SCD520
11 2 12 2 22 1 21 10 5 3 4 9 8 6 7 20 18 19 13 14 15 16 17 12 13 1 2 3 4 8 5 6 7 17 14 9 10 11 15 16 1 2 3 4 5
SCD520 English 6
English IMPORTANT SAFETY INSTRUCTIONS Some of the following information may not apply to your particular product; however, when using baby monitor equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth.
English 19 Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 20 Never push objects of any kind into this product through casing slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 21 To reduce the risk of electric shock, do not disassemble this product, but call 1-800-54-AVENT (1-800-542-8368) for assistance.
English 12 There is a risk of explosion if batteries are replaced with an incorrect type. For the parent unit, always use the SCD520 NiMH rechargeable battery pack as supplied with the appliance. SAVE THESE INSTRUCTIONS CAUTION:THE SYMBOL SHOWN IN FIGURE 1 MEANS THAT THERE IS A RISK OF EXPLOSION OF THE BATTERIES AND/OR OF SERIOUS DAMAGE TO THE BABY MONITOR IF THE BATTERIES OR THE ADAPTER ARE REPLACED WITH AN INCORRECT TYPE. Adapters for baby unit and charger: - Input: 120 VAC 60 Hz - Output: 7.
English - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
English 15 Socket for small appliance plug 16 Charger 17 Charging light 18 Compartment for rechargeable battery pack 19 Neck strap 20 Lid of compartment for rechargeable battery pack 21 Rechargeable battery pack (included) 22 Opening for neck strap B Baby unit 1 On/off button 3 2 PAGE button 3 Play/stop button E 4 Lullaby button K 5 Battery light T 6 Nightlight button Q 7 Power-on light 8 Volume +/– buttons 9 Microphone 10 Adapter 11 Large appliance plug 12 Loudspeaker 13 Temperature sensor 14 Sock
English , , , , , , , , , , , , 11 Make sure the baby unit and power cord are always out of reach of the baby (at least 3 feet / 1 meter away). Never place the baby unit inside the baby’s bed or playpen. Never cover the baby monitor with a towel or blanket. Never immerse any part of the baby monitor in water or any other liquid. Never use the baby monitor in moist places or close to water.
English 2 Insert four non-rechargeable batteries. Note: Make sure the + and - poles point in the right direction. 3 Reattach the lid. Note:When the batteries are low, the battery light on the baby unit flashes red. Parent unit Battery operation (rechargeable battery pack) The parent unit comes with a SCD520 NiMH rechargeable battery pack.
English 13 4 Insert the small appliance plug into the charger, put the adapter in a wall socket and place the parent unit in the charger. , The charging light on the charger goes on. , The display shows a charging battery symbol to indicate that the parent unit is charging. 5 Leave the parent unit in the charger until the battery pack is fully charged. , During charging, the charging light on the charger lights up continuously.
English , The battery light T lights up briefly and then goes out again. 3 Press and hold the on/off button 3 on the parent unit until the sound level lights light up briefly. , The display goes on and the battery symbol appears on the display. , The LINK light flashes red and the message ‘Searching’ appears on the display. , The LINK light on the parent unit turns green and lights up continuously when a connection has been established between the baby unit and parent unit.
English 15 , After 2 seconds the message ‘Linked’ disappears and the temperature value is shown on the display. , If no connection is established, the LINK light on the parent unit stops flashing and lights up red. The parent unit beeps from time to time and the message ‘Not Linked’ appears on the display. Positioning the baby monitor 1 Place the baby unit at least 3 feet/1 meter away from your baby. 2 Place the parent unit within the operating range of the baby unit.
English For wet and moist materials, the range loss may be up to 100%. Features The following features are described in chapter ‘Menu options’, as they can only be operated in the menu of the parent unit: - Adjusting microphone sensitivity - Sound alert on/off - Setting room temperature range (minimum and maximum temperature) - Temperature alert on/off Adjusting loudspeaker volume 1 Press the volume + or – button on the baby unit until the desired loudspeaker volume for the baby unit has been reached.
English - 17 When the baby unit picks up a sound, one or more sound level lights on the parent unit go on. The number of lights that go on is related to the loudness of the sound picked up by the baby unit. Nightlight 1 Press the nightlight button Q on the baby unit to switch on the nightlight. , Q appears on the display of the parent unit. 2 Press the nightlight button Q again to switch off the nightlight. , The nightlight dims gradually before it goes out completely.
English 3 - To select another lullaby when a lullaby is playing: Press the lullaby button K on the baby unit. Wait 2 seconds for the next lullaby to start. If you want another lullaby, press the lullaby button K on the baby unit again. Out of range alert When the parent unit is out of range of the baby unit, the parent unit beeps from time to time and the message ‘Not linked’ appears on the display. The LINK light on the parent unit flashes red.
English 19 Adjusting microphone sensitivity You can set the microphone sensitivity of the baby unit to the desired level. You can only change the microphone sensitivity when a connection between the baby unit and the parent unit has been established, i.e. when the LINK light on the parent unit lights up green continuously. 1 Select ‘Sensitivity’ with the + and - buttons. 2 Press the OK button to confirm. 3 Select the desired microphone sensitivity level for the baby unit with the + and - buttons.
English 3 Select ‘Range’ with the + and - buttons. 4 Press the OK button to confirm. 5 Set the desired minimum temperature with the + and - buttons. 6 Press the OK button to confirm. 7 Set the desired maximum temperature with the + and - buttons. 8 Press the OK button to confirm. , The message ‘Saved’ appears on the display. Note: If the temperature in the baby’s room drops below or exceeds the set temperature range, the display of the parent unit is on continuously.
English 21 - Temperature alert: off - ‘Temperature low’ alert: 57°F - ‘Temperature high’ alert: 86°F Baby unit - Loudspeaker volume: 3 - Nightlight: off - Lullaby: 1 Accessories Belt clip and neck strap If the battery pack of the parent unit is sufficiently charged, you can take the unit with you inside and outside the house if you attach the unit to your belt or waistband with the belt clip or if you hang it around your neck with the neck strap.
English This appliance has no other user-serviceable parts. For assistance call 1800-54-AVENT (1-800-542-8368). Storage - - When you are not going to use the baby monitor for some time, remove the non-rechargeable batteries from the baby unit and the rechargeable battery pack from the parent unit. Store the parent unit, the baby unit, the charger of the parent unit and the adapters in a cool and dry place. Do not wrap cord around the monitor when storing.
English 23 Warranty FULL TWO YEAR WARRANTY Philips Electronics North America Corporation (USA) and Philips Electronics Ltd (CANADA) warrant each new Philips AVENT product, model SCD520/00, against defects in materials or workmanship for a period of two years from the date of purchase, and agrees to repair or replace any defective product without charge.
English Question Answer Why does the parent unit beep? If the parent unit beeps while the LINK light lights up red continuously and the message ‘Not Linked’ is shown on the display, the connection with the baby unit is lost. Move the parent unit closer to the baby unit. If the parent unit beeps and the battery symbol on the display is empty, the rechargeable battery pack of the parent unit is running low. Recharge the battery pack.
English Question 25 Answer You may have set a maximum room temperature that is lower than the actual room temperature or a minimum room temperature that is higher than the actual room temperature. The baby unit continues to send data to the parent unit and therefore uses more power.This causes the nonrechargeable batteries of the baby unit to run low quickly. Perhaps you have switched on the nightlight. If you want to use the nightlight, we advise you to run the baby unit on electrical power.
Manufactured for: Philips Consumer Lifestyle, a division of Philips Electronics North America Corporation. 1600 Summer Street, 5 Fl., Stamford, CT 06905-5125 0682 /AVENT 4222.002.7190.