295 1296 Instruction manual 296-12-18 135 Betriebsanleitung engl. 08.
This Instruction manual is valid for all models and subclasses listed in the chapter „Specifications“. The reprinting, copying or translation of PFAFF Instruction Manuals, whether in whole or in part, is only permitted with our previous permission and with written reference to the source. G.M. PFAFF Aktiengesellschaft Postfach 3020 D - 67653 Kaiserslautern Königstr.
Index Contents ................................................................................. Chapter-Page 1 1.01 1.02 1.03 1.04 1.05 1.05.01 1.05.02 1.06 Safety ........................................................................................................................ 1 Regulations ................................................................................................................ 1 General notes on safety ........................................................................
Index Contents ................................................................................. Chapter-Page 8.01.06 8.02 8.03 Assembling the reel stand ......................................................................................... 8 - 4 Commissioning .......................................................................................................... 8 - 4 Switching the machine on/off .................................................................................... 8 - 4 9 9.01 9.
Index Contents ................................................................................. Chapter-Page 11.05 11.05.01 11.05.02 11.05.03 11.05.04 11.05.05 11.05.06 11.05.07 11.05.08 11.05.09 11.05.10 11.05.11 11.05.12 11.05.13 11.05.14 Adjusting the thread trimmer -900/56 ...................................................................... 11 - 20 Engaging solenoid ....................................................................................................
Safety 1 Safety 1.01 Regulations This machine has been made according to the European regulations indicated in the conformity and manufacturer’s declarations.
Safety ● Only spare parts which have been approved by us are to be used for repairs! We draw special attention to the fact that spare parts and accessories not supplied by us have not been subjected to testing nor approval by us. Fitting and/or use of any such parts may cause negative changes to the design properties of the machine. We shall not accept any liability for damage caused by the use of non-original parts. 1.03 Safety symbols ! Danger! Special points to observe.
Safety 1.05 Notes for operating and technical staff 1.05.01 Operating staff Operating staff are the persons responsible for setting up, operating and cleaning the machine and for removing any disturbances in the sewing area.
Safety 1.06 Danger warnings A working area of 1 m must be kept free both in front of and behind the machine, so that easy access is possible at all times.
Proper use 2 Proper use The PFAFF 1295 is a single-needle lockstitch postbed sewing machine with unison feed and large vertical sewing hook. The PFAFF 1296 is a two-needle lockstitch postbed sewing machine with unison feed and large vertical sewing hooks. These machines are for sewing lockstitch seams in the textile industry.
Specifications 3 Specifications 3.01 PFAFF 1295, PFAFF 1296 ◆ Stitch type: .................................................................................................. 301 (lockstitch) Needle system ....................................................................................................... 134 - 35 Needle size in 1/100 mm: Version B : ............................................................................................................. 80 - 100 Versiong CN : .....................
Specifications 3.02 Possible versions and subclasses Version B (only on 1296): ..................................................... For sewing medium materials Version CN: ................................................................ For sewing medium-heavy materials Work aids: Subclass -900/56 ......................................................................................... Thread trimmer Subclass -911/97 ................................ Automatic presser foot lift with backtacking system 3.
Disposal of machine waste 4 Disposal of the machine ● Proper disposal of the machine is the responsibility of the user. ● The materials used for the machine are steel, aluminium, brass and various plastics. The electrical equipment comprises plastic materials and copper. ● The machine must be disposed of according to the locally valid pollution control regulations; if necessary, a specialist will have to be contracted.
Transportation, packing and storage 5 Transportation, packing and storage 5.01 Transportation to the customer’s premises Within the Federal Republic of Germany, complete machines (with table and motor) are delivered without packing. Machines without table (sewing heads only) and machines intended for exports are packed. 5.02 Tansportation inside the customer’s premises The manufacturer cannot be made liable for transportation inside the customer’s premises nor to other operating locations.
Explanation of symbols 6 Explanation of symbols In this instruction manual, work to be carried out, or important information, is accentuated by symbols.
Controls 7 Controls 7.01 On/off switch ● The power supply to the machine is switched on or off by turning switch 1. The illustrated on/off switch is fitted to machines with Quick motors. If other motors are used, a different switch may be fitted. O 1 Fig. 7 - 01 7.02 Pedal (on machines without subclass -911/97) 0 = Neutral position +1 = Sewing -1 = Thread trimming (on machines with thread trimmer) 0 +1 -1 Fig.
Controls 7.03 Pedal (on machines with subclass -911/97) 0 = Neutral position +1 = Sewing -1 = Raise presser foot -2 = Thread trimming (on machines with thread trimmer) 0 +1 For further pedal functions please refer to the instruction manual of the motor manufacturer. -1 -2 Fig. 7 - 03 7.04 Knee lever (on machines without subclass -911/97) ● The presesr foot is raised by pressing knee lever 1. 1 Fig.
Controls 7.05 Key on machine head (on machines with subclass -911/97) ● If key 1 is pressed during sewing, the machine will switch to reverse sewing. 1 Fig. 7 - 05 7.06 Presser bar lifter ● The presser foot is lifted by raising presser bar lifter 1. 1 Fig.
Controls 7.07 Feed regulator/reverse sewing ● The stitch length is adjusted by turning the knurled nut on lever 1. ● To reverse the sewing direction press lever 1 fully upwards. 0 1 2 3 1 Fig. 7 - 07 7.08 Feed regulator (on machines with subclass -911/97) ● Turn knurled screw 1 to adjust the stitch length for sewing forwards. ● Turn knurled screw 2 to adjust the stitch length for sewing backwards. 2 Reverse stitches can be set as long as required, independently of forward stitches.
Controls 7.09 Adjusting nut for the top feed stroke Switch off the machine! 2 + Fig. 7 - 09 7-5 3 1 ● Loosen screw 1 at the back of the machine. ● Open cover 2. ● Loosen screw 3 and adjust lever accordingly. ● Close cover 2 and tighten screw 1.
Installation and commissioning 8 Installation and commissioning The machine must only be installed and commissioned by qualified personnel! All relevant safety regulations must be strictly adhered to! If the machine is delivered without a table, be sure to use a stand and table that will reliably support the weight of the machine with its motor. It is very important to ensure that the stand of the machine is firm and steady, also during sewing. 8.
Installation and commissioning 8.01.02 Tensioning the v-belt ● Loosen nuts 1. ● Tension v-belt by adjusting bracket 2. ● Tighten nuts 1. Fig. 8-02 shows a Quick motor. If a different motor is used, please refer to the instruction manual of the motor manufacturer. 2 cm 1 2 Fig. 8 - 02 8.01.03 Fitting the upper belt guard 6 If a large balance wheel is in use, break off corner 1 of belt guard part 3. 4 2 5 3 8 7 6 8 Fig. 8 - 03 8-2 8 4 ● ● ● ● Screw stop piece 2 onto belt guard part 3.
Installation and commissioning 8.01.04 Fitting the lower belt guard ● Position belt guard 1 so that motor pulley and v-belt can run freely. Fig. 8-04 shows a Quick motor. If a different motor is used, please refer to the instruction manual of the motor manufacturer. 1 Fig. 8 - 04 8.01.05 Fitting the synchroniser ● Push synchroniser 1 onto the shaft. ● Tighten screws 2 a little. ● Connect the synchroniser plug at the control box. ● Adjust the synchroniser (see Chapter 11.05.
Installation and commissioning 8.01.06 Assembling the reel stand ● Assemble the reel stand as shown in Fig. 8-06. ● Afterwards insert the stand in the hole in the table top and secure it with the nuts provided. Fig. 8 - 06 8.02 Commissioning ● Check the machine, particularly its electrical wiring and pneumatic tube connections, for any damage. ● Clean the machine thoroughly and afterwards fill it with oil and oil the machine (see Chapter 10, Care and maintenance).
Setting up 9 Setting up All instructions and regulations in this manual must be observed. Special attention must be given to all safety regulations! All setting-up work must only be done by personnel with the necessary training. For all setting-up work the machine must be isolated from the power supply by turning off the on/off switch or removing the machine plug from the electric power socket! 9.
Setting up 9.02 Inserting the needles on the PFAFF 1296 Switch off the machine! Danger of injury due to unintentional starting of the machine! Only use needles of system 134-35. ● Set needle bar at top position and loosen screws 1. ● Push needles 2 fully in (the long groove of the left needle must face to the right and that of the right needle to the left). ● Tighten screws 1 again. 1 2 Fig.
Setting up 9.03 Winding the bobbin thread, regulating the winder tension 4 + - 6 3 1 2 5 Fig. 9 - 03 ● Place an empty bobbin 1 on winder spindle 1. ● Thread up as shown in Fig. 9-03 and wind the thread a few ttimes clockwise around bobbin 1. ● Engage the bobbin winder by pressing spindle 2 and lever 3 simultaneously The bobbin is wound during sewing. ● The tension of the thread wound onto bobbin 1 is set on knurled screw 4.
Setting up 9.04 Changing the bobbin Switch off the machine! Danger of injury due to unintentional starting of the machine! 2 Removing the bobbin case: ● Set the take-up lever at its highest point. ● Remove the post cover, lift latch 1 and take out bobbin case 2. 1 Inserting the bobbin case: ● Insert bobbin case 2 so that you feel it snap in place. ● Push latch 1 down and close the post cover. Fig. 9 - 04 Do not run the machine with the post cover open! Danger of injury by moving parts! 9.
Setting up 9.06 Threading needle thread/adjusting needle thread tension on the PFAFF 1295 1 Fig. 9 - 06 Switch off the machine! Danger of injury due to unintentional starting of the machine! ● Thread needle thread as shown in Fig. 9-06. Be sure to thread the needle from the left. ● Regulate the needle thread tension by turning knurled screw 1.
Setting up 9.07 Threading needle thread/adjusting needle thread tension on the PFAFF 1296 2 1 Fig. 9 - 07 Switch off the machine! Danger of injury due to unintentional starting of the machine! ● Thread needle threads as shown in Fig. 9-07. Be sure to thread the right needle from the left and the left needle from the right. ● Regulate the needle thread tensions by turning knurled screw 1 (right needle) or 2 (left needle).
Care and maintenance 10 Care and maintenance Check air pressure ........................................................ daily, each time before operation Clean hook area ............................................ daily, in continuous operation several times Check water bowl of air filter/regulator .......................................... daily, before operation Oil hook ......................................................................................................................
Care and maintenance 10.02 General oiling 0 1 2 3 Fig. 10 - 02 ● Apply oil at all bearing points above the table (see arrows) twice a week. Switch off machine! Danger of injury! ● Pull knee lever out to the front and tilt machine backwards. ● Apply oil at all bearing points beneath the table (see arrows) twice a week.
Care and maintenance Only use oil with a medium viscosity of 22.0 mm²/s at 40° C and a density of 0.865 g/cm³ at 15°C! We recommend PFAFF sewing-machine oil, part No. 280-1-120 144. 10.03 Oiling the sewing hook Switch off the machine! Danger of injury due to unintentional starting of the machine! ● Open the post cover. ● Set the needle bar at its highest position. ● Apply 1 or 2 drops of oil in hole 1 of the hook gib.
Care and maintenance 10.04 Oiling the needle-head parts Switch off the machine! Danger of injury due to unintentional starting of the machine! ● Remove the faceplate. ● Oil all moving parts and bearing points (see arrows) twice a week. ● Refit the faceplate. Only use oil with a medium viscosity of 22.0 mm²/s at 40° C and a density of 0.865 g/cm³ at 15°C! We recommend PFAFF sewing-machine oil, part No. 280-1-120144. Fig. 10 - 04 10.
Care and maintenance 10.06 Checking/regulating the air pressure ● Check the air pressure on gauge 1 every time before operation. ● Gauge 1 must show a pressure of 6 bar. ● Regulate this pressure if required. To do so, pull knob 2 up and turn it accordingly. 2 8 10 6 100 150 4 12 50 200 2 14 230 0 16 0 1 Fig. 10 - 06 10.07 Emptying/cleaning the water bowl of the air filter/regulator Switch off the machine. Disconnect the air hose at the air filter/regulating unit.
Adjustment 11 Adjustment For the adjustments in this chapter the PFAFF 1296 two-needle machine is illustrated. On the PFAFF 1295 single-needle machines various adjustments only have to be carried out on one side, i.e. in the right-hand hook area. This is referred to in the different chapters. 11.01 Tools, gauges and other equipment for adjusting ● ● ● ● ● ● ● ● 11.
Adjustment 11.04 Adjusting the basic machine 11.04.01 Position of the bottom feed dog crosswise to sewing direction Requirement The bottom feed dog must be the same distance from the left and right side of the feed slots. 4 1 X 3 2 X 1 4 Fig. 11 - 01 ● Loosen screws 1 and 2. ● Position rock shaft 3 according to Requirement.. ● Tighten screw 1. The flats of pins 4 must face screws 1 and rock shaft 3 must neither have any play nor bind. Leave screws 2 loose for the following adjustments.
Adjustment 11.04.02 Adjusting the bottom feed dog in sewing direction Requirement With the longest stitch length set, the bottom feed dog must not strike the feed slot at the front or rear end of its stroke. 1 2 Fig. 11 - 02 ● Set the longest stitch length. ● Turn rock shaft 1 according to Requirement. and tighten screws 2.
Adjustment Bottom feed dog height Requirement With the stitch length set at "0" the feed dog must protrude from the needle plate by the height of its teeth when at its highest position. 2 tooth height 11.04.03 1 Fig. 11 - 03 ● Set stitch length „0“. ● Turn the balance wheel to set the bottom feed dog at its highest position. ● Adjust bracket 1 (screws 2) according to Requirement. On machines without bottom-feed lifting phase (without "P") the feed dog height may be reduced somewhat if necessary.
Adjustment 11.04.04 Needle height (preliminary adjustment) Requirement With the needle bar at b.d.c. the clearance between needle bar and needle plate must be 15 mm. 2 1 15 mm 1 Fig. 11 - 04 ● Re-position the height of needle bar 1 (screws 2) according to Requirement, but do not turn it.
Adjustment 11.04.05 Needle in needle-hole centre Requirement With the stitch length set at "0" the needle must enter exactly in the centre of the needle hole. 4 3 0 1 2 3 7 6 5 8 9 1 2 Fig. 11 - 05 ● ● ● ● ● ● ● Remove vibrating presser 1 and lifting presser 2. Set the stitch length at "0" and set the needle bar at t.d.c. Insert a new needle, loosen screws 3, 4, 5 and 6. Turn the balance wheel to set the needle immediately above the bottom feed dog.
Adjustment 11.04.06 Bottom feed dog lifting motion Requirement 1. With the needle bar at b.d.c. the feed dog must be at its highest position. 2. When the longest stitch length is set and the balance wheel is turned, the bottom feed dog must reach the top side of the needle plate at the same time as the needle. 1 2 Fig. 11 - 06 This adjustment does not apply to machines without bottom-feed dog lifting phase (without "P") ● Set needle bar at b.d.c.
Adjustment 11.04.07 Feeding stroke of bottom and top feeds Requirement With the longest stitch length set and the needle bar at b.d.c. neither the top- nor bottom feed must make any movement when the reverse-feed lever is operated. 2 1 Fig. 11 - 07 ● ● ● ● ● ● Set the longest stitch length. Undo screw 1 enough to allow eccentric 2 to be turned on the shaft against a resistance. Set needle bar at b.d.c. First turn eccentric 2 so that its highest eccentric point is facing "downwards.
Adjustment 11.04.08 Hook clearance, needle rise, needle height and needle guard Requirement With the stitch length set at "3" and in needle-rise position (= 1.8 mm past b.d.c. on version "B" or 2.0 mm past b.d.c. on version "C") 1. The hook point must be at the "needle centre" and the clearance between hook and needle 0.05 to 0.1 mm, 2. the top end of the needle eye must be 0.8 to 0.1 mm below the hook point, and 3. needle guard 8 must touch the needle just lightly. 0.05 - 0.
Adjustment ● Set the hook point at the needle centre, making sure that the needle is not deflected by needle guard 8. ● Making sure that bevel gear 6 is not too close, but the hook has not too much play, tighten screws 2. ● Move fixing collar 7 up against bevel gear 6 and tighten screws 3. ● Adjust the needle height according to Requirement 2 (see also Chapter 11.04.04, Needle height preliminary adjustment). ● position needle guard 8 according to Requirement 3.
Adjustment 11.04.09 Top feed stroke Requirement With the longest top feed stroke set and the stitch length at "0", lifting presser 1 and vibrating presser 2 must each rise from the needle plate by 7.0 mm when the balance wheel is turned. 4 7 mm 3 1 7 mm 2 Fig. 11 - 09 ● Set the longest top feed stroke and stitch length "0". ● Lower lifting presser 1. ● Turn the balance wheel in sewing direction until vibrating presser 2 has reached its highest point.
Adjustment 11.04.10 Top feed lifting motion Requirement When lifting presser 1 is resting on the needle plate, vibrating presser 4 and needle point 5 must reach the needle plate at the same time at the highest top feed stroke. 3 2 5 1 4 Fig. 11 - 10 ● Lower lifting presser 1 onto the needle plate. ● Loosen screws 2 just enough to allow eccentric 3 to be turned against a resistance on it shaft. ● Turn eccentric 3 according to Requirement. ● Tighten screws 2.
Adjustment 11.04.11 Bobbin case opener Requirement The needle thread must neither be trapped between bobbin case opener 3 and hook base 4 nor between position finger 5 and the retainer on the needle plate (see arrows). 2 6 5 1 3 4 Fig. 11 - 11 ● Undscrew and remove post covers 1 (on left post from the rear). ● Undo screws 2 enough to allow bobbin case opener 3 to be turned on its shaft against a resistance. ● Thread up the machine, place sewing material in and lower the lifting presser.
Adjustment 11.04.12 Slip coupling Slip coupling 4 is adjusted at the works. When a thread jams, slip coupling 4 disengages, in order to avoid damage to the hooks. To engage the coupling again, proceed as follows. 1 2 4 3 4 Fig. 11 - 12 ● Remove jammed thread. ● Press plunger 1 and turn the balance wheel until pawl 2 engages groove 3.
Adjustment 11.04.13 Needle-thread tension release Requirement With the lifting presser raised, there must be a clearance of at least 0.5 mm between tension discs 4. 2 0.5 mm 1 3 4 Fig. 11 - 13 ● Position pressure plate 1 behind mounting bracket 2 according to Requirement. The clearance of 0.5 mm is a miminum setting and may be as much as 1 mm for heavy threads. When the tension is engaged, release pin 3 must not be under load.
Adjustment Thread check spring, without subclass -900/56 Requirement The movement of thread check spring 5 must be finished when the needle pointe enters the material (=spring stroke of about 7 mm). 7 mm 11.04.14 5 1 3 2 4 Fig. 11 - 14 ● Adjust stop 1 (screw 2) according to Requirement. ● To adjust the pressure of the spring, turn screw 3 (screw 4). For technical reasons the length of the thread check spring stroke may vary upwards or downwards a little.
Adjustment 11.04.15 Thread check spring on the PFAFF 1296 with subclass -900/56 Requirement The movements of thread check springs 1 and 6 must be finished when the needle points enter the material (=spring stroke of about 7 mm). 8 10 5 6 7 mm 1 4 2 9 7 3 Fig. 11 - 15 ● ● ● ● To adjust the pressure of spring 1, turn screw 2 (screw 3). Adjust stop 4 (screw 5) according to Requirement. To adjust the pressure of spring 6, turn screw 7 (screw 8). Adjust stop 9 (screw 10) according to Requirement.
Adjustment Bobbin winder Requirement 1. With the bobbin winder engaged, drive wheel 1 must be driven reliably. 2. With the bobbin winder disengaged, friction wheel 5 must not run against drive wheel 1. 3. The bobbind winder must switch itself off when the filled thread is about 1 mm from the rim of the bobbin. 1 5 2 4 1 mm 11.04.16 3 Fig. 11 - 16 ● Re-position drive wheel 1 (screws 2) according to Requirements 1 and 2. ● Re-position pin 3 (screw 4) according to Requirement 3.
Adjustment 11.04.17 Pressure of the lifting presser Requirement 1. The material must be properly fed, even at the highest sewing speed. 2. There must be no pressure marks on the material. 1 Fig. 11 - 17 ● Turn screw 1 according to the Requirement.
Adjustment 11.05 Adjusting the thread trimmer -900/56 11.05.01 Engaging solenoid Requirement 1. Mounting bracket 1 must be in the middle of its adjusting range and parallel with the right-hand edge of the mounting bracket. 2. When the thread trimmer is in its resting position the core of solenoid 3 must protrude from the solenoid housing by about 4 mm. 4 mm 4 3 1 2 Fig. 11 - 18 ● Re-position bracket 1 (screw 2) according to Requirement 1.
Adjustment 11.05.02 Control cam (preliminary adjustment) Requirement 1. Control cam 1, must be centred with the cutout of bearing mounting 5. 2. With the needle bar at t.d.c., screws 2 must be visible from the front and aligined parallel with the bedplate. 2 4 4 3 3 1 5 Fig. 11 - 19 ● Re-position control cam 1 (screws 2) and fixing collars 3 (screws 4) according to Requirement.
Adjustment 11.05.03 Control lever spring action Requirement When the thread trimmer is in its resting position, it must be possible to press control lever 3 about 1 mm towards the bedplate (spring action). 2 3 1 Fig. 11 - 20 ● Turn screw 1 (nut 2) according to Requirement.
Adjustment 11.05.04 Control lever stroke Requirement 1. When engaging lever 5 is operated the pin of control lever 6 must drop freely into the track of control cam 7. 2. After thread trimming, control lever 6 must pass freely on the right side of stop plate 3 and engage control lever 5 behind stop plate 3. 3. There must be a clearance of 0.2 mm between the pin of control cam 6 and the righthand inside of the control cam track. 0.2 mm 4 5 2 3 6 1 7 Fig.
Adjustment 11.05.05 Thread-trimmer drive linkage Requirement 1. On the PFAFF 1296 thread-catcher drive linkage 1 must have a length of 128 mm, less half of the needle gauge. On the PFAFF 1295, thread catcher drive linkage 1 must have a length of 128 mm 2. When the threa trimmer is in its resting position there must be a clearance of about 1 mm between plunger 5 and lever 6. 128 mm 2 1 2 6 1 mm 5 3 4 Fig.
Adjustment 11.05.06 Linkage bar (only on the PFAFF 1296) Requirement The length of linkage bar 1 must be the same as the distance between the two threadcatcher drive shafts 3. = 3 3 1 2 = 2 Fig. 11 - 23 ● Adjust middle section 1 (nuts 2) of the linkage bar according to Requirement.
Adjustment Thread catcher height Requirement There must be a clearance of 0.7 mm between the underside of thread catcher 4 and bobbin case cap 5. 0.7 mm 11.05.07 4 4 5 2 3 1 Fig. 11 - 24 ● Loosen screws 1 and 2. ● Adjust the height of shaft 3 according to Requirement. ● Tighten screws 1. Leave screws 2 loose for the following adjustment.
Adjustment 11.05.08 Thread catcher resting position Requirement When the thread trimmer is in its resting poistion there must be a clearance of about 4 mm between the point of catcher 3 and the cutting edge of knife 4. 4 mm 3 3 4 1 2 Fig. 11 - 25 ● Turn shaft 2 according to Requirement. ● Tighten screws 1. When tightening screws 1 make sure that all transmission parts of the thread catcher drive can move freely.
Adjustment 11.05.09 Knife pressure Requirement When the front edge of thread catcher 3 has passed the knife cutting edge by half, knife 1 must rest with light pressure on the edge of the catcher. 3 2 3 1 Fig.
Adjustment 11.05.10 Bobbin thread trapping spring Requirement 1. Bobbin thread trapping spring 3 must not be deflected by thread catcher 4 in any phase. 2. After the trimming action the bobbin thread must be securely trapped. 3. It must be possible to insert and remove the bobbin from the hook without any hindrance. 3 1 4 4 3 2 Fig. 11 - 27 ● Re-position bracket 1 (screws 2) according to Requirements 1 and 3. ● Bend trapping spring 3 according to Requirement 2.
Adjustment 11.05.11 Control cam (final adjustment) Requirement The trimming action must be just completed when the take-up lever is at t.d.c. 2 1 Fig. 11 - 28 ● Turn control cam 1 (screws 2) according to Requirement.
Adjustment 11.05.12 Release lever Requirement When the pin of control lever 3 has dropped into the track of control cam 4 and the needle bar is at b.d.c. there must be a clearance of about 1 mm between control lever 3 and release lever 5. In this position the needle thread tension must still be engaged. 4 2 5 3 1m m 1 Fig.
Adjustment 11.05.13 Release rod Requirement 1. When the lifting presser is resting on the needle plate, pin 3 must rest at the lower end of the elongated hole in pull-rod 1. 2. The tension discs must not be moved apart in this position. 2 1 3 1 Fig. 11 - 30 ● Re-position pull-rod 1 (screws 2) according to Requirement.
Adjustment 11.05.14 Adjusting the synchroniser Requirement 1. When sewing is interrupted, the machine must position at about 4 mm past b.d.c. of the needle bar. 2. After thread trimming the machine must position with the take-up lever at t.d.c. ● Carry out adjustment according to instruction manual of motor.
Notes
G.M. PFAFF Aktiengesellschaft Postfach 3020 D-67653 Kaiserslautern Königstr. 154 D-67655Kaiserslautern Telefon: (0631) 200-0 Telefax: (0631) 17202 Telex: 45753 PFAFF D Gedruckt in der BRD Printed in Germany Imprimé en R.F.A. Impreso en la R.F.A.
