Operation Manual
• 22 •
B be deactivated by pressing the " " button while the " "
light (14) is blinking or steady-on. In this case the "
" light
(18) turns o .
Note: if the rinsing procedure is deactivated,
it can be reactivated only by pressing the "
"
button.
6 Energy Saving
The machine is designed for energy saving.
After 9 minutes of inactivity, the machine turns o in order to
save energy and respect nature.
Press the ON/OFF "
" button (10) to operate the machine.
7 Coffee Brewing
Warning! During the co ee brewing it is forbid-
den to remove the pressurized lter holder by
manually turning it clockwise. Danger of burns!
• During this operation, the "
" light (14) is blinking; this is
to be considered as a standard and not a faulty operating
mode.
• Before using the machine, make sure that there is enough
water in the machine tank.
Note: if the steam knob is opened by mistake
during the warm-up phase, the "
" light (16)
starts blinking. Close the knob and wait until the ma-
chine is ready.
If co ee is NOT brewed after pressing the brew
button "
" (11), press the "co ee cup" brew
button (11) again and check the "Troubleshooting" ta-
ble before removing the lter holder.
Ensure the machine is ready before brewing co ee. The ma-
chine is ready when the "
" light (14) is steady on.
7.1 Filter Holder Warm-Up
If the "rinse" function is not activated and/or the lter holder is
to be warmed-up manually, do as follows:
•
13
Insert the pressurized lter holder into the brew unit
(4) from the bottom.
•
14
Turn the pressurized lter holder from left to right
until it locks into place. Release the pressurized lter
holder grip. The handle will turn slightly to the left. This
movement guarantees optimum lter holder performance.
•
17
Preheat the pressurized lter holder by pressing the "
" button; some water will ow out of the pressurized
lter holder (this operation is necessary only for the rst
co ee).
• After 50cc of water have been dispensed, press the "
"
button again to stop the dispensing procedure.
•
19
Remove the pressurized lter holder by turning it from
right to left and then drain the remaining water.
Place a container under the dispensing spout.
Now you can go on with the co ee brewing procedures de-
scribed in the following sections.
7.2 Using Ground Co ee
•
7
Insert the lter (22) in the pressurized lter holder
(19); the lter is already inserted when using the machine
for the rst time. As the machine is tted with the special
lter (22), there is no need to change the lter to prepare
either one or two co ees.
•
8
Add 1-1.5 measuring scoop(s) for a single co ee and 2
measuring scoops for a double co ee. Remove any co ee
residues from the rim of the pressurized lter holder.
Note: do not press the co ee, since the lter
holder is provided with an optimized system
for original espresso brewing.
•
13
Insert the lter holder (19) into the brew unit (4) from
the bottom.
•
14
Turn the lter holder from left to right until it locks
into place.
•
16
Take 1 or 2 preheated cups and place them under
the pressurized lter holder. Make sure that they are
placed correctly under the co ee brewing nozzles.
•
17
Press the " " button.
•
18
When the desired quantity of co ee has been
brewed, press the "
" button again to stop the brewing
procedure. Wait for a few seconds after brewing, then
remove the cups of co ee.
•
19
After brewing, wait until the
" " light (14)
stops
blinking, then remove the pressurized lter holder by
turning it from right to left and empty the remaining
co ee grounds.