User's Manual

ManualsBrandsPhilips Electronics Industries ManualsComputers & AccessoriesLCD Color Monitor

Product Information

Product Features • Technical Specifications • Resolution & Preset Modes •

Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification •

Pin Assignment • Product Views • Physical Function

Product Features

170B4MG

17-inch color LCD monitor with excellent display performance

Dual input - accepts DVI-D digital and VGA analog inputs

Embedded AC power supply

Front firing speakers with 2x2W RMS stereo sound output

Advanced AUTO adjustment optimizes picture quality

Rotation for both portrait and landscape display

Liner height adjustment for best viewing position

Adjustable tilt and swivel function

Optional self-powered USB hub

RETURN TO TOP OF THE PAGE

Technical Specifications*

LCD PANEL

• Type TFT LCD

• Screen size 17" / 43.2cm diagonal

• Pixel Pitch 0.264 x 0.264mm

• LCD Panel type

1280 x 1024 pixels

R.G.B. vertical stripe

Anti-glare polarizer, hard coated

• Effective viewing area 337.9 x 270.3 mm

• Display Colors 16M colors

SCANNING

Vertical refresh rate 56Hz-76Hz

Horizontal Frequency 30kHz-82kHz

VIDEO

• Video dot rate 135MHz

• Input impedance

- Video

75 ohm

Installstion and Operating Instructions

Exhibit 3

Summary of content (21 pages)

PAGE 1
Exhibit 3 Installstion and Operating Instructions Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Physical Function Product Features 170B4MG z z z z z z z z z 17-inch color LCD monitor with excellent display performance Dual input - accepts DVI-D digital and VGA analog inputs Embedded AC power supply Front firing speakers with 2x2W RMS stereo sound
PAGE 2
- Sync 2.2K ohm • Input signal levels 0.7 Vpp • Sync input signal Separate sync Composite sync Sync on green • Sync polarities Positive and negative • Video interface Dual input: D-Sub (analog) and DVI-D (digital) are available and user selectable AUDIO • Input signal level 0.7 Vpp • Headphone out signal level 32 ohm 20+20mW • Input signal connector 3.
PAGE 3
3 user definable modes 15 factory preset modes: H. freq (kHz) Resolution V. freq (Hz) 31.5 640*350 70 31.5 720*400 70 31.5 640*480 60 35.0 640*480 67 37.5 640*480 75 35.2 800*600 56 37.9 800*600 60 46.9 800*600 75 49.7 832*624 75 48.4 1024*768 60 60.0 1024*768 75 69.0 1152*870 75 71.8 1152*900 76 63.
PAGE 4
efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimension (WxHxD) 375 x 413 x 184 mm (incl. Pedestal) • Weight 6.3 Kg • Tilt / Swivel 0° ~ 35° / + - 175° • Height adjustment rang 50mm • Portrait display 90° rotation counter clockwise • Power supply 100 — 240 VAC, 50/60 Hz • Power consumption 40 W* (typ.
PAGE 5
8 No connect 16 Hot Plug Detect 24 T.M.D.S. Clock- 2. The 15-pin D-sub connector (male) of the signal cable: Pin Assignment No. Pin Assignment No. 1 Red video input 9 +5V 2 Green video input/SOG 10 Logic ground 3 Blue video input 11 Identical output connected to pin 10 4 Sense (GND) 12 Serial data line (SDA) 5 Not connected 13 H. Sync / H+V 6 Red video ground 14 V.
PAGE 6
RETURN TO TOP OF THE PAGE Physical Function 1) Tilt 2) Swivel 3) Height adjustment 4) Portrait display Turn monitor from landscape view to portrait view 4.
PAGE 7
4.2) Rotate the monitor body 90 degrees counter clockwise.
PAGE 8
Installing your LCD Monitor Your LCD Monitor : Front View Product Description • Connecting to Your PC • Remove and re-install the base • Getting Started • Optimizing Performance • Accessories (optional) Front View Product Description UP and DOWN buttons are used when adjusting the OSD of your monitor LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. Signal inputs selective hotkeys.
PAGE 9
1. Audio power on/off and volulme adjustment 2. Audio power LED 3. BASS on/off 4. Built-in Mic 5. Mute on/off RETURN TO TOP OF THE PAGE Side View 1. Headphone Jack 2.
PAGE 10
RETURN TO TOP OF THE PAGE Rear View 1. Audio in 2. Mic out 3. DC 12V in 1.
PAGE 11
2. AC power in 3. DVI-D Connector 4. D-SUB Connector RETURN TO TOP OF THE PAGE Optimizing Performance z For best performance, ensure that your display settings are set at 1024x768@60Hz (for 14"/15") or 1280x1024, 60Hz (for 17"/18"). Note: You can check the current display settings by pressing the 'OK' button once. Go into the Product Information. The current display mode is shown on the item called RESOLUTION.
PAGE 12
Connecting to Your PC Your LCD Monitor : Front View Product Description • Accessory Pack • Connecting to Your PC • Remove and re-install the base • Getting Started • Optimizing Performance • Accessories (optional) Accessory Pack Unpack all the parts.
PAGE 13
1) Thread power cable through the hole at the bottom of the base, and plug onto monitor firmly. 2) Connect microphone and audio cables onto the rear side of base if any 3) Double check all cables' connection closely. Make sure they are all connected well.
PAGE 14
(a) Turn off your computer and unplug its power cable. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Connect the audio and microphone cables to the audio and mic connectors on the back of your computer. (d) Plug the power cord of your computer and your monitor into a nearby outlet. (e) Turn on your computer and monitor. If the monitor displays an image, installation is complete.
PAGE 15
Remove and Re-install the Base Your LCD Monitor : Front View Product Description • Accessory Pack • Connecting to Your PC • Getting Started • Optimizing Performance • Accessories (optional) Remove and Re-install the Base : Remove the base • Re-install the base Condition: z z for VESA standard mounting applications for optional base replacement Remove the Base 1) (a) Tilt monitor on certain angle. (b) Pull cables out of the hole at the bottom of base.
PAGE 16
3) Unscrew the four screws of the base RETURN TO TOP OF THE PAGE Re-install the Base 1) Put monitor face down on the safe surface and plug in the cables into connectors. 2) Mount the base onto the monitor body and fix four screws securely.
PAGE 17
hole at the bottom of the base. 4) For Multimedia base, plug the flying DC power cable of base onto monitor.
PAGE 18
Regulatory Information TCO '95 Information • TCO '95 Environmental Requirements • TCO '99 Information • TCO '99 Environmental Requirements • CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
PAGE 19
- EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment) - EN55024:1998 (Immunity requirement of Information Technology Equipment) - EN61000-3-2:1995 (Limits for Harmonic Current Emission) - EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable - 73/23/EEC (Low Voltage Directive) - 89/336/EEC (EMC Directive) - 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 lev
PAGE 20
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 21
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement. N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques. CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.