Introduction The PHILIPS 104B color monitor displays sharp and brilliant images of text and graphics with a maximum resolution up fo 1024x768 pixels. It is optimal for Windows, spread sheets, and any other application. This monitor automatically scans horizontal frequencies from kHz to kHz, and vertical frequencies from 50Hz to 110Hz.
Note: I you experienced your monitor display Is changing from color to omen, it's possible that you are using a non-VASE-DDC-standard video card. Please consult with your locate Philips dealer for more information. As an Energy Star Partner, PHILIPS, has determined that this product mils the Energy Star guidelines for energy efficiency. 1BM, 1BM PC and Power PC are registered trademarks of international Business Machines Corporation.
Safety precautions and maintenance 4 Disconnect the monitor from the mains supply if the monitor is not to be used for an extended period of teems. # Do not attempt to remove the back cover, as you will be exposed to @ shock hazard. The back cover should ably be removed by qualified service personnel. <+ Do not place objects on top of the monitor cabinet, which could fall into vents or which could cover them and prevent paper cooling of the monitor's electronic devices.
00 Installation important: Please refer fo the user's manuals of your computer and video adapter to make sure these equipment are properly installed and configured before installing the monitor. Positioning / Ventilation + Avoid exposing the monitor to direct sunlight, stoves or any other heat sources. 4 To prevent overheating, make sure that the ventilation openings of the monitor are not covered. 4 Keep moisture and dust away.
Connection important: Please make sure the AC power 1o your computer is “QFF” before connecting or disconnecting any display peripheral, Allure to do so may cause serious personal injury as well as permanent damage to your computer equipment. inch! Based platform: 386, 486, Pentium, or other compatibles: * Connect the monitor to the computer using the supplied interface cables.
Connection to the mains (Rear of the mono Connecting to the mains This monitor is set fo operate at a mains supply of 100-240 valid AC {14B1320W/14B1320T); 220-240 volts AC (14813205}, If the mains vantage in your home is not between this, consult your dealer. Connect one end of the mains cord o the mains socket at the rear of monitor, and the other end to the mains supply. The monitor will be operating in power saving mode if you switch on your monitor without signal Input from PC.
Front Control locations and functions o, For an optimized adjustment of the picture following controls are available at the front. (D POWER. ® Press this knob, the green LED lights and the power is ON. ® Press this knob again, the green LED disappears and the power is OFF. () CONTRAST @ Seditious adjust the picture contrast level. & BRIGHTNESS » Used to adjust the overall screen brightness as a compensation for ambient light. Tress adjust the selected function.
‘The function pads: {fn H-Shift : to adjust the horizontal position of the image. & H-Size : to adjust the horizontal amplitude of the image. & V-Shift : to adjust the vertical position of the image. &) V-Size : to adjust the vertical amplitude of the image. Remarks: 1. When pressing any function pad, the "Shift" LED will flash one to indicate the function has been selected. 2. Once the limit of the adjustable range has been reached, the shift LED will flash continuously.
Adjustment The monitor is per-set with 8 dames for optimal display size and centering as indicated in the following table: Resolution | Horizontal | Vertical Mode l{dots x lines}! | Remark VGA 640 ¥ 350 315 70 Non-interlaced VGA 640 x 400 31.5 70 Non-interlaced VGA 640 x 480 815 80 Non-interlaced VESALIUS 1640 X 480 375 75 Noninterference VESALIUS | 800 x 600 7.8 80 Non-interlaced VESALIUS 1800 x 600 46.9 75 Non-interlaced VESALIUS 11024 X768 483 80 Non-interlaced VESALIUS 1800 x 800 53.
(B) Power Management Signaling Power Management Definition VASE DIMS POWER SAVING STATES MODE |VIDEO | POWER USED | POWER SAVING(%) ON Active Yes | Yes | «wallets 0% Stand-by| Blanked| No | Yes | Walters >82% Suspend | Blanked| Yes | No <15 Walt » 2% OFF _ blanket Walt > 94% Note: The video will be blanked and the power LED color will change into following colors whenever the monitor goes into power management status.
Technical information (1} Gene rah Picture tube : 14 inch {35.5 om), 90° deflection, non glare, back ma lix light transmission 57%, phosphor P22 medium sheet, dotted pitch 0.28 mm. Screen area Recommended Display Area: 250 mm (H) x 188 mm (V) Maximum Display Area © 274 mm {H) x 201 mm (V) Line (Horizontal) frequency KHz (automatically) Raster {(Vertical) frequency @ 50 110 Mz {automatically) Mains voltage © 100 240 VAC .
{111} Pin assignment: (1) The 15-pin D-sub connector (male} of the signal cable (IBM systems). Pin No. | Assignment Pin No. | Assignment i Red video input 9 No pin 2 Green video input 10 Logic ground 3 Bite video input 11 identification output 4 identification output connected to pin 10 ~ Connected to pin 10 12 Striae data ling (SDA) 5 Ground 13 H. Synge 6 Red video ground 14 | V.
(information for UK only) WARNING THIS APPLIANCE MUST BE EARTHED. Important: ‘This apparatus is supplied with an approved molded 134 plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 BAAS.T.A, or BSI approved type. 3. Refit the fuse cover. 1f the fitted plug is not suitable for your socket outlets, it should be cul off and an appropriate 3-pin plug fetid in its place.