Always here to help you Register your product and get support at www.philips.
a e b f c g h d i 1
1 Introduction 1 Introduction 3 2 General description 3 3 3.1 3.2 Preparing for use Baby unit Parent unit 4 4 5 4 4.1 Using the appliance Positioning the baby monitor 6 7 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.
II Baby unit 1 2 3 4 5 6 7 8 9 10 11 12 13 Antenna Power-on light Microphone Lens Loudspeaker Base Nightlight and nightlight button Wall-mounting holes Battery compartment lid Socket for appliance plug On/off switch Appliance plug Adapter 3 Preparing for use IMPORTANT: Read the important safety instructions carefully before you use the video baby monitor and keep them for future reference. 3.1.2 Placing the non-rechargeable batteries In case of a power failure, the baby unit can run on four 1.
Reattach the lid. 3.2 Parent unit 1 2 3.2.1 Operation on rechargeable battery Slide down the battery compartment lid to remove it. E nglish 3 Insert the rechargeable battery. B Warning: Unplug the parent unit and make sure your hands and the unit are dry when you insert the rechargeable battery. •• The parent unit comes with a rechargeable Li-ion polymer 1100mAh battery. •• Charge the parent unit before you use it for the first time or when the parent unit indicates that the battery is low.
4 Insert the appliance plug into the parent unit and insert the adapter into an electrical outlet. D Note: •• When the parent unit is charged for the first time, the operating time is less than 7 hours. The rechargeable battery only reaches its full capacity after four discharging and charging cycles. •• The battery gradually discharges, even when the parent unit is turned off. 4 Using the appliance 1 Place the parent unit and the baby unit in the same room to test the connection. m/ >1.
3 E Tip: Find out what the best position is for the parent unit by looking at the signal strength symbol. The number of stripes indicates the quality of the connection. Press and hold the on/off button on the parent unit. E nglish D Note: The power-on light always lights up green, even when there is no connection with the parent unit. •• If no connection can be established, the parent unit beeps and the out-of-range image appears on the display. 1.
2 There are two ways to position the baby unit: 1 Place the baby unit on a stable, level and horizontal surface. 2 Mount the baby unit to the wall as shown in the figure with the screws supplied. 4 Place the parent unit within the operating range of the baby unit. Make sure it is at least 1.5 meters (5 feet) away from the baby unit to avoid acoustic feedback. m/ >1.5 E Tip: •• Use the provided template, to mark the exact location of the screw holes on the wall.
5.1 Adjusting loudspeaker volume You can adjust the loudspeaker volume of the parent unit to the level you prefer. 1 5.2 Adjusting display brightness You can adjust the display brightness of the parent unit to the level you prefer. 1 Press the brightness adjustment buttons on the parent unit to adjust the brightness of the video display. Press the volume up or down button to adjust the volume. •• The display brightness bar appears on the display to show the selected display brightness.
5.3 Sound level lights •• The voice activation light on the parent unit goes on and the voice activation image appears on the video display. The parent unit continuously monitors the sound level in your baby’s room and the sound level lights let you know if there is any activity. If your baby cries, the blue sound level lights light up on the parent unit. •• As long as no sound is detected, the sound level lights are out.
2 2 To select another lullaby, press the lullaby button. Continue pressing the ‘next lullaby’ button until you hear the lullaby you prefer. E nglish •• The nightlight on the base of the baby unit goes on. Press the nightlight button again to turn off the nightlight. 5.6 Lullaby function 1 Press the lullaby play/stop button on the parent unit to play a lullaby. D Note: You can also select the repeat symbol to play all lullabies repeatedly in a loop.
5.7 Out-of-range alert When the parent unit is out of range of the baby unit, the parent unit beeps every 20 seconds and the out-of-range image appears on the video display. D Note: The out-of-range alert is also active when the baby unit is turned off. 5.8 Night vision The camera has infrared lights that allow you to see your baby clearly, even in a dark room. When the camera detects low light levels, the infrared lights are turned on automatically. Place the baby unit 1 to 1.5 meters (3.
B Warning: Do not immerse the parent unit and the baby unit in water and do not clean them under running water. B Warning: Do not use a cleaning spray or liquid cleaners. 1 Turn off the baby unit and the parent unit and remove the adapters from the electrical outlet. 2 Clean the parent unit and the baby unit with a dry cloth. D Note: Fingerprints or dirt on the lens of the baby unit may affect the camera’s performance. Avoid touching the lens with your fingers.
11 Frequently asked questions This chapter lists the questions most frequently asked about the appliance. If you cannot find the answer to your question, visit www.philips.com/ support for more frequently asked questions or contact the Consumer Care Center in your country.
Why does the charging time of the parent unit exceed 2.5 hours? •• The parent unit may be turned on during charging. Turn off the parent unit during charging. Why do I need to keep the baby unit and its cord at least 1 meter (3.5 feet) from my baby? •• To avoid strangulation with the cord and for optimal sound detection, always place the baby unit and its cord at least 1 meter (3.5 feet) away from the baby.
•• Perhaps the baby monitor is in auto mute. When the baby unit detects a low sound level, e.g. the sleeping sound of the baby, the parent unit automatically mutes the sound output so that you do not hear this sound. When the baby starts to cry, the parent unit automatically turns on the volume again to let you hear the crying sound. •• The baby unit may be too far away from your baby. Make sure the baby unit is not further than 1.5 meters (5 feet) from your baby, but not closer than 1 meter (3.
E nglish Output video display Why does the video display flicker? •• Interference may occur when the parent unit is out of range of the baby unit. Interference may also occur if there are too many walls or ceilings between the parent unit and the baby unit or when other 2.4GHz wireless devices are turned on (e.g. microwave, Wi-Fi router). Put the parent unit in a different place, closer to the baby unit, or turn off other wireless devices.
4222.005.0395.
Always here to help you Register your product and get support at www.philips.
2 ENGLISH Know these safety symbols CAUTION - This “bolt of lightning” indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. - The exclamation mark calls attention to features that require you to read the enclosed user information closely to prevent operating and maintenance problems.
ENGLISH 3 5HIHU DOO VHUYLFLQJ WR TXDOLÀHG VHUYLFH SHUVRQQHO 6HUYLFLQJ LV UHTXLUHG when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Please check the power cord periodically to prevent potential damages, such as worn or cut cord. For assistance, visit our website www.philips.
4 ENGLISH - For the adapters and battery types, please refer to chapter ‘Replacement’ for details. To prevent battery explosion or leakage, which can damage the baby monitor and cause burns and skin or eye irritation: do not recharge non-rechargeable batteries LQVHUW EDWWHULHV LQ WKH ULJKW GLUHFWLRQ remove batteries if you are not going to use the product for more than 30 days NHHS WKH EDWWHU\ DZD\ IURP H[FHVVLYH KHDW VXFK DV VXQVKLQH ÀUH RU WKH OLNH do not leave empty batteries in the baby unit.
ENGLISH 5 Storage precautions - 8VH DQG VWRUH WKH EDE\ PRQLWRU EHWZHHQ & ) DQG & ) Do not expose the baby unit and parent unit to extreme cold or heat or to direct sunlight. Do not put the baby unit and the parent unit close to a heating source. Replacement If you need to replace the battery and the adapter, please refer to the user manual and contact the Philips Customer Care Center. Supplied AC/DC Adapter for parent unit.
6 ENGLISH interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
0979 4222.005.0445.