User's Manual

ManualsBrandsPhilio Technology ManualsElectronicsSmart Dimmer Socket

PAD02

Z-Wave Smart Dimmer Socket

Warning: Do not use Non-Dimmable LED lamps.

PAD02 is an E27(EU)/ E26(US) Edison screw based lamp socket, which provides

electrical connection to the E14(EU)/ E12(US) Edison screw based lamps and

support it in the lighting fixture. The use of socket allows lamps to be safely and

conveniently replaced. You can On/Off the light by pressing the button briefly,

or a long pressing to control the brightness of dimmable light bulb.

This dimmer is a transceiver which is a security enabled device which based on

Z-Wave Plus technology, and it is fully compatible with any Z-Wave

enabled

network. Since PAD02 supports Security Command Class, it can learn with

Secured controller. Its functionality and supported command classes is identical

when included as a secure and non-secure device.

Adding to Z-Wave

Network

In the front casing, there is an on/off button with LED indicator below which is used to

switch on and off or carries out inclusion, exclusion, reset or association.

When first power applied, its LED flashes on and off alternately and repeatedly at 0.5

second intervals. It implies that it has not been assigned a node ID and start auto

inclusion.

Auto Inclusion

The function of auto inclusion will be executed as long as the dimmer does not

have Node ID and just connect the switch to main power.

Note: Auto inclusion timeout is 2 minute during which the node information of

explorer frame will be emitted once every several seconds. Unlike “inclusion” function

as shown in the table below, the execution of auto inclusion is free from pressing the

On/Off button on the dimmer.

The table below lists an operation summary of basic Z-Wave functions. Please refer

to the instructions for your Z-Wave

Certificated Primary Controller to access the

Setup function, and to include/exclude/associate devices

Function Description Annotation

No node ID The Z-Wave Controller does not allocate

a node ID to the Switch.

LED 2-second on, 2-second

off

Inclusion 1. Put your Z-Wave controller into

inclusion mode by following the

instructions provided by the

controller manufacturer.

One press one flash LED

2. Pressing Include button of PAD02

three times within 2 seconds will

enter inclusion mode.

Summary of content (5 pages)

PAGE 1
switch on and off or carries out inclusion, exclusion, reset or association. PAD02 When first power applied, its LED flashes on and off alternately and repeatedly at 0.5 second intervals. It implies that it has not been assigned a node ID and start auto Z-Wave Smart Dimmer Socket inclusion. Auto Inclusion The function of auto inclusion will be executed as long as the dimmer does not have Node ID and just connect the switch to main power.
PAGE 2
Exclusion 1. Put your Z-Wave controller into One press one flash LED 2. There are only one group for the exclusion mode by following the switch instructions provided by the Including a node ID allocated by Z-Wave Controller means inclusion. controller manufacturer. ID allocated by Z-Wave Controller means exclusion. 2. Pressing Include button of PAD02 Failed or success in including/excluding the node ID can be viewed from the Z-Wave three times within 2 seconds will enter Controller.
PAGE 3
. Do not locate the dimmer where exists combustible substances or any source of US TYPE: PAD02-2 heat, e.g. fires, radiators, boiler etc. 4. After putting it into use, the body of dimmer will become a little bit hot of which phenomenon is normal.
PAGE 4
Troubleshooting Operating Temperature 0°C ~ 40°C Frequency Range 868.40MHz & 869.85MHz/ EU (PAD02-1); 908.4MHz & 916.0MHz/ USA (PAD02-2); Symptom Cause of Failure Recommendation RF Maximum Power +5dBm The Switch not working 4. The Switch is not 1. Check power connections Transmission Range Minimum 40 m in door 100m outdoor line of sight and LED off 2. Don’t open up the Switch and send it Modulation Type FSK (Frequency-Shift Keying) plugged into the electrical outlet properly for repair.
PAGE 5
• Connect the equipment into an outlet on a circuit different from that to which the receiver is Disposal This marking indicates that this product should not be disposed with connected. other household wastes throughout the EU. To prevent possible harm to • Consult the dealer or an experienced radio/TV technician for help. the environment or human health from uncontrolled waste disposal, This device complies with Part 15 of the FCC Rules.