Cut Sheet
LED-INTA-0024V-41-F-O
Brand Name XITANIUM
Description 100W 24V 4.1A
Input Voltage 120~277
Input Frequency 50/60Hz
RoHS Yes
Status Active
Revised 12/14/2010
PHILIPS LIGHTING N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Installation & Application Notes:
Section I – Physical Characteristics
1.1 LED Driver shall be installed inside an electrical enclosure
1.2 Wiring inside electrical enclosure shall comply with 600V/105°C rating or higher.
Section II – Performance
2.1 LED Driver is UL Class 2 power unit as per UL1310. It is also listed in the UL Sign Accessory Manual (UL
SAM).
2.2 LED Driver has Class A sound rating.
2.3 LED Driver has a minimum operating ambient temperature of -40°C.
2.4 LED Driver has a life expectancy of 50,000 hours at Tcase of ≤ 80°C.
2.5 LED Driver has a life expectancy of 100,000 hours at Tcase of ≤ 70°C.
2.6 LED Driver has a typical self rise of 30°C at maximum load in open air without heat sink.
2.7 LED Driver is certified by UL for use in a dry or damp location (Outdoor Type I).
2.8 LED Driver tolerates sustained open circuit and short circuit output conditions without damage.
2.9 LED Driver maximum allowable case temperature is 90°C – see product label for measurement location.
2.10 LED Driver reduces output power to LEDs if maximum allowable case temperature is exceeded.
2.11 LED Driver has a failure rate of ≤ 0.01% per 1,000 hours.
2.12 LED Driver complies with FCC rules and regulations, as per Title 47 CFR Part 15 Non-Consumer (Class A).
2.13 LED Driver conforms to EN61558-1, EN 61558-2-17 and EN 60065.
Section III – UL Conditions of Acceptability (File E220165)
When installed in the end product, consideration shall be given to the following:
3.1 These LED Drivers have been evaluated to comply with Class 2 output criteria.
3.2 These LED Drivers are only suitable for use in Dry and Damp locations.
3.3 These products are rated as follows:
I
nput, 60 Hz.
O
UTPUT V@Amperes
DC
Model
V
olt/V Amp/
A
P
ower/W
LEDINTA0024V41DLO
120-
2
77
0
.95
-
0
.40
1
00
2
4V@4.1(*)
LED-INT
A
-0024V-41-F
-
LO 120-
2
77
0
.95
-
0
.40
1
00
2
4V@4.1 (*)
LEDINTA0024V41FO 120-
2
77
0
.95
-
0
.40
1
00
2
4V@4.1(*)
LED-INT
A
-0024V-30-F
-
LO 120-
2
77
0
.72
-
0
.32
7
2
2
4@3.0 (**)
LED-INT
A
-0024V-30-D
-
LO 120-
2
77
0
.72
-
0
.32
7
2
2
4@3.0 (**)
LED-INT
A
-0024V-20-F
-
LO 120-
2
77
0
.48
-
0
.22
4
8
2
4@2.0 (***)
LED-INT
A
-0024V-20-D
-
LO 120-
2
77
0
.48
-
0
.22
4
8
2
4@2.0 (***)
LEDINTA0024V32FO
120-
2
77
0
.75
-
0
.35
7
7
2
4@3.2 (+)
LEDINTA0024V22FO
120-
2
77
0
.50
-
0
.25
5
3
2
4@2.2 (++)
(*) - For connection to LED array consisting of 100 Watt maximum.
(**) - For connection to LED array consisting of 72 Watt maximum.
(***) - For connection to LED array consisting of 48 Watt maximum.