User Manual

ManualsBrandsPhidgets Manuals12V DC Wall AdaptersPhidgets Power Supply 12VDC 2.0A - EU

MODEL NO.

AG2412-E281

SHEET NO

ISSUED DATE:

JUL/06/2007

DESCRIPTION SWITCHING MODE

AC ADAPTER

REVISED DATE:

APPROVAL SIGNATURE

DATE:

CUSTOMER : Phidgets Inc.

Model :

AG2412-E281(2A0F) Phidgets REV.00

AC Input 100-240Vac DC Output 12V/2A PC / NP

DC O/P cable

2468 20# 2.1X5.5X9.5mm 180∘Tuning fork +Kink 6FT

AC plug EU 2Pin Packaging PE Bag

Jentec Technology Co., Ltd.

17F #2 Jian-Ba Rd., Chung-Ho City

Taipei Hsien , Taiwan.

Tel : 886-2-8226-2057

Fax: 886-2-8226-2077

www.jentec.com.tw

Summary of content (14 pages)

PAGE 1
MODEL NO. DESCRIPTION AG2412-E281 SWITCHING MODE AC ADAPTER SHEET NO ISSUED DATE: REVISED DATE: 1 JUL/06/2007 APPROVAL SIGNATURE DATE: CUSTOMER : Phidgets Inc. Model : AG2412-E281(2A0F) Phidgets AC Input REV.00 DC O/P cable 100-240Vac DC Output 12V/2A PC / NP 2468 20# 2.1X5.5X9.5mm 180∘Tuning fork +Kink 6FT AC plug EU 2Pin Jentec Technology Co., Ltd. 17F #2 Jian-Ba Rd., Chung-Ho City Taipei Hsien , Taiwan. Tel : 886-2-8226-2057 Fax: 886-2-8226-2077 www.jentec.com.
PAGE 2
MODEL NO.
PAGE 3
MODEL NO. DESCRIPTION AG2412-E281 SWITCHING MODE AC ADAPTER CONTAINS: INTRODUCTION 1.0 INPUT REQUIREMENTS 2.0 1.1 Voltage (VAC) 1.2 Frequency 1.3 In-Rush Current 1.4 Ac Input Current OUTPUT REQUIREMENTS 2.1 Output Power 2.2 Output Regulation 2.2.1 Input Voltage 2.2.2 Input Frequency 2.2.3 Static Load 2.2.4 Output Voltage 2.2.5 Ripple 2.3 Transient Response and Deviation 2.4 Turn on, Hold up Time 2.5 Efficiency 3.0 PROTECTION 3.1 Input Current 3.2 Output Voltage 3.
PAGE 4
MODEL NO. DESCRIPTION 6.2.2 AG2412-E281 SWITCHING MODE AC ADAPTER Relative Humidity 7.0 EMI EMISSIONS 8.0 SAFETY 8.1 Dielectric Strength (Hi-Pot) Test 8.2 Insulation Resistance 8.3 Leakage current 9.0 ENVIROMENTAL PROTECTION 10.0 11.0 12.0 13.0 9.1 RoHS and WEEE 9.
PAGE 5
MODEL NO. DESCRIPTION AG2412-E281 SWITCHING MODE AC ADAPTER 5 SHEET NO ISSUED DATE: REVISED DATE: JUL/06/2007 INTRODUCTION This documents specifies ONE voltage +12V power supply for electronic data processing equipment. The power supply will provide power to all system components. 1.0 INPUT REQUIREMENTS 1.1 Input Voltage Designing Range: 90~264 VAC. 1.2 Line Frequency Designing Range: 47 HZ to 63 HZ. 1.3 In-Rush Current: 30 A max. less under 115V conditions.
PAGE 6
MODEL NO. DESCRIPTION AG2412-E281 SWITCHING MODE AC ADAPTER SHEET NO ISSUED DATE: REVISED DATE: 6 JUL/06/2007 shown below when measured under constant load range of 0.01 ~2A with an oscilloscope with at bandwidth of 20MHz. TABLE 2.2.5 Output # Voltage 1 +12V Maximum peak to peak ripple and noise 120 mV NOTE: Test measurement will be made at the output connector on the power Supply output cord. With used an aluminum Electrolytic capacitor of 10uf and ceramic of 0.
PAGE 7
MODEL NO. AG2412-E281 SWITCHING MODE AC ADAPTER DESCRIPTION SHEET NO ISSUED DATE: REVISED DATE: 7 JUL/06/2007 4.0 MECHANICAL Introduction The power supply will provide Output power connector show as in Table 4.1 FRONT VIEW OF OUTPUT CONNECTOR Table 4.1 Pin out for DC Connector PIN # Output Voltage 4.2 General Requirements The power supply must not exceed an audible noise level of 32 dB while operating under any combination of specified load and input voltages and frequencies.
PAGE 8
MODEL NO. DESCRIPTION AG2412-E281 SWITCHING MODE AC ADAPTER SHEET NO ISSUED DATE: REVISED DATE: 8 JUL/06/2007 6.1.1 Ambient temperature: -25℃ ～ +85℃ 6.1.2 Relative Humidity: 10% ～ 95% 6.2 Operation The power supply shall be capable of operating continuously in any mode without performance deterioration in the following environmental conditions: 6.2.1 Ambient Temperature: 0℃ ～ 40℃ 6.2.2 Relative Humidity: 10% ～95%. 7.
PAGE 9
MODEL NO. DESCRIPTION AG2412-E281 SWITCHING MODE AC ADAPTER SHEET NO ISSUED DATE: REVISED DATE: 9 JUL/06/2007 11.
PAGE 10
MODEL NO. DESCRIPTION 12.
PAGE 11
MODEL NO. DESCRIPTION AG2412-E281 SWITCHING MODE AC ADAPTER 13.
PAGE 12
MODEL NO.
PAGE 13
MODEL NO.
PAGE 14
MODEL NO.