User Manual

ManualsBrandsPhilio Technology ManualsElectronicsIn Wall Switch

Slim Multi-Sensor PSM02

The slim multi-sensor PSM02 has PIR, door/window, temperature and

illumination, 4 sensors function in one, based on Z-Wave

technology.

Z-Wave

is a wireless communication protocol designed for home

automation, specifically to remotely control applications in residential

and light commercial environments. The technology uses a low-power

RF radio embedded or retrofitted into home electronics devices and

systems, such as lighting, home access control, entertainment systems

and household appliances.

This device is one component of the Z-Wave

sensor system and is

designed to work with all other Z-Wave

enabled devices in a home

control network. The device adopt the Z-Wave

400 series chip, when

your Z-Wave

network system is all made by Z-Wave

400 series

devices. The network system will have the advantages as below.

• Concurrent multi-channel support reduces external interference.

• Better RF range, improve about 10 meters in indoor.

• Support 100 Kbps transmit speed, speed up communication.

Adding to Z-Wave

Network

There are two tamper keys in the device, one is in the back side,

another is in the front side. They have the same function. Both of them

can inclusion, exclusion, reset or association from Z-Wave

network.

In the first time, add the device into the Z-Wave

network. First, make

sure the primary controller is in the inclusion mode. And then power on

the device, just take out the insulation Mylar in the back side of the

device. The device will auto start the NWI (Network Wide Inclusion)

mode. And it should be included in 5 seconds. You will see the LED

light ON one second.

Function

Description

Inclusion

1. Have Z-Wave

Controller entered inclusion mode.

2. Pressing tamper key three times within 1.5 seconds

will enter inclusion mode.

3. After inclusion successful, the device will wake to

receive the setting command from Z-Wave

Controller about 20 seconds.

Exclusion

1. Have Z-Wave

Controller entered exclusion mode.

2. Pressing tamper key three times within 1.5 seconds

will enter exclusion mode.

Node ID has been excluded.

Reset

1. Pressing tamper key four times within 1.5 seconds

and do not release the tamper key in the 4

pressed, and the LED will turn ON.

2. After 3 seconds the LED will turn OFF, after that

within 2 seconds, release the tamper key. If

successful, the LED will light ON one second.

Otherwise, the LED will flash once.

3. IDs are excluded and all settings will reset to

factory default.

Summary of content (10 pages)

PAGE 1
Adding to Z-WaveTM Network Slim Multi-Sensor PSM02 There are two tamper keys in the device, one is in the back side, another is in the front side. They have the same function. Both of them can inclusion, exclusion, reset or association from Z-WaveTM network. In the first time, add the device into the Z-WaveTM network. First, make sure the primary controller is in the inclusion mode. And then power on the device, just take out the insulation Mylar in the back side of the device.
PAGE 2
Z-WaveTM Message Report 1. Have Z-WaveTM Controller entered association mode. 2. Pressing tamper key three times within 1.5 seconds will enter association mode. Association Note: The device support 2 groups. The group 1 is for receiving the report message, like triggered event, temperature, illumination etc. The group 2 is for light control, the device will send the “Basic Set” command to this group. • Including a node ID allocated by Z-WaveTM Controller means inclusion.
PAGE 3
nodes in the group 1. The device will measure the temperature in every 64 seconds. And if the temperature is over 140 degree Fahrenheit (60 degree Celsius), the device also report in each measurement. * PIR Warm Up When the power on, the PIR need to warm up before operation. The warm up time about 1 minute, the LED will flash in every 2 seconds. After finish the procedure the LED will light ON three times.
PAGE 4
There are three modes “Test”, “Home Automation” and “Security”. “Test Mode” is for the user test the sensor function when installation. “Home Automation Mode” focus in automatic to control the lighting equipment. For convenience and save energy. “Security Mode” focus in surveillance, warning. When the event triggered, normally the LED won't indicated, unless the battery is in the low level, the LED will flash once. And in the “Test Mode” the LED also will light ON one second.
PAGE 5
PAGE 6
Battery Installation When the device report the low battery message. The user should replace the battery to new one. The way to open the front cover please follow below steps. 1. Using a tool like (1) to press 1-1 till hear a click sound 2. Hold the front cover and pull back 3. Hold the front cover and pull up Choosing a Suitable Location 1. The recommended mounting height is 160cm 2. Don't let the device facing the window or the sunlight. 3. Don't let the device facing the source of heat. Like heater.
PAGE 7
Installation After finish the test and decide to fix, then you can remove tape A, and mounting the sensor by using tape B. This will close the tamper key and let the sensor enter normal mode. 1. In the first time, add the device into the Z-WaveTM network. First, make sure the primary controller is in the inclusion mode. And then power on the device, just take out the insulation Mylar in the back side of the device. The device will auto start the NWI (Network Wide Inclusion) mode.
PAGE 8
0 means disable the PIR motion. 1 means the lowest sensitivity, 99 means the highest sensitivity. High sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re-trigger too frequency. 4 Light Threshold 99 0: Fahrenheit, 1:Celsius Bit4: Disable illumination report after event triggered. Bit5: Disable temperature report after event triggered. Setting the illumination threshold to turn on the light.
PAGE 9
Z-Wave Supported Command Class time. 8 seconds per tick, and minimum time is 24 seconds, default tick is 3 (24 seconds). Setting the suitable value to prevent received the trigger signal too frequency. Also can save the battery energy. Notice: If this value bigger than the configuration setting NO. 9. There is a period after the light turned off and the PIR not detecting.
PAGE 10
Limited Warranty • Philio Technology Corporation product is warranted against defects in material and workmanship for two years. Philio Technology Corporation will replace it free of charge and does not issue any refunds. This warranty extends only to wholesale customers who buy through Philio Technology Corporation authorized distribution channels. Philio Technology Corporation does not warrant this product to consumers.