consult your veterinarian or a certified trainer.
Troubleshooting The Receiver Collar is not beeping when setting up the Boundary Zone. • The tone may be difficult to hear in a noisy environment. • Use Test Light as explained in the “Test Light Instructions” section, and use it to determine the location of Boundary Zone. • Check that the Transmitter is set up according to directions and install a new battery while standing within 5-10 feet of the Transmitter. • Re-Synchronize the System.
The Receiver Collar is beeping but my pet is not responding to the Static Correction. • Make sure the Static Correction Level is set at 2 or above. • Test the Receiver Collar with the Test Light. • If the Test Light flashes, check the fit of the Receiver Collar. • Trim your pet’s fur where the Contact Points touch the neck and/ or purchase long Contact Points by contacting the Customer Care Center at 1-800-732-2677. • Increase the Static Correction Level. • Repeat training steps to reinforce training.
Re-synchronize the System 1. Remove the Receiver Collar from your pet. 2. Remove the battery from the Receiver Collar. Discharge all power by holding the correction level button down until the LED is no longer illuminated. 3. At the transmitter, move the Boundary Switch from the low to the high position. 4. Slowly adjust the Boundary Control Dial up to 8, down to 1 and then back to the #4 position. 5. Standing within 5-10 feet of the Transmitter, reinsert the battery into the Receiver Collar. 6.
Compliance USA/Canada This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause harmful interference to radio communications.
1-800-732-2677
www.petsafe.
Mounting Template 171 mm (6.75 Inches) Radio Systems® Corporation 10427 PetSafe Way Knoxville, TN 37932 1-800-732-2677 www.petsafe.net Protected by US Patents 6,879,300; 6,921,089; 7,142,167 and D515,027.
