CCZ134comb 4/5/99 9:30 PM Page 1 Color TV with built-in VCR CCZ134AT Owner’s Manual Important! Return your Warranty Registration Card within 10 days. See why inside.
CCZ134comb 4/5/99 9:30 PM Page 2 Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. Once your PHILIPS MAGNAVOX purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
CCZ134comb 4/5/99 9:30 PM Page 3 Introduction 3 Welcome to your TV/VCR owner’s manual. This manual has six sections: Setting Up Your TV/VCR; Description of Controls; Basic Operations; Recording Options; Playing Options; and Information You May Need. The instructions explain all of the TV/VCR’s features, which are listed below.
CCZ134comb 4/5/99 9:30 PM Page 4 4 Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hooking Up the TV/VCR . . . . . . . . . . . . . . . . .
CCZ134comb 4/5/99 9:30 PM Page 5 Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 1 2 2 3 3 Remove the battery compartment lid on the bottom of the remote control by pressing in the tab and lifting the lid. Place three AA batteries inside the battery compartment with their + and – ends aligned as indicated. Replace the battery compartment lid. Erasure Prevention 1 Video cassette tapes have record tabs to ensure that recordings are not accidentally erased.
CCZ134comb 4/5/99 9:30 PM Page 6 6 Hooking Up The TV/VCR 1 Hook up your TV/VCR using one of the connections shown. A. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna Connect a Cable signal or an antenna to the ANT(enna) Jack. ANT. ANT. B. Hooking Up Your TV/VCR With a Cable Box To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box. Connect the Cable signal to the IN Jack on the Cable Box.
CCZ134comb 4/5/99 9:30 PM Page 7 Hooking Up The TV/VCR (cont’d) 7 D. Hooking Up Your TV/VCR to Another Video Source (VCR or Camcorder) You may need this connection if you want to copy tapes. Details are on page 34. AUDIO/VIDEO OUT Jacks on VCR 3CH 4CH AUDIO VIDEO OUT IN Use an Audio cable to connect the AUDIO OUT Jack on the VCR to the AUDIO Jack on the front of the TV/VCR. IN ANT. OUT AUDIO VIDEO AUDIO EARPHONE 3CH 4CH AUDIO VIDEO OUT IN VIDEO STOP/EJECT REW PLAY F.
CCZ134comb 4/5/99 9:30 PM Page 8 8 Turning On the TV/VCR Before you turn on the TV/VCR, make sure there are batteries in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button. The TV/VCR will come on and the screen shown below will appear.
CCZ134comb 4/5/99 9:30 PM Page 9 Language Selection 9 Follow the steps below to change the language of the on-screen displays and menus. 1 2-4 Press the COMBI button, then press the MENU button. EJECT POWER > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS SLEEP SPEED MEMORY PAUSE/STILL REC/OTR PLAY 2 REW F.FWD STOP Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button.
CCZ134comb 4/5/99 9:30 PM Page 10 10 Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. 1 Press the COMBI button, then press the MENU button. 5 2-4 Wait for the TV/VCR to set up channels. TO ADJUST PRESS { / B EJECT POWER > INPUT CABLE EXIT PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION SLEEP SPEED MEMORY PAUSE/STILL REC/OTR PLAY REW 2 F.
CCZ134comb 4/5/99 9:30 PM Page 11 Automatic Channel Setup (cont’d) 11 Adding/Deleting Channels 1 Press the COMBI button, then press the MENU button. EJECT POWER SLEEP TO ADJUST PRESS { / B CH123 SAVED > CHANNEL INPUT EXIT PRIM. SETUP VCR PROGRAM VCR SETUP 4 2 Press the PLAY/▲ button or the STOP/▼ button to select CHANNEL. TO ADJUST PRESS { / B CH123 SAVED > CHANNEL INPUT EXIT PRIM. SETUP VCR PROGRAM VCR SETUP SPEED MEMORY PAUSE/STILL REC/OTR PLAY REW F.
CCZ134comb 4/5/99 9:30 PM Page 12 12 Setting the Clock There are three ways to set the clock: Manually, with Automatic PBS Channel Selection, or with Manual PBS Channel Selection. With manual clock setting, you tell the TV/VCR the current time. With Automatic or Manual PBS Channel Selection, the TV/VCR gets the time from your local PBS station.
CCZ134comb 4/5/99 9:30 PM Page 13 Setting the Clock (cont’d) 13 4 If ON appears beside AUTO CLOCK, press the F.FWD/B button so that OFF appears to the right of AUTO CLOCK, then press the MENU button. If OFF appears beside AUTO CLOCK, press the MENU button. SET MANUAL CLOCK 5-6 EJECT POWER TIME – – : – – SLEEP SPEED MEMORY DATE – – / – – / – – PAUSE/STILL REC/OTR PLAY TO END PRESS EXIT REW 5 MENU Press two Number buttons for the hour(s) and two Number buttons for the minute(s).
CCZ134comb 4/5/99 9:30 PM Page 14 14 Setting the Clock (cont’d) Automatic PBS Channel Selection 1 Press the COMBI button, then press the MENU button. > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 2-3 PRESS B EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR 2 PLAY REW F.FWD STOP Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button. MENU PRIMARY SETUP STATUS/EXIT 1 2 3 4 5 6 7 8 9 A.
CCZ134comb 4/5/99 9:30 PM Page 15 Setting the Clock (cont’d) 15 5 Press the PLAY/▲ button or the STOP/▼ button to select SET PBS CH. AUTO. Then, press the F.FWD/B button. 6 Wait for the TV/VCR to find the time. SET AUTO CLOCK TIME ––:–– DATE ––/––/–– EJECT POWER SLEEP NOW SEARCHING SPEED MEMORY PAUSE/STILL REC/OTR TO END PRESS EXIT PLAY 6 REW F.FWD STOP MENU NOW SEARCHING flashes on the TV/VCR screen.
CCZ134comb 4/5/99 9:30 PM Page 16 16 Setting the Clock (cont’d) Manual PBS Channel Selection 1 Press the COMBI button, then press the MENU button. > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 2-3 PRESS B EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR 2 PLAY REW Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button.
CCZ134comb 4/5/99 9:30 PM Page 17 Setting the Clock (cont’d) 17 5 Press the PLAY/▲ button or the STOP/▼ button to select SET PBS CH. MANUAL. Then, press the F.FWD/B button. 7 Wait for the TV/VCR to find the time. AUTO CLOCK (PBS) CH – – TIME ––:–– DATE ––/––/–– EJECT POWER SLEEP SELECT CHANNEL NUMBER TO END PRESS EXIT SPEED MEMORY PAUSE/STILL REC/OTR PLAY 6 REW F.FWD STOP Use the Number buttons to select your PBS station.
CCZ134comb 4/5/99 9:30 PM Page 18 18 Daylight-Saving Time When the Daylight-Saving Time feature is ON, the TV/VCR clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October. To turn Daylight-Saving Time ON or OFF, follow the steps below. 1 2-4 EJECT POWER Press the COMBI button, then press the MENU button. SLEEP SPEED MEMORY PAUSE/STILL REC/OTR > PRIM.
CCZ134comb 4/5/99 9:30 PM Page 19 Time Zone 19 1 Press the COMBI button, then press the MENU button. > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 2-5 EJECT POWER 2 SLEEP SPEED MEMORY PAUSE/STILL REC/OTR Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button.
CCZ134comb 4/5/99 9:30 PM Page 20 20 Setting the Remote to Operate a Cable Box/DBS Your TV/VCR remote control may operate your Cable Box/DBS. If the remote control doesn’t operate your Cable Box/DBS now, follow the steps below to program your remote control. 1 Turn on your Cable Box/DBS. Point the remote control at your Cable Box/DBS and press the CABLE/DBS button. Then, press the POWER button. If your Cable Box/DBS turns off, try the other Cable Box/DBS buttons (see pages 24 - 25 for details).
CCZ134comb 4/5/99 9:30 PM Page 21 Setting the Remote to Operate a Cable Box/DBS (cont’d) 21 5 Within 30 seconds, press the Number buttons to enter the two-digit code for your Cable Box/DBS. For example, if you have a Zenith Cable Box, press Number buttons 2, 3. 6 EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR PLAY REW 6 Repeat step 1. If the remote control works your Cable Box/DBS, you’re finished.
CCZ134comb 4/5/99 9:30 PM Page 22 22 Front Panel Cassette Compartment Insert a video cassette tape here. Wireless Remote Sensor Receives a signal from your remote control so you can operate the TV/VCR from a distance. STOP/EJECT Button Press once to stop the tape. When playback is stopped, press to eject the tape. Press to select an item in the pop up menu. VIDEO Jack Connect this jack to the video out jack of a camcorder or a VCR. Details are on page 34.
CCZ134comb 4/5/99 9:30 PM Page 23 Rear Panel 23 ANT. AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR. ANT(enna) Jack Connect your antenna or cable here. Details are on pages six - seven. Antenna Hole Connect the stem of an indoor antenna here. Details are on page six.
CCZ134comb 4/5/99 9:30 PM Page 24 24 Remote Control Buttons EJECT Button Press to eject the tape. SPEED Button Press to select the recording speed (SP, LP, or SLP). POWER Button Press to turn on or off the TV/VCR, Cable Box, or Direct Broadcast System. (You must first press the COMBI or CABLE/DBS button.) Details are on pages 20 - 21. SLEEP Button Press to set the sleep timer. Details are on page 44. PLAY/▲ Button Press to play a tape. Details are on page 31.
CCZ134comb 4/5/99 9:30 PM Page 25 Remote Control Buttons (cont’d) 25 PAUSE/STILL Button During recording, press to temporarily stop the recording. Press again to resume recording. Details are on page 32. You cannot pause a One-Touch Recording. During tape playback, press to freeze the picture (still). Details are on page 54. MEMORY Button Press to memorize a tape position at which the real-time counter was set to 0:00:00. Details are on page 51.
CCZ134comb 4/5/99 9:30 PM Page 26 26 Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 1 Press the COMBI button, then press the MENU button. TO ADJUST PRESS { / B EJECT K K POWER > BRIGHTNESS PICTURE COLOR TINT SHARPNESS CHANNEL SLEEP SPEED MEMORY PAUSE/STILL REC/OTR 2 3 Press the PLAY/▲ button or the STOP/▼ button to select the desired control (BRIGHTNESS, for example). 3 1 PLAY REW F.
CCZ134comb 4/5/99 9:30 PM Page 27 Smart Picture 27 The Smart Picture feature allows you to improve the TV/VCR’s picture when viewing sports, a movie, or video games; to improve the picture when the antenna/cable signal is weak; or to reset the picture controls to their original settings. 1 Press the SMART PICTURE button repeatedly until the Smart Picture mode you want appears on screen. The following options will be available.
CCZ134comb 4/5/99 9:30 PM Page 28 28 Remote Locator Your TV/VCR can find your remote control for you. When you press the POWER button on the TV/VCR to turn on the TV/VCR, your remote control beeps and LOCATING REMOTE appears on-screen. The remote control will beep for about 30 seconds. Or, press any button on the remote control to stop the beeping. If another remote control beeps ... 2-3 If another remote control beeps... The TV/VCR may find other remote controls.
CCZ134comb 4/5/99 9:30 PM Page 29 On-Screen Status Displays 29 A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below. If you select STATUS ON, then select COUNTER ONLY OFF: ● Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds.
CCZ134comb 4/5/99 9:30 PM Page 30 30 Reminder The channel number will remain on-screen at all times when you set REMINDER to ON in the pop up menu. The exception is during tape playback, Forward and Reverse Searching and Still modes, and when closed captioning is selected (CAPTION in the pop up menu). Set REMINDER to ON or OFF by following the steps below. 1 SLEEP Press the COMBI button, then press the MENU button.
CCZ134comb 4/5/99 9:30 PM Page 31 Playing 31 Follow the steps below to play a tape. 1 Insert a tape in the TV/VCR. The power will come on. If the tape’s record tab has been removed, playback should start automatically. 1 Insert a tape in the TV/VCR. EJECT POWER 2 If playback does not start automatically, press the COMBI button, then press the PLAY/▲ button to start playback. 3 4 SLEEP SPEED MEMORY PAUSE/STILL REC/OTR 4 PLAY REW F.
CCZ134comb 4/5/99 9:30 PM Page 32 32 Recording Read and follow the steps below to record a TV program. 1 Press the COMBI button, then place a tape with its record tab intact (see page five) in the TV/VCR. The power will come on. Or, if the tape is already in the TV/VCR, press the POWER button to turn on the TV/VCR. 2 Press the SPEED button until the desired tape speed appears on the TV/VCR screen. Details about tape speed are given below. 3 Use the CH(annel).
CCZ134comb 4/5/99 9:30 PM Page 33 One-Touch Recording 33 The One-Touch Recording (OTR) function allows you to program an immediate timed recording from 30 minutes to eight hours long without setting the timer. Before you begin, make sure: ● Channels are set up. ● There is a tape in the TV/VCR. The record tab must be intact. 1 EJECT POWER Press the COMBI button, then use the CH(annel). Up/Down buttons or the Number buttons to select the channel you want to record.
CCZ134comb 4/5/99 9:30 PM Page 34 34 Rerecording (Tape Duplication) AUDIO and VIDEO OUT Jacks on source unit (VCR or Camcorder) AUDIO VIDEO EARPHONE STOP/EJECT VIDEO AUDIO OUT IN Audio Cable (white) from AUDIO OUT to AUDIO Video Cable (yellow) from VIDEO OUT to VIDEO AUDIO and VIDEO Jacks on TV/VCR 1 Make the connections shown above, using audio and video cables. (Make sure the source unit is connected to a power source.) 2 The source unit (VCR or camcorder) will play your tape.
CCZ134comb 4/5/99 9:30 PM Page 35 Timer Recording 35 2-3 Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears. ● Channels are set up. ● There is a tape in the TV/VCR. (Make sure the tape’s record tab is intact and the tape is long enough to record the program.
CCZ134comb 4/5/99 9:30 PM Page 36 36 Timer Recording (cont’d) 4 Use the Number buttons (1 - 8) to select a position in which to store the timer recording. Flashing numbers indicate an open position (one in which a timer recording has not yet been stored). NOTE: If you select a number that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on-screen for a few seconds. Then information about the program in that position will appear on-screen.
CCZ134comb 4/5/99 9:30 PM Page 37 Timer Recording (cont’d) 37 8 Press the Number 1 button to record in SP speed, press the Number 2 button to record in LP speed, or press the Number 3 button to record in SLP speed. Details about tape speed are on page 32. You cannot use the SPEED button at this time.
CCZ134comb 4/5/99 9:30 PM Page 38 38 Timer Recording (cont’d) Checking or Clearing Timer Recordings 1 2-3 With the TV/VCR on, press the COMBI button, then press the MENU button. 2 Press the PLAY/▲ button or the STOP/▼ button to select VCR PROGRAM, then press the F.FWD/B button. 3 Press the PLAY/▲ button or the STOP/▼ to select PROGRAM REVIEW, then press the F.FWD/B button. The timer recording information for the program in the lowest numbered position will appear on-screen.
CCZ134comb 4/5/99 9:30 PM Page 39 Setting Up the VCR Plus+ Programming System 39 1 First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR Plus+ programming system to work properly. Since the channel numbers of the stations you receive may not be the same as the station numbers, and since channel numbers differ from area to area, you must program the TV/VCR with your local channel information.
CCZ134comb 4/5/99 9:30 PM Page 40 40 Setting Up the VCR Plus+ Programming System (cont’d) 2 Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. You’ll notice that some stations have VCR Plus+ and Cable/TV channel numbers that are the same, and other stations have channel numbers that do not match. Where the channel numbers DO NOT match, you must tell the TV/VCR the VCR Plus+ and Cable/TV channel numbers according to the following steps.
CCZ134comb 4/5/99 9:30 PM Page 41 Timer Recording With the VCR Plus+ Programming System 41 Follow the steps below to program a timer recording using the PlusCode programming numbers in your TV guide. Before you begin, make sure: ● The clock has been set. If not, CLOCK MUST BE SET appears. ● Channels are programmed. ● There is a tape in the TV/VCR (make sure the tape’s record tab is intact and the tape is long enough to record the program). ● You have completed the steps on pages 39-40.
CCZ134comb 4/5/99 9:30 PM Page 42 42 Timer Recording With the VCR Plus+ Programming System (cont’d) 4 Press the Number 1 button to record in SP speed, the Number 2 button to record in LP speed, or the Number 3 button to record in SLP speed. Your selection will appear to the right of REC SPEED on-screen, although SP=1 LP=2 SLP=3 will continue to flash. For details about tape speed, see pages 32 and 55. You cannot use the SPEED button at this time.
CCZ134comb 4/5/99 9:30 PM Page 43 Defeat Recording 43 Follow the steps below to prevent accidental recording. 1 2-3 Press the COMBI button, then press the MENU button. EJECT POWER > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS SLEEP SPEED MEMORY PAUSE/STILL REC/OTR PLAY REW 2 F.FWD STOP Press the PLAY/▲ button or the STOP/▼ button to select VCR SETUP, then press the F.FWD/B button. VCR SETUP > ONE TIME PLAY 1 MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 A.
CCZ134comb 4/5/99 9:30 PM Page 44 44 Setting the Sleep Timer Use the sleep timer to program the TV/VCR to shut off in a certain amount of time. 1 Press the COMBI button, then press the SLEEP button. The sleep timer display will appear on-screen. (You can not set the sleep timer during a recording.) 1-2 EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR PLAY SLEEP 0 MIN REW F.
CCZ134comb 4/5/99 9:30 PM Page 45 Closed Caption 45 When you watch a program that is being broadcast with closed captions, you can access on-screen boxes containing the program’s dialogue (for example, what a character is saying), dialogue in a foreign language, or information (such as a channel guide, schedule, or announcements). Follow the steps below to select closed captions. Not all TV programs and commercials are broadcast with closed captions.
CCZ134comb 4/5/99 9:31 PM Page 46 46 Closed Caption (cont’d) 4 Press the STATUS/EXIT button. The type of closed captions you selected at step 3 will appear on-screen. EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR PLAY REW F.FWD STOP MENU HELLO Standard Closed Captions 4 STATUS/EXIT 1 2 3 4 5 6 7 8 9 A.CH 0 +100 CABLE/DBS COMBI CH. WORLD WEATHER NYL LOS LONDON CLOUD RAIN CLOUD 5C 8C 7C 23:00 20:00 4:00 CLEAR VOL. VAR.SLOW VCR PLUS+ /ENTER MUTE TRACKING F.
CCZ134comb 4/5/99 9:31 PM Page 47 Volume Bar 47 Usually, the volume bar appears when you press the VOL(ume). Up/Down buttons. If you do not need it, set the VOLUME BAR to OFF position. For example, when you watch a program that is being broadcast with closed captions, you may choose to set the VOLUME BAR to OFF so the captions can remain on-screen. The captions will remain on-screen even when you press the VOL(ume). Up/Down buttons or the MUTE button.
CCZ134comb 4/5/99 9:31 PM Page 48 48 Repeat Play Follow the steps below to program the TV/VCR to play a tape over and over. 1 2-3 Press the COMBI button, then press the MENU button. EJECT POWER > PRIM. SETUP PRESS B SLEEP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS SPEED MEMORY PAUSE/STILL REC/OTR PLAY REW F.FWD STOP 2 Press the PLAY/▲ button or the STOP/▼ button to select VCR SETUP, then press the F.FWD/B button. 1 MENU STATUS/EXIT 1 2 3 4 5 6 7 8 9 A.
CCZ134comb 4/5/99 9:31 PM Page 49 A - B Repeat Play 49 Follow the steps below to program the TV/VCR to play the material between two specified points (A and B) on a tape over and over again. 1 Insert a tape in the TV/VCR. 3-4 1 2 Insert a tape in the TV/VCR. EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR Press the COMBI button, then press the MENU button. PLAY REW F.FWD STOP > PRIM.
CCZ134comb 4/5/99 9:31 PM Page 50 50 A - B Repeat Play (cont’d) 6 Press the STATUS/EXIT button to remove the display. AB REPEAT will appear on-screen. Beneath it, the letter A will flash beside the real-time counter. 7-8 . EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR A A-B REPEAT 1:23:45 PLAY 7 REW F.FWD STOP MENU Play, fast forward, or rewind the tape to the position at which you want to begin playback. Stop the tape, then press the MEMORY button to set the start position (A).
CCZ134comb 4/5/99 9:31 PM Page 51 Real-Time Counter Memory 51 Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 1 Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. 1&5 2 EJECT POWER SLEEP Press the STATUS/EXIT button. The real-time counter will appear on-screen. SPEED MEMORY PAUSE/STILL REC/OTR 4 PLAY 01:08 PM CH10 STOP REW F.
CCZ134comb 4/5/99 9:31 PM Page 52 52 Index Search This feature allows you to index the starting points of programs that you have recorded on a tape. Then, you can easily rewind or fast forward to that point. Example: If you are watching program number 4 and you want to fast forward to program number 7, skip three programs. EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR CURRENT PLAYBACK PROGRAM Beginning of tape End of tape 3 Pro. 1 Pro. 2 Pro.3 Pro. 4 Pro. 5 Pro. 6 Pro.
CCZ134comb 4/5/99 9:31 PM Page 53 Automatic Operation Features 53 The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab intact. If a timer recording is set and the VCR power is off, the TV/VCR will eject the tape if the record tab is missing.
CCZ134comb 4/5/99 9:31 PM Page 54 54 Playback Options Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD/B button or the REW(ind)/{ button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/▲ button. EJECT POWER SLEEP SPEED MEMORY PAUSE/STILL REC/OTR PLAY Super High Speed Searching (LP/SLP) REW F.FWD STOP 1 During tape playback, press the F.FWD/B button or the REW(ind)/{ button, then press again.
CCZ134comb 4/5/99 9:31 PM Page 55 Specifications / Glossary 55 Specifications Glossary General CRT: 13-inch in line gun Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Four heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.67 mm/sec. SLP: 11.12 mm/sec.
CCZ134comb 4/5/99 9:31 PM Page 56 56 Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is displayed on the back of the product.
CCZ134comb 4/5/99 9:31 PM Page 57 Helpful Hints (cont’d) 57 The remote control is not available, or the remote control will not access the pop up menu. • Use the buttons on the front panel of the TV/VCR to access the pop up menu (page 22). You can not enter numbers (for example, to program a timer recording) using the front panel buttons. TV/VCR has no power. • Make sure the power plug is completely connected to an AC (alternating current) outlet. TV/VCR power shuts off after 15 minutes.
CCZ134comb 4/5/99 9:31 PM Page 58 58 Limited Warranty TV/VCR COMBINATION 90 Days Free Labor/One Year Free Parts Exchange (Two Years Free Exchange on Color Picture Tube) This product must be carried in for repair. WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product.
CCZ134comb 4/5/99 9:31 PM Page 59 Index 59 a-b repeat play . . . . . . . .49 - 50 accessories . . . . . . . . . . . . . . .60 ant(enna) jack . . . . . . . . . . .6, 23 audio jack . . . . . . . . . . .7, 22, 34 automatic playback . . . . . . . . . . . . . . .53 rewind . . . . . . . . . . . . . . . .53 batteries . . . . . . . . . . . . . . . . . .5 brightness, adjusting . . . . . . . .26 cable/dbs button . . . .20 - 21, 25 channel above 100 . . . . . . . . . . . . .24 adding . . . . . . . . . . . . . . . .
4/5/99 9:31 PM SUPPLIED ACCESSORIES CCZ134comb Page 60 Check to be sure the items on this page are packed with your TV/VCR. These accessories are provided to help you use or set up your TV/VCR. Remote Control (4835 218 37226) Three AA Batteries (4835 138 17012) If any of these items are not included, or if you need to replace an item, contact Philips Service Solutions Group at the address below. Philips Service Solutions Group P.O. Box 967 Greeneville, TN 37744-0967 Or, call 1-800-851-8885.