Operation Manual

19
EN
1A23
ADVANCED OPERATION
ADVANCED
OPERATION
4 Select “AUTOSCAN” using [K / L], then
press [OK].
AUTOSCAN
EXIT
CHANNEL
TIME
DETAIL
INITIAL
AUTOSCAN will rescan all channels.
This may take a while to complete.
BACK
AUTOSCAN
AUTOSCAN
The system is now scanning
12% Channel Found
EXIT
• STB starts receiving available digital channels and
stores them in the channel map.
• When the scanning is complete,
“AUTOSCAN COMPLETED” will be indicated.
• After autoscan is complete, press [CH / ] to
verify whether STB is receiving channels
properly.
To cancel during scanning:
Press [SETUP] or [OK].
NOTE:
•
If canceled, some channels not yet scanned may not
be received. We recommend completing autoscan.
• When you want to completely refresh the channel
map, delete all the channels, then do the autoscan
again. See “Adding/Deleting Channels” on page 17
for details.
When “NO SIGNAL” appears on the screen:
Verify the antenna connection, then scan again.
The STB tunes in channel 2-1 and “NO SIGNAL”
appears if the STB could not receive any channels.
Selecting RF OUT Channel
If you want to enjoy analog TV channels also, you
must set the RF out channel.
1 Press [SETUP] to display “SETUP”
menu.
2 Select “CHANNEL” using [K
/ L], then
press [OK].
3 Select “RF OUT” using [K
/ L], then
press [OK].
4 Select the desired setting using [K
/ L],
then press [OK].
Default setting is “CH3”.
Switch RF OUT.
If the screen doesn’t show anything
after switching RF OUT, set the TV
Channel to CH3, then hold down a
“SETUP”button for 3 seconds.
CH3
RF THROUGH
CH4
E.g., switching from CH3/CH4
output to RF THROUGH
Switch RF OUT.
CH3
RF THROUGH
CH4
If the screen doesn’t show anything
after switching RF OUT, then hold
down a “SETUP”button for 3
seconds.
E.g., switching from RF
THROUGH to CH3/CH4 output
• Select “RF THROUGH” if...
- you want to receive and view the analog TV
channels on your TV. (The STB’s power must be
on.) Switch your TV’s channel from the video
input channel (ch3 or ch4) to the analog channel
to view the analog TV channels.
• Select “CH3” or “CH4” if...
- you want to view the digital TV channels output
through the STB on your TV. (You also can
switch between “CH3” and “CH4” by holding
[SETUP] down over 3 seconds.) Then tune your
TV to the corresponding external input channel
(ch3 or ch4). Refer to your TV’s manual for
details.
5 Using [s / B], select “YES” if you like
to proceed. Select “NO” if you want to
cancel. Then, press [OK].
E.g., switching from CH3/CH4
output to RF THROUGH
RF OUT is RF THROUGH
Are you sure ?
YES
NO
If the screen doesn’t show
anything after switching
RF OUT, set the TV Channel
to CH3, then hold down a
“SETUP”button for 3 seconds.
6 Press [SETUP] to exit “SETUP” menu.
NOTE:
•
If the screen doesn’t show anything after making a
selection, tune your TV to ch3 and then switch the
RF out setting by holding down [SETUP] over 3
seconds.
• RF cable connection is required for receiving
analog TV signal. Refer to “Connecting to TV” on
page 10.
• To view analog TV channels through the STB, the
STB must be turned on.
X6032UD_Book.indb 19X6032UD_Book.indb 19 11/28/2007 4:34:40 PM11/28/2007 4:34:40 PM