User Manual

ManualsBrandsPhilio Technology ManualsElectronicsSmart Energy In wall Switch

PAN03-1/-2/-3

Smart Energy In wall Switch Module

Fig 1. Assembling

This in-wall dual relay switch module is a transceiver which is a Z-WaveTM enabled

device and is fully compatible with any Z-WaveTM enabled network. Mini size design

let the module can easily hide itself into the wall box and that will be good for the

house decoration.

There are many kind of application by using the module to switch AC power On and

Off , one main application is the light control. The new smart relay calibration

technology can reduce the inrush current caused by the load and let the module work

perfectly with many kind of light like incandescent, fluorescent and LED light.

This in-wall switch module is able to detect Instant power c (5~2500W)(11Ampere)

and overload wattage (2700~2800W)(12 Ampere) of connected light or appliances.

When detecting overload state, the Module will be disabled and its On/Off button will

be lockout of which LED will flash quickly. However, disconnect and re-connect the

Module will reset its overload condition to normal status.

Adding to Z-Wave

Network

In the front casing, there is an on/off button with LED indicator below which is used to

toggle switch on and off or carry out inclusion, exclusion, reset or association. When

first power is applied, its LED flashes on and off alternately and repeatedly at 2-

second intervals. It implies that it has not been assigned a node ID and cannot work

with Z-Wave enabled devices.

Auto Inclusion

The function of auto inclusion will be executed as long as the in wall switch does not

have Node ID and just connect the switch to main power.

Summary of content (10 pages)

PAGE 1
PAN03-1/-2/-3 Smart Energy In wall Switch Module house decoration. There are many kind of application by using the module to switch AC power On and P Off , one main application is the light control. The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent, fluorescent and LED light.
PAGE 2
Note: Auto inclusion timeout is 4 minute during which the node information of Reset 1. Pressing INCLUDE_BUTTON three explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as times within 1.5 seconds will enter shown in the table below, the execution of auto inclusion is free from pressing the inclusion mode. On/Off button on the Switch. 2. One press one flash Within 1 second, press On/Off button again for 5 seconds until LED is off.
PAGE 3
button or RF command , the LED will lights up 1 second and then off. No node ID Under normal operation, when the Switch has not been allocated a node ID, the LED flashes on and off alternately at 2-second intervals. By pressing S1 S2 or On/Off button, it will stop flashing temporarily. However, after disconnect and reconnect the Switch, the LED will flash on and off alternately at 2-second intervals.
PAGE 4
Basic Get Command: [Command Class Basic, Basic Get] 4. To manually turn OFF the Switch, simply press and release the On/Off button. Basic Report Command: The LED will light ON for 1 second and the load plugged into the Switch will turn Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)] OFF. Report ON:[Command Class Basic, Basic Report, Value = (255)0xFF] Binary Switch Get Command:[Command Class Switch Binary, Switch Programming Binary Get] Binary Switch Report Command: 1.
PAGE 5
When the power consumption of load vary over 5%, it will send Meter report to the nodes of Grouping 1. 2. Z-Wave’s Groups (Association Command Class Version 1) Meter Report Command: [Command Class Meter，Meter Report，scale(bit 2) +Rate Type +Meter Type，Precision + Scale(bit 1,0)+ Size，Meter Value 1，Meter Value 2，Meter Value 3，Meter Value 4] The Switch can be set to send reports to control associated Z-Wave devices. It supports one association group with one node support for Grouping 1.
PAGE 6
Rate Type = 0x01 Meter Type = 0x01 Precision = 1 Scale = 0x02(W) Rate Type = 0x01 Size = 4 Bytes (Meter Value) Meter Type = 0x01 Meter Value 1 = (W) MSB Precision = 2 Meter Value 2 = (W) Scale = 0x00 (KWh) Meter Value 3 = (W) Size = 4 bytes (Meter Value) Meter Value 4 = (W)LSB Meter Value 1 = (W) MSB Meter Value 2 = (W) Example: Meter Value 3 = (W) Meter Value 1 = 0x00 (W) Meter Value 4 = (W) LSB Meter Value 2 = 0x00 (W) Meter Value 3 = 0x03 (W) Example: Meter Value 4 = 0xEA (W) Scale = 0
PAGE 7
2-2-3 Clearing accumulated power consumption Example: Scale = 0x04 (V) Precision = 1 Meter Reset Command: [Command Class Meter, Meter Reset] Size = 2 (2 Bytes of V) Meter Value 1 = 0x09(V) Meter Value 2 = 0x01(V) 2-2-4 AC load Voltage (V) AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V) When receiving Meter Get Command, it will report Meter Report Command to the node asked.
PAGE 8
Meter Value 1 = High Byte (I) Scale = 0x06(PF) Meter Value 2 = Low Byte (I) Size = 1 Bytes Meter Value 1 Example: Scale = 0x05 (I) Example: Precision = 2 Scale = 0x06 (PF) Size = 2 (2 Bytes of I) Precision = 2 Meter Value 1 = 0x01(I) Size = 1 (1 Byte of PF) Meter Value 2 = 0x21(I) Meter Value 1 = 0x63(PF) AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A) Load power factor (PF) = Meter Value 1 =0.
PAGE 9
The Switch LED 4. Command Classes 1. Not carry out illuminating, but the association Detector cannot control 1. Carry out association 2. Wait for a while to re-try 2. Same frequency The Switch supports Command Classes including… the Switch * COMMAND_CLASS_SWITCH_BINARY LED keep flashing 30 * COMMAND_CLASS_BASIC seconds, but cannot control interference Overload occurs * COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 Remove the load attached or check max.
PAGE 10
Warning: If this equipment does cause harmful interference to radio or television reception, which 1.Plug out to disconnect from power supply; Do not plug in line. can be determined by turning the equipment off and on, the user is encouraged to try to cor- 2. Do not exceed the max rating rect the interference by one of the following measures: • Reorient or relocate the receiving antenna. Disposal • Increase the separation between the equipment and receiver.