User Manual 150Mbps Wireless N ADSL2/2+ Modem Router FD-364N User Manual / V2.
Copyright Statement PHICOMM is the registered trademark of Shanghai Feixun Communication Co., Ltd. Other trademark or trade name mentioned herein are the trademark or registered trademark of the company. Copyright of the whole product as integration, including its accessories and software, belongs to Shanghai Feixun Communication Co., Ltd. Without the permission of Shanghai Feixun Communication Co., Ltd., individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router CONTENTS Chapter 1: Introduction .............................................. 1 Product Overview ............................................................................................... 1 Main Features ....................................................................................................... 2 Chapter 2: Hardware Installation ................................... 3 Front Panel .....................................................
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router NAT............................................................................................................................................ 31 ADSL ......................................................................................................................................... 33 QoS ............................................................................................................................................
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Chapter5: Specification ............................................ 49 Appendix A: Troubleshooting ..................................... 50 Appendix B: Certification .......................................... 52 FCC Statement .................................................................................................. 52 CE Mark Warning .............................................................................................
150Mbps Wireless N ADSL2/2+ Modem Router www.phicomm.com Chapter 1: Introduction Product Overview Thank you for choosing PHICOMM FD-364N Wireless N ADSL2+ Modem Router. This product is designed to provide a simple and cost-effective ADSL internet connection for a private Ethernet network. It is connected to network devices via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Main Features Complies with IEEE 802.11n to provide a wireless data rate of up to 150Mbps Provides 1 RJ11 DSL port, 4 RJ45 LAN ports Up to 24Mbps downstream speed Reach of 6.
150Mbps Wireless N ADSL2/2+ Modem Router www.phicomm.
www.phicomm.
150Mbps Wireless N ADSL2/2+ Modem Router www.phicomm.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the FD-364N. Step 3: Attach the power adapter. Connect the AC power adapter to the PWR connector on the rear of the device and plug in the adapter to a wall outlet or power extension. Step 4: Turn on your computers and power on the Modem Router.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Chapter 3: Quick Installation Configure Your PC After you directly connect your PC to FD-364N or a Hub/Switch which has connected to the Wireless Modem Router, we suggest you set your computer to obtain IP address automatically. For Windows XP/2000 1) Click Start > Control Panel.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router 2) Select and double click Network Connections. 3) Right click Local Area Connection and then select Properties.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router 4) Select Internet Protocol (TCP/IP) and click Properties. 5) Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router For Windows Vista/7 1) Click Start>Control Panel. 2) Click Network and Internet.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router 3) Click Network and Sharing Center. 4) Go to Change Adapter Settings (win7)/Manage Network Connections (Vista).
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router 5) Right click Local Area Connection, choose Properties. 6) Select Internet Protocol Version 4 (TCP/IPv4) and click Properties.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router 7) Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. Install Your Modem Router To configure the device, you can either run the Resource CD or run the Web based Setup Wizard. For first-time installation we recommend running the Resource CD, follow the step-by-step instructions to finish the installation.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Step 3: Go to Quick Start tab, and then click RUN WIZARD. Step 4: Click NEXT. Step 5: If you want to change the login password, put in the new password in this page. Otherwise just leave it blank, and then click NEXT.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Step 6: Choose your time zone, and then click NEXT. Step 7: Choose the connection type provided by your ISP (take PPPoE/PPPoA as an example here), and then click NEXT. Step 8: Put in Username, Password, VPI, VCI and Connection Type provided by your ISP. If you are not sure about the information, please confirm with your ISP. Then click NEXT.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Step 9: Click NEXT. Step 10: Click CLOSE. Note: Wait a moment, if the configuration is successful, the Internet LED light will finally turn green. The Internet light will not light on if the Wireless Modem Router works as bridge, please set up a broadband connection on your computer in that condition.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Chapter 4: Software Configuration This User Manual recommends using the Quick Installation Guide for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web based Setup Wizard. After your successful login, you can configure and manage the device.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Internet ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QoS to setup each PVC traffic priority.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router 1. Dynamic IP· Select this option if your ISP provides you an IP address automatically. This option is typically used for Cable services. Please enter the Dynamic IP information accordingly. Encapsulation: Select the encapsulation mode for the Dynamic IP Address, it is provided by your internet service provider. Bridge Interface: Activate the option, and the Router can also work in Bridge mode.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router 2．Static IP Select this option if your ISP provides static IP information to you. You should set Static IP Address, IP Subnet Mask, and Gateway on the screen below. Note: Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The Router will not accept the IP address if it is not in this format.
www.phicomm.com 3. 150Mbps Wireless N ADSL2/2+ Modem Router PPPoA/PPPoE Select this option if you have a username and password to access internet. This option is typically used for DSL services. Select Dynamic to obtain an IP address automatically for your PPP connection. Select Static to use a static IP address for your PPP connection. Please enter the information accordingly. Username: Enter your username for your PPPoA/PPPoE connection. Password: Enter your password for your PPPoA/PPPoE connection.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Static/Dynamic IP Address: For PPPoA/PPPoE connection, you need to specify the public IP address for this ADSL Router. The IP address can be either dynamically (via DHCP) or given IP address provided by your ISP. For Static IP, you need to specify the IP address, Subnet Mask and Gateway address. Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for WAN interface, including RIP1, RIP2-B and RIP2-M.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router LAN Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as private settings. You may change the LAN IP address if necessary. The LAN IP address is private to your internal network and cannot be seen over internet. IP Address: Enter the Router’s local IP Address, then you can access to the Web based Setup Wizard via the IP Address, the default value is 192.168.1.1.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router DHCP: Select Enabled, then you will see the screen. The Router will work as a DHCP server, it becomes the default gateway for DHCP clients connected to it. DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives out IP addresses when a device is booting up and request an IP address to be logged on to the network. That device must be set as a DHCP client to obtain the IP address automatically. By default, the DHCP Server is enabled.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Server IP: Enter the DHCP server IP address runs on WAN side. Note: If you select Disabled, the DHCP function will not take effect. DHCP Relay may be no use if default route is not dynamic or static routing mode! Add DHCP Reservation: Assign a static IP for some certain computer. DHCP Clients List: Show the current clients’ information which are connected to this Wireless Modem Router.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Channel: Select the channel you want to use from the drop-down List of channel. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Beacon Interval: Enter a value between 20-1000 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router SSID: Refer to your wireless network name, you can change it to anything you want. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters. Make sure this setting is the same for all stations in your wireless network. Type the desired SSID in the space provided.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Note: • This feature is available only when OPEN, WPA-PSK, WPA2-PSK or WPA/WPA2-PSK mode is configured. • To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function meanwhile.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Wireless MAC Address Filter: Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius. To filter wireless clients by MAC Address, either deny or allow access. If you do not wish to filter users by MAC Address, select Deactivated. Active: Used to enable or disable this wireless Mac filter function.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Firewall Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack. SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side. Routing Click ADD ROUTE button to add a new route on the next screen.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Router; over Internet (WAN), the gateway must be the IP address of one of the remote nodes. Metric: Metric represents the cost of transmission for routing purposes.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router DMZ Host IP Address: Enter the specified IP Address for DMZ host on the LAN side. Note: For security reasons, you should avoid using the default DMZ server feature. When a computer is designated as the default DMZ server, it loses much of the protection of the firewall, and is exposed to many exploits from the Internet. If compromised, the computer can be used to attack your network.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Local IP Address: Enter the IP Address for the virtual server in LAN side. Virtual Server Listing: This displays the information about the virtual servers you establish. ADSL You can select the ADSL Mode and ADSL Type on the next screen. The ADSL feature can be selected when you meet the physical connection problem. Please confirm the settings with your Internet Service Provider.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router QoS: Select this option to Activate/Deactivate the IP QoS on different types. Discipline: Choose WRR or Strict Priority WRR weight: Set the priority weight. Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Wireless Modem Router will take the corresponding action to deal with it. Rule Index: Select the index for the rule you want to configure.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router well as differentiated Internet services by giving network resource and usage control to the network operator. IP Precedence Range: Enter the IP precedence range that the Router takes to differentiate the traffic. Type of Service: Select the type of service that the Wireless Modem Router takes to deal with the traffic. DSCP Range: Enter the DSCP range to differentiate the traffic. 802.1p: Select the priority range for the rule.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router PortBinding Active: To active or deactive this function. Group Index: Show the index of rules. ATM VCs & Ethernet & WLan: Choose the PVCs, Ethernet port, WLan that controlled by the rule. PortBinding Summary: Display the summary of PortBinding. Access Management Choose Access Management, you can see six submenus. Click any of them, and you will be able to configure the corresponding function.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router SNMP The SNMP (Simple Network Management Protocol) is used for exchanging information between network devices. Get Community: Set the password for the incoming get and get next requests from the management station. Set Community: Set the password for incoming set requests from the management station.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router DDNS The router offers a DDNS (Dynamic Domain Name System) feature. The feature lets you use a static host name with a dynamic IP address. Please type the host name, user name and password assigned to your ADSL Router by your Dynamic DNS provider. User also can decide to turn on DDNS Wildcard or not. Dynamic DNS: Activate the DDNS function or not. Service Provider: This field displays the service provider of DDNS.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router ACL You can specify the client to access the ADSL Router once setting its IP as a Secure IP Address through selected applications. ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router. ACL Rule Index: Select the ACL rule index for the entry. Active: Enable the ACL rule.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Filter The filtering feature includes IP/MAC Filter, Application Filter and URL Filter. The feature makes it possible for administrators to control user's access to internet, protect the networks. Filter Type Selection: Select the filter type for the configuration below. Rule Type Selection: White list and black list. IP/MAC Filter Rule Index: Select the Set index for the IP Filter entry.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Protocol: TCP, UDP or ICMP in the drop-down list for the connection between the Source IP address and Destination IP address. IP/MAC Filter Listing: This displays the information about the IP Filter rules. CWMP The router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto-Configuration Server).
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Path: Enter the path that connects to the ACS server. User Name/Password: Enter the User Name and Password that provided the ACS server to login the router. Periodic Inform: Activate or deactivate the function. If Activated, the information will be informed to ACS server periodically. Interval: Enter the interval time here. Maintenance Choose Maintenance, you can see five submenus.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router NTP server is set, you will only need to set the time zone. If PC’s Clock is selected, the device will get the PC’s Clock by way of the system time. 1. NTP Server automatically Select NTP Server automatically as the synchronize time, please choose the time zone. Note: The ADSL Router built-in some NTP Servers, when the Wireless Modem Router connects to internet, it will get the system time automatically from the NTP Server.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router 3. Manually Select Manually as the synchronize time, please configure the date and time corresponding to the current time. File Upgrade You can upgrade the firmware of the Router in this page. Make sure the firmware or config file you want to use is on the local hard drive of the computer. Click Browse to find the local hard drive and locate the firmware or config file to be used for upgrade.
www.phicomm.com • 150Mbps Wireless N ADSL2/2+ Modem Router When you upgrade the router's firmware, you may lose its current configurations, so please back up the router’s current settings before you upgrade its firmware. • Do not turn off the router or press the Reset button while the firmware is being upgraded. • The router will reboot after the upgrading has been finished.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router SysRestart You can select to restart the device with current settings or restore to factory default settings in this page. Diagnostic You can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in this page. Status Choose Status, you can see three next submenus: Device Info, System Log and Statistics. Click any of them, and you will be able to configure the corresponding function.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Device Info You can view the device information, including LAN, WAN and ADSL in this page. The information will vary depending on the settings of the Wireless Modem Router configured on the Interface Setup screen. Note: Click the other submenus System Log or Statistics in figure above, you will be able to view the system log and traffic statistics about the Wireless Modem Router.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router System Log You can query the logs of the Wireless Modem Router in this page. Statistics You can view the network traffic over network in this page. Interface: You can select Ethernet, ADSL and WLAN to view the corresponding network traffic over different ports.
150Mbps Wireless N ADSL2/2+ Modem Router www.phicomm.com Chapter5: Specification Basic Standards IEEE 802.11n ,IEEE 802.11g, IEEE802.11b, IEEE802.3, 802.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router Appendix A: Troubleshooting 1. How do I restore my Wireless Modem Router’s configuration to factory default settings? With the router powered on, press the Reset button on the rear panel, keep holding it for about 5 seconds then release it. 2. Why I cannot login the Wireless Modem Router’s web management page? • Make sure the computer goes into the LAN port of the router.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router make sure the VPI/VCI, Connection Type, username and pass word are correct. If there are any mistakes, please correct the settings and try again. 6. The computer cannot connect to the internet wirelessly. Please make sure you can access the Internet when plug in the Ethernet cable from the Wireless Modem Router to the computer, otherwise, please refer to Question 4.
150Mbps Wireless N ADSL2/2+ Modem Router www.phicomm.com Appendix B: Certification FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
150Mbps Wireless N ADSL2/2+ Modem Router www.phicomm.com • This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. CE Mark Warning Marking with the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
150Mbps Wireless N ADSL2/2+ Modem Router www.phicomm.com Appendix C: Glossary ATM (Asynchronous Transfer Mode): ATM is a cell based transfer mode that requires variable length user information to be segmented and reassembled to/from short, fixed length cells. It uses two different methods for carrying connectionless network interconnect traffic, routed and bridged Protocol Data Units (PDUs), over an ATM network.
www.phicomm.com 150Mbps Wireless N ADSL2/2+ Modem Router VCI (Virtual Channel Identifier): The identifier of the VC contained in the ATM cell header. VPI (Virtual Path Identifier): The identifier of the VP contained in the ATM cell header. VLAN (Virtual Local Air Network): Logical subgroups that constitute a Local Area Network (LAN). This is done in software rather than defining a hardware solution.
Shanghai Feixun Communication Co., Ltd. E-mail: support@phicomm.com Website: www.phicomm.com Copyright © 2011 Shanghai Feixun Communication Co., Ltd. All rights reserved.
