Installation Guide ZPA00-16201 ZPA00-16202 ZPA00-16203 PPA00-16942 PPA00-16943 PPA00-16944 Wall Entry Pet Door Please read this entire guide before beginning
IMPORTANT SAFETY INFORMATION Explanation of Attention Words and Symbols used in this guide This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Thank you for choosing the PetSafe® brand. You and your pet deserve a companionship that includes memorable moments and a shared understanding together. Our products and training tools enhance the relationship between pets and their owners. If you have any questions about our products or training your pet, please visit our website at www.petsafe.net or contact our Customer Care Center at 1-800-732-2677. To get the most protection out of your warranty, please register your product within 30 days at www.
Components Closing Panel Wall Entry Pet Door with Flaps Toggle Bolt 8 pcs. Template Center Locator Washer 8 pcs. Screw Caps 8 pcs. Drywall Screws 8 pcs. Tools Needed • • • • • • • • • • • Framing Square Jigsaw Drill 5 ⁄16” (8 mm) & ½” (13 mm) Drill Bits Phillips Screwdriver Tape Measure Tape Pencil Level Scissors Stud Finder NOTE: Some applications may require the Wall Entry Extension Tunnel (sold separately). See “Replacement Parts and Accessories” on page 10.
Installing Your Wall Entry Pet Door Step 1 Measure 1A. Locate the site for the Wall Entry Pet Door. Locate the studs in 1A Center Between the proposed area. Locate the center between the two studs. Studs 1B Using a pencil, draw a 5” (12.7 cm) vertical line on center about 10” to 12” (25.4 cm to 30.5 cm) above the floor. 1B. Mark the shoulder height of your pet on the vertical line. Draw a horizontal line through your mark.
Fit 3C. Check Using the A side of the pet door, check the fit. Do not force fit if it is tight. 3D. If the hole is too small, simply remove the pet door and re-cut or file the hole slightly to enlarge. Do not cut more than ¹⁄₈” (3.2 mm) from your previous cut. Once the pet door properly goes into the hole, adjust to ensure the unit is square. 3C 3D Step 4 Cut Exterior 4A. Remove the pet door from the wall. Fold up the Center Locator. 4A 4B 4B. Slide the folded piece into the back of A side as shown.
4F. You are now ready to work from the outside wall. 4F Line up the three holes on the template with the three holes that you just drilled. Check for square and tape in position. 4G 4G. Drill out the four corners of the rectangular hole with a 5⁄16” (8 mm) drill bit. Helpful Tip: Use both hands to hold drill steady and straight at a 90° angle. 4H. Carefully cut the hole out using a jigsaw or other appropriate cutting device. Cut on line.
Step 5 Install and Attach Interior Optional Support Installation: 5A. Optional: Measure from the inside of outer wall to the inside of inner wall as shown. Cut a 2X4 to the measured length, making sure that the cut is square. Remove any debris that may be inside the wall where the support will be located. 5B Optional 5B. Optional: Place support inside wall so that the top of support is flush with the bottom of cut-outs.
Step 6 Install and Attach Exterior 6A. You are now ready to work from the outside wall. With B side in 6A position, mark location of 4 toggle bolt holes. Remove B side of the pet door. 6B 6B. Drill marked locations with ½” (13 mm) drill bit. 6C. Install the toggle bolts and screw caps into the B side. Slide the B side of the Pet Door into the A side that is already installed on the inside. The unit will slide together just like it was in the package.
Replacement Flaps Replace & Adjust During extreme changes in weather, vinyl flaps can shrink during cold months and stretch in warmer months. Easily replace or adjust to ensure a snug fit during seasonal changes. To Replace: Remove screws from the frame of pet door. Remove bar and flap. Replace new vinyl flap and position horizontally and vertically to fit into door frame. Replace existing bar and tighten screws in place. To Adjust: Slightly loosen screws Slightly move bar away from flap.
Terms of Use and Limitation of Liability 1. Terms of Use This Product is offered to you conditioned upon your acceptance without modification of the terms, conditions and notices contained herein. Usage of this Product implies acceptance of all such terms, conditions, and notices. 2. Proper Use This Product is designed for use with pets where training is desired. The specific temperament of your pet may not work with this Product.
Claims Procedure Any claim made under this Warranty should be made directly to Radio Systems Australia Pty Ltd Customer Care Centre at: Radio Systems Australia Pty Ltd PO Box 765, Mudgeeraba QLD 4213 Australia Residents: 1800 786 608 New Zealand Residents: 0800 543 054 Email: info@petsafeaustralia.com.au To file a claim, a proof of purchase must be provided. Without a proof of purchase, Radio Systems will not repair or replace faulty components.