User's Manual

ManualsBrandsPhilips Consumer Electronics ManualsElectronicsUS DECT BASE UNIT

Toggle between calls

Press int to switch between the outside call

and the intercom call.

Transfer a call

Press int during a call.

2 Select or enter the handset number, then

press [SELECT] to conrm.

3 Press END when the other side answers

your call.

The call is now transferred to the »

selected handset.

Make a conference call

A 3-way conference call is a call between you,

another handset user and the outside callers. It

requires two handsets to share the same base

station.

During an external call

1 Press int to initiate an internal call.

The handsets available for intercom are »

displayed.

The external caller is put on hold. »

2 Select or enter a handset number, then

press [SELECT] to conrm.

The selected handset rings. »

The intercom is established. »

3 Press and hold int on your handset.

You are now on a 3-way conference »

call with the external call and the

selected handset.

4 Press END to end the conference call.

5 Intercom and

conference calls

An intercom call is a call to another handset

that shares the same base station. A conference

call involves a conversation among you, another

handset user and the outside callers.

Make a call to another

handset

Note

If the base station only has 2 registered •

handsets, press int to make a call to another

handset.

1 Press int. The handsets available for

intercom are displayed.

2 Select or enter a handset number, then

press [SELECT] to conrm.

The selected handset rings. »

The intercom is established. »

3 Press END to cancel or end the intercom

call.

Note

If the selected handset is occupied in a call, you •

hear a busy tone.

While you are on the phone

You can go from one handset to another

during a call:

1 Press int.

The current caller is put on hold. »

2 Select or enter a handset number, then

press [SELECT] to conrm.

Wait for the other side to answer your »

call.

English

Summary of content (27 pages)

PAGE 1
5 Intercom and conference calls Toggle between calls An intercom call is a call to another handset that shares the same base station. A conference call involves a conversation among you, another handset user and the outside callers. Transfer a call Make a call to another handset 1 2 3 English Press int to switch between the outside call and the intercom call. Press int during a call. Select or enter the handset number, then press [SELECT] to confirm. Press END when the other side answers your call.
PAGE 2
Note •• Press to join an ongoing conference with another handset if [ADVANCED SET] > [CONFERENCE] is set to [ON]. flash TALK During the conference call 1 2 3 Press int to put the external call on hold and go back to the internal call. »» The external call is put on hold. Press int to toggle between the external and internal call. Press and hold int to establish the conference call again. Note •• If a handset hangs up during the conference call, the other handset remains connected to the external call.
PAGE 3
You can enter text and numbers for handset name, phonebook records, and other menu items. Enter text and numbers 1 2 Press once or several times on the alphanumeric key to enter the selected character. Press [CLEAR] to delete the character. Press call ID / Ph.Book move the cursor left and right. Key Characters (Upper case) 0 .0,/:;“‘!¡?¿*+-%\^ ~| [Sp] 1 @ _ # = < > ( ) & € £ $ ¥ [ ] { } ¤ § ...
PAGE 4
7 Call log The call log stores the call history of all outgoing, missed or received calls. The incoming call history includes the name and number of the caller, call time and date. This feature is available if you have registered to the caller ID service with your service provider. Your phone can store up to 50 call records. The call log icon on the handset flashes to remind you of any unanswered calls. If the caller allows the display of his identity, you can view his name or number.
PAGE 5
Access the phonebook during a call This phone has a phonebook that stores up to 200 records. You can access the phonebook from the handset. Each record can have a name up to 14 characters long and a number up to 24 digits long. Note •• You can view the phonebook on one handset only each time. Press Ph.Book 2 3 View the phonebook 1 2 1 . Select a contact and view the available information. Select the contact, then press [SELECT] to confirm. »» The number can be viewed.
PAGE 6
Note •• The phonebook only saves new number. Tip 4 5 6 •• Press and hold to insert a pause. »» Your new record is saved. Set the melody You can personalize the melody played when someone in the phonebook calls you. Edit the name, then press [OK] to confirm. Press [CLEAR] to delete a character. Edit the number, then press [SAVE] to confirm. »» The record is saved. Delete a record 1 2 3 Press menu. Select [PHONEBOOK] > [DELETE], then press [SELECT] to confirm.
PAGE 7
The redial list stores the call history of dialed calls. It includes the names and/or numbers you have called. This phone can store up to 10 redial records. View the redial records 1 2 Press redial to enter the list of dialed calls. Select a record, press [SELECT]. Delete a redial record 1 2 3 1 2 3 1 2 4 Select the record you want to call. Press . »» The number is dialed out. flash TALK Press redial to enter the list of dialed calls. Select a record, then Press [SELECT] then [OPTION].
PAGE 8
10 Self-defined settings Personalize the sounds Set the handset’s ringtone You can select from 20 ringtones. Customize the settings to make it your own phone. 1 2 Personalize the phone display 3 Name the handset The name of the handset can be up to 14 characters. It is displayed on the handset screen in standby mode. 1 2 3 4 Press menu. Select [PERSONAL SET] > [HANDSET NAME], then press [SELECT] to confirm. Enter or edit the name. To erase a character, press [CLEAR]. Press [OK] to confirm.
PAGE 9
Enhance the audio quality 1 2 3 English XHD (Extreme High Definition) sound mode is an exclusive feature which transmits high fidelity signals to the handset. It makes the phone conversations sound like real-life conversations. When you are in standby mode, Press menu. Select [ADVANCED SET] > [XHD SOUND], then press [ON]/[OFF] to confirm. Select the new setting, then press [SELECT] to confirm. »» The setting is saved. When you are in a call, 1 2 3 Press [OPTION] to enter the options menu.
PAGE 10
11 Call features The phone supports a number of call-related features that help you handle and manage the calls. Auto hang up To end a call, simply place the headset on the base station or charge cradle. Activate/Deactivate auto hang up 1 2 3 Press menu. Select [PERSONAL SET] > [AUTO HANG-UP], then press [SELECT] to confirm. Dial mode Note •• This feature only applies to models that support both tone and pulse dial. Dial mode is the telephone signal used in your country.
PAGE 11
Select an option, then press [SELECT] to confirm. »» The setting is saved. Carrier code Note •• This feature only applies to models with carrier code support. Some service providers require a carrier code to be added when you make a call outside the local area. This feature can decide automatically if a carrier code is needed when you return a call from the incoming call log. Tip •• The carrier code contains 2 or 3 digits. For more information, contact the service provider.
PAGE 12
2 3 Select [ADVANCED SET] > [NETWORK TYPE], then press [SELECT]. This feature checks and formats your outgoing call number before it is dialed out. The prefix number can replace the detect number you set in the menu. For example, you set 604 as the detect number and 1250 as the prefix. When you have dialed out a number such as 6043338888, your phone changes the number to 12503338888 when it dials out. Note •• The maximum length of a detect number is 5 digits.
PAGE 13
3 Select [ADVANCED SET] > [ECO], then press [SELECT] to confirm. English 2 Select the new setting, then press [SELECT] to confirm. »» The setting is saved. »» [ECO] is displayed instead of in standby mode Note •• When the [ECO] mode is activated, the connection range between the handset and the base station can be reduced. Light ring When this feature is activated, the light ring on the base station flashes when there is an incoming call. 1 2 3 Press menu.
PAGE 14
12 Extra features Your phone offers you extra features which keep you organized and informed while on the move. Set the alarm melody 1 2 3 Alarm clock Press menu. Select [CLOCK & ALARM] > [ALARM TONE], then press [SELECT] to confirm. Select a new melody, then press [SELECT] to confirm. »» The setting is saved. Note Your phone has a built-in alarm clock. Check the information below to set your alarm clock. •• The alarm volume is set to the same level as the ringer volume.
PAGE 15
Lock the keypad Press and hold in standby mode. »» The keypad is locked. English 1 format Note •• When the keypad is locked, no call can be made. You can still answer the incoming calls. The keypad is unlocked during the call but is locked automatically after you finish the call. Unlock the keypad 1 Press and hold . »» The keypad is unlocked. format Locate the handset 1 2 3 Press handset locator on the base station. »» All handsets connected to this base station ring.
PAGE 16
13 Advanced settings Register the handsets You can register additional handsets to the base station. The base station can register up to 5 handsets. Manual registration Tip •• The handset number displays beside the handset name in standby mode. Restore default settings You can reset your phone settings to the original factory settings. 1 2 Register your handset manually to the base station. 1 2 3 Press menu on the handset. Select [ADVANCED SET] > [REGISTER], then press [SELECT] to confirm.
PAGE 17
Your phone includes a telephone answering machine that records unanswered calls when it is on. By default, the answering machine is set to the [ANSWER & REC.] mode. You can also access the answering machine remotely and change the settings through the answering machine menu on the handset. The key on the base station light up when the answer machine is on. Turn on the answering machine You can turn on the answering machine through the base station or the handset.
PAGE 18
»» The setting is saved. Set the answer mode You can set the answering machine and select if the callers can leave messages. Select [ANSWER & REC.] if you allow the callers to leave messages. Select [ANSWER ONLY] if you forbid the callers to leave messages. 1 2 3 3 4 5 6 Press menu. Select [ANSWER MACHINE] > [ANSWER MODE], then press [SELECT] to confirm. Select an answer mode, then press [SELECT] to confirm. »» The setting is saved.
PAGE 19
•• No pre-recorded outgoing message can be deleted. Incoming messages (ICM) Each message can be up to 3 minutes long. When you receive new messages, the new message indicator flashes on the answering machine and the handset displays a notification message. Note •• If you pick up the phone when the caller leaves a message, the recording stops and you can talk to the caller directly. Note •• If the memory is full, the answering machine switches to [ANSWER ONLY] automatically.
PAGE 20
2 3 Select [ANSWER MACHINE] > [DELETE ALL], then press [SELECT] to confirm. »» The handset displays a confirmation request. •• You can delete the read messages only. No deleted messages can be recovered. Call screening You can hear the caller while he is leaving a message. Then you can decide whether or not to talk to the caller directly. From the base Press / to adjust the speaker volume during call screening. The lowest volume level turns off the call screening.
PAGE 21
•• You have 2 chances to enter the correct PIN code before your phone hangs up. 4 Press a key to carry out a function. See the Remote access commands table below for a list of available functions. Note Behavior of the light ring and LED keys on the base station The light ring is on when you approach the base station, or when there is a new call or new/unread message. The table below shows you the current status with different light ring flashing and LED keys behavior on the base station.
PAGE 22
15 Default settings Answering machine default settings Language Handset name Date Date format Time Time format Auto clock Clock in standy mode Alarm Phonebook list Auto hang up Recall time Area code Carrier code Network type Answering Machine Ans machine status Ans machine mode Base call screening Outgoing message memory Incoming message memory Remote access PIN code Voice language Country dependent PHILIPS 01/01/09 DD/MM 00:00 24-hour On Digital Off Unchanged On Country dependent [Empty] [Empty] PSTN
PAGE 23
English 16 Technical data Display • Progressive LCD backlight General telephone features • Dual mode caller name & number identification • 15 polyphonic ringer melodies and 5 standard ringer melodies • Conference call and voicemails • Intercom Phonebook list, Redial list and Call log • Phonebook list with 200 entries • Redial list with 10 entries • Call log with 50 entries Battery • 2 x AAA Ni-MH 1.2V Rechargeable 650mAh batteries Adaptor • Base: Input 120V 60Hz 0.1A, Output: 6V 0-0.
PAGE 24
17 Frequently asked questions The signal icon flashes. •• The handset is out of range. Move it closer to the base station. If the handset displays [UNREGISTERED], register the handset. Tip •• For more information, see “Register the handsets” on the Advanced settings section. IF I fail to register the additional handsets to the base station, what do I do? Your base memory is full. Unregister the unused handsets and try again. No dialing tone •• Check your phone connections. •• The handset is out of range.
PAGE 25
43
PAGE 26
44
PAGE 27
45