ASSEMBLY INSTRUCTIONS USER’S MANUAL Before starting assembly: Read all instructions throughly. Open and check boxes for parts list. If any parts are broken or missing call or email customer service. Keep all packaging until you are satisfied with your product. Returns are not accepted without original packaging. Make sure you have ample space for assembly. WARNING: DO NOT FULLY TIGHTEN ALL SCREWS UNTIL ASSEMBLY IS COMPLETE. DO NOT strain yourself.
Assembly Instructions 28 Inch Gas Fire Pit Table DANGER · FLAMMABLE GAS UNDER PRESSURE. LEAKING LP-GAS MAY CAUSE A FIRE OR EXPLOSION IF IGNITED CAUSING SERIOUS BODILY INJURY OR DEATH. CONTACT LP GAS SUPPLIER FOR REPAIRS, OR DISPOSAL OF THIS CYLINDER OR UNUSED LP-GAS. WARNING · FOR OUTDOOR USE ONLY.* DO NOT USE OR STORE CYLINDER IN A BUILDING, GARAGE OR ENCLOSED AREA. WARNING: WHEN CONNECTING FOR USE: · · · Use only in compliance with appliable codes. Know the odor of LP-gas.
Table of Contents Table of Contents ..........................................................2 Safety Information...........................................................2-4 Pre-Assembly...……………………...…………………….5 Package Contents ..………………...……………………. 6 Assembly..……………………………… ………....…8-10 Operating Instructions .........................................1 3 Maintenance...........................................................14 Care and Cleaning ................................................
Safety Information (continued) WARNING: You must provide propane gas and propane cylinder. Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system. See Chapter 5 of the Standard for Storage and Handling of Liquefied Petroleum Gas, ANS/NFPA 58. Your local library or fire department should have this book. The pressure regulator and hose assembly supplied with the appliance must be used.
Safety Information (continued) WARNING: Solid fuels shall not be burned in this appliance. The installation must conform with local codes or, in the absence of local codes, ANSIZ223. 1/NFPA54, NFPA58 Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2.
Pre-Assembly PLANNING ASSEMBLY Carefully remove all pieces from the carton and make sure that you have all parts (refer to the hardware and package contents list). If you are missing parts, please contact 855-600-9294 for further assistance. YOUR OWNER’S MANUAL Keep and store this Owner’s Manual for future reference. It contains important instructions and procedures for safety and maintenance. NOTE: Please read and understand the entire manual before you assemble, operate, or install the fire pit.
Package Contents E F G I B I B C A H K 6 J
Package Contents A Front Leg 1 B Back Leg 2 C Front Leg 1 E F G H 1 Lid 1 Fire Glass 1 Table Top With Burner Door 1 I Side Panel 2 J Side Panel With Window 1 K 1 Gas Tank Support L Handle 1 EE AAA Battery 1 7
Assembly Step 1: B B Connect all four Legs (A,B,C,) to the Table Top with Burner (G) by using four M6 x10 Bolts (AA). A C AA NOTE: PLACE TABLE TOP TO NON-ABRASIVE SURFACE. PLEASE DON’T TIGHTEN THE HARDWARE AT THIS TIME. Don’t tighten the hardware. B Step 2: I B C Connect Side Panel (I) to Back Leg (B) by using four M6 x 10 Bolts (AA). A Connect Side Panel (I) to Front Leg (C) and the other Back Leg (B) by using four M6 x10 Bolts (AA).
Assembly (continued) Step 4: Connect Gas Tank Support (K) to the semi-assembled body by using four M6x10 bolts(AA) . Please tighten all the screws for step 1-4. AA Step 5: Slide the hinge of Door (H) to Front Leg (C). H E Step 6: Place the fire glass into fire bowl. Note: Ensure no fire glass is placed on the ignition portion of the burner. Then place the Lid (E) on. Note: The cover must be removed when the burner is in operation. Wait until the unit cools before installing the cover.
Assembly (continued) Step 7: Put the cylinder into the Gas Tank Support (K), and secure the cylinder by tightening the screw in the gas tank support. Connect the hose and regulator to cylinder The propane cylinder is sold separately. Use a standard 20 lbs propane cylinder only. Step 8: Open the ingniter cover and place the AAA battery into it. Then tighten the ingniter cover completely.
Operating WARNING: Never use this appliance for other than the intended use. DO NOT use this appliance to prepare food. Initial Lighting: When lit for the first time, the appliance emits a slight odor. This is a normal temporary condition caused by the “burn-in ” of internal paints and lubricants used i n the manufacturing process and does not occur again. Simply run the main burner on high for approximately one-half hour.
Operating (continued) LEAK TESTING OPERATION WARNING: A leak test must be performed annually or if a part of the gas system is replaced. WARNING: Never use an open flame to check for gas leaks. Be certain no sparks or open flames are in the area while you check for leaks. Sparks or open flames will result in a fire or explosion, damage to property, serious bodily injury, or death. LEAK TESTING: 1, Make 2-3 oz. of leak detection solution by mixing one part liquid dishwashing soap with three parts water.
Operating (continued) LIGHTING CAUTION: Keep the outdoor gas appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. CAUTION: Do NOT obstruct the flow of combustion and ventilation air. CAUTION: Check and clean burner/venturi tubes for insects and insect nests. A clogged tube can lead to a fire. 1. Make sure all labels, packaging and protective films have been removed from the outdoor fire pit. 2. Control knob must be in the “OFF” position (Figure 1). 3.
Maintenance Storage between uses: □ Turn the control knob to “OFF” position. □ Disconnect LP source. □ Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). □ If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages. NOTE: Wait until heater is cool before covering. Storage during periods of extended inactivity or when transporting: □ Turn the control knob to “OFF” position.
Troubleshooting PROBLEM PROBLEM CAUSE SOLUTION The flame and heat are low when the valve is turned to high. The propane lighting procedure was not followed correctly. Ensure lighting procedure is followed carefully. The valve must be in the off position when the tank valve is turned on. Turn the tank on slowly to allow pressure to equalize. See Lighting Instructions in the Operating section. Burners burn with yellow flame, accompanied by the smell of gas.
Life Gets Better With USE AND CARE GUIDE THD-E02GF0701-059-01 h Questions, problems, missing parts? Before returning to the store, please contact our Customer Service THANK YOU We appreciate the trust and confidence you have placed in PHI VILLA through the purchase of our product. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
LIFE GETS BETTER WITH PHI VLLA Table of Contents Table of Contents 2 Pre-assembly Safety Information 2 Assembly Warranty Care And Maintenance What is Covered 2 2 What is Not Covered 2 3 4-5 6 Safety Information • Tighten each bolt firmly and properly. Do not completely tighten screws until all screws are started. • Some parts may contain sharp edges. Wear protective gloves as necessary. • Children under the age of 16 should not be engaged in the assembly, removal or disassembly of the product.
LIFE GETS BETTER WITH PHI VLLA Pre-assembly (continued) Assemble the item on a soft, non-abrasive surface, such as carpet or cardboard to avoid damaging the item. Seek assistance to assemble bulky or heavy items. NOTE: Identify all parts packed in the carton against the parts list. Remove all the protective material carefully and DO NOT use a knife to prevent scratching the furniture. TOOLS REQUIRED NOTE: Hardware not shown to actual size.
LIFE GETS BETTER WITH PHI VLLA Assembly G A 1 E B C 2 F G D 4
LIFE GETS BETTER WITH PHI VLLA Assembly G 3 F D D 4 5
LIFE GETS BETTER WITH PHI VLLA Cleaning and Maintenance ● Clean the furniture with damp cloth, rinse thoroughly. Dry frame parts completely. Do not use bleach, acid or other solvents on the wicker or metal parts. ● We recommend the use of furniture covers to protect the table when not in use. ● Inspect and tighten all SCREW on a regular basis to ensure proper performance and safety.
