Instructions

INSTALL:
4x
INSTALL:
2x
INSTALL:
4x
CLEARANCE REAR
TOPFRONT
Thank you for choosing Phanteks. Please take a
moment to carefully go through the manual.
Phanteks will not take responsibility for any
damages incurred due to incorrect installation or
usage of this product.
This manual supports the following models:
PH-EC500ATG_BK (2x 140 mm Black Fans)
PH-EC500ATG_DBK (3x 140 mm D-RGB Fans)
PH-EC500ATG_DWT (3x 140 mm D-RGB Fans)
COLO RS
2 SEC
MODE S
SOLID
BREATHING
RADA R
SPARKL E
RAINBOW
PRESS AND HOLD THE MODE BUT TO N TO TURN OFF LED S
PRESS AGAIN TO TURN ON
Digital-RGB CONTROLS (P500A_D MODEL)
INTRODUCTION INCLUDED ACCESSORIES
P500A INCLUDED ACCESSORIES:
PRODUCT OVERVIEW
ECLIPSE P500A
INSTALLATION GUIDE V1.0
OPTIONAL UPGRADES
ECLIPSE P500A
a. INSTALL 4X DUAL SYSTEM STAND-OFFS ON
THE BOTTOM SIDE OF THE ITX BRACKET
c. CONNECT THE POWER SWITCH & POWER LED
CONNECTOR TO THE MOTHERBOARD
e. INSTALL THE ITX BRACKET
WITH 4x ITX BRACKET SCREWS
d. REMOVE THE DUAL SYSTEM
COVER FROM THE CHASSIS
English
1. Headphone / Microphone
2. USB 3.0
3. USB-C Gen 2
4. D-RGB Color
(P500A-D only)
5. D-RGB Mode
(P500A-D Only)
6. Reset Button
(P500A Only)
7. Power Button
Francais
1. Casque / Microphone
2. USB 3.0
3. USB-C Gen 2
4. D-RGB Color
(P500A-D Only)
5. D-RGB Mode
(P500A-D Only)
6. Bouton de réinitialisation
(P500A Only)
7. Bouton d’alimentation
Deutch
1. Kopfhörer / Mikrofon
2. USB 3.0
3. USB-C Gen 2
4. D-RGB Color
(P500A-D Only)
5. D-RGB Mode
(P500A-D Only)
6. Reset-Knopf
(P500A Only)
7. Ein-/Aus Schalter
Espanol
1. Auricular / Micrófono
2. USB 3.0
3. USB-C Gen 2
4. D-RGB Color
(P500A-D Only)
5. D-RGB Mode
(P500A-D Only)
6. Botón de reinicio
(P500A Only)
7. Botón de encendido
ECLIPSE P500A BLACK ECLIPSE P500A DIGITAL-RGB
FRONT I/O FEATURES
a. INSTALL RISER CABLE WITH 2x
RISER CABLE SCREWS.
b. INSTALL VERTICAL GPU MOUNT
WITH 2x HEX SCREWS
B
A
B
A
f. (OPTIONAL) IF USING THE X16 RISER CABLE TO INSTALL A VERTICAL
GPU TO SECOND SYSTEM, MOVE THE VELCRO TIE FOR EASY
RISER CABLE ROUTING
STEP 9.
VERTICAL GPU MOUNT - OPTIONAL
STEP 10.
INSTALLING A DUAL SYSTEM - OPTIONAL
2x 140 mm Black or
3x 140 mm D-RGB
3x 2.5” SSD Brackets
(Pre-Installed)
2x 3.5” HDD Brackets
LOOSEN:
2x
2
STEP 1.
REMOVING CHASSIS PANELS
a. OPEN THE LEFT SIDE PANEL,
THEN LIFT UP THE PANEL
TO REMOVE IT.
b. LOOSEN THE THUMB SCREWS ON
THE RIGHT SIDE PANEL THEN
SLIDE THE PANEL OFF.
c. REMOVE FRONT PANEL BY
PULLING ON THE PANEL
FROM BELOW
(RISER CABLE SOLD SEPERATELY PH-CBRS_FL22)
(REQUIRES ITX UPGRADE KIT PH-ITXKT_R01 AND THE REVOLT X POWER SUPPLY PH-P1#00PS)
b. INSTALL ITX MOTHERBOARD
ON BRACKET USING INCLUDED
MOTHERBOARD SCREWS
INSTALL:
4x
120
FAN
140
FAN
120
RAD
140
RAD
1
2
3
4
1
2
3
6
5
77
120
FAN
140
FAN
120
RAD
140
RAD
120
FAN
140
FAN
120
RAD
140
RAD
CPU Cooler Height 190 mm
GPU Clearance 435 mm
Front Radiator Clearance 95 mm
Top Radiator Clearance 65 mm
INSTALL:
2x
1
MOVE:
1x
1x
The GPU Mount has two
mounting positions. Position A
allows for better air cooling and
3-slot GPU cards.
(RISER CABLE SOLD SEPERATELY PH-CBRS_PR60)
REMOVE:
2x
12x Thumb Screw
7x PSU Screw
8x Fan Screw
6x Case Screw 3x Riser Cable
Screw
4x Dual-
System Stando
8x HDD Screw Stando
Removal Tool
6x Zip Ties1x Vertical GPU Mount1x Anti-Sag Bracket
22x Motherboard
+ SSD Screw
1x Motherboard
Stando