SCD510
2
SCD510 English 6
English IMPORTANT SAFETY INSTRUCTIONS Some of the following information may not apply to your particular product; however, when using baby monitor equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth.
English 20 Never push objects of any kind into this product through casing slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 21 To reduce the risk of electric shock, do not disassemble this product, but call 1-800-54-AVENT (1-800-542-8368) for assistance. Opening or removing covers (except battery compartment lids) may expose you to dangerous voltage or other risks.
English SAVE THESE INSTRUCTIONS CAUTION:THE SYMBOL SHOWN IN FIGURE 1 MEANS THAT THERE IS A RISK OF EXPLOSION OF THE BATTERIES AND/OR OF SERIOUS DAMAGE TO THE BABY MONITOR IF THE BATTERIES OR THE ADAPTER ARE REPLACED WITH AN INCORRECT TYPE. Adapter for baby unit: - Input: 120 VAC 60 Hz - Output: 7.5 VDC 400 mA - Adapter no. UD075040B Adapter for parent unit: - Input: 120 VAC 60 Hz - Output: 4.5 VDC 400 mA - Adapter no.
English - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
English B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Baby unit On/off button 3 PAGE button Nightlight button Q Volume +/– buttons Power-on light Battery light T Microphone Loudspeaker Adapter Large appliance plug Socket for large appliance plug Non-rechargeable batteries (not included) Compartment for non-rechargeable batteries Lid of compartment for non-rechargeable batteries Important , , , , , , , , , , , , , , , , , , Read the user manual carefully before you use the appliance and save it for futu
English 11 Preparing for use Baby unit You can use the baby unit corded or on non-rechargeable batteries. Even if you are going to use the unit corded, we advise you to insert the nonrechargeable batteries. This guarantees automatic back-up in case of power failure. Cord operation 1 Put the large appliance plug in the baby unit and put the adapter in a wall socket. , The power-on light goes on. Battery operation (non-rechargeable batteries) The baby unit runs on four 1.5V R6 AA batteries (not included).
English 1 Remove the lid of the compartment for the rechargeable battery pack. 2 Insert the rechargeable battery pack. Note: Make sure the + and - poles of the battery pack point in the right direction. 3 Reattach the lid. 4 Put the small appliance plug in the parent unit and put the adapter in a wall socket. 5 Leave the parent unit plugged in until the battery pack is fully charged. , During charging, the battery light lights up red continuously.
English 13 Using the appliance 1 Place the parent unit and the baby unit in the same room to test the connection. Make sure the baby unit is at least 3 feet/1 meter away from the parent unit. 2 Press and hold the on/off button 3 on the baby unit until the green power-on light goes on. Note:The power-on light always lights up green, even when there is no connection with the parent unit. , The nightlight lights up briefly and then goes out again.
English , The LINK light on the parent unit turns green and lights up continuously when a connection has been established between the baby unit and parent unit. , If no connection is established, the LINK light on the parent unit stops flashing and lights up red. The parent unit beeps from time to time. Positioning the baby monitor 1 Place the baby unit at least 3 feet/1 meter away from your baby. 2 Place the parent unit within the operating range of the baby unit.
English Dry materials Material thickness Loss of range Metal or aluminum sheets < 1cm/0.4in 100% 15 For wet and moist materials, the range loss may be up to 100%. Features Adjusting loudspeaker volume 1 Press the volume + or - button on the baby unit until the desired loudspeaker volume for the baby unit has been reached. Note:You only have to adjust the baby unit volume when you use the talk function (see below).
English Nightlight 1 Press the nightlight button Q on the baby unit to switch on the nightlight. 2 Press the nightlight button Q again to switch off the nightlight. , The nightlight dims gradually before it goes out completely. Tip: Switch off the nightlight when you operate the baby unit on the nonrechargeable batteries.This saves power.
English 17 Reset function This function allows you to reset the parent unit and the baby unit to the default settings. You can use this function if problems occur that you cannot solve by following the suggestions in chapter ‘Frequently asked questions’. You have to reset each unit separately. 1 Press the on/off button to switch off the parent unit. Remove the small plug from the parent unit and the adapter from the wall socket. 2 Press and hold the volume down (-) button.
English 3 Clean the adapters with a dry cloth. This appliance has no other user-serviceable parts. For assistance call 1800-54-AVENT (1-800-542-8368). Storage - - When you are not going to use the baby monitor for some time, remove the non-rechargeable batteries from the baby unit and the rechargeable battery pack from the parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place. Do not wrap cord around the monitor when storing.
English 19 Environment - Dispose of batteries properly. Do not incinerate. Batteries may explode if overheated. Do not wrap in metal or aluminum foil. Wrap in newspaper before discarding. It is suggested that you contact your local town or city to determine proper battery redemption site(s) in your area.
English Question Answer Why does the LINK light on the parent unit flash red? The baby unit and the parent unit are out of range of each other. Move the parent unit closer to the baby unit. Why does the battery light on the baby unit flash red? The non-rechargeable batteries of the baby unit are running low. Replace the non-rechargeable batteries or connect the baby unit to an electrical outlet (see chapter ‘Preparing for use’).
English 21 Question Answer Why does the charging time of the parent unit exceed 8 hours? The parent unit may be switched on during charging. Switch off the parent unit during charging. The specified operating range of the baby monitor is 330 meters/1000 feet. Why does my baby monitor manage a much smaller distance than that? The specified range is only valid outdoors in open air. Inside your house, the operating range is limited by the number and type of walls and/or ceilings in between.
In US manufactured for Philips Consumer Lifestyle, a division of Philips Electronics North America Corporation. 1600 Summer Street, 5 Fl., Stamford, CT 06905-5125 In Canada imported for Philips Electronics Ltd, 281 Hillmount Road, Markham, ON L6C2S3 Call TOLL-FREE 1.800.54.AVENT En EE.UU. fabricado para Philips Consumer Lifestyle, una división de Philips Electronics North America Corporation. 1600 Summer Street, 5 Fl.