electronic user's manual file:///D|/EDFU/crt_17/edoc/english/107E/manual.
Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.
About This Electronic User's Manual About This Electronic User's Manual About This Guide • Other Documents You May Need • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips Color Monitor. It describes the monitor's features, setup, operation and all other information, which is the same exact information described in our printed version.
About This Electronic User's Manual Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data.
107E Product Information Product Information Product Features • Technical Specifications • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Product Features 107E5 ● 17-inch (16.
107E Product Information VIDEO • Video dot rate 108 MHz • Input impedance - Video 75 ohm - Sync 4.7 kOhm • Input signal levels 0.7 Vpp • Sync input signal Separate sync • Sync polarities Positive and negative WHITE COLOR TEMPERATURE Chromaticity CIE coordinates: • at 9300 degrees K x = 0.283 / y = 0.297 • at 6500 degrees K x = 0.313 / y = 0.329 sRGB sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.
107E Product Information If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or other input device is detected, the monitor will automatically "wake up".
107E Product Information Pin Assignment The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin Assignment No. Pin Assignment No. 1 2 Red video input Green video input 9 10 +5V DDC supply Logic ground Identical output - connected to pin 10 3 Blue video input 11 4 Identical output - connected to pin 10 12 Serial data line (SDA) 5 6 7 Ground Red video ground Green video ground 13 14 15 H. Sync / H+V V.
Installing your Monitor Installing your Monitor Front View • Rear View • 6G3B11 Multimedia Base (option) Front View Power button switches your monitor on. OK button which when pressed will take you to the OSD controls Contrast hotkey. When the "-" button is pressed, the adjustment controls for the CONTRAST will show up. Brightness hotkey. When the "+" button is pressed, the adjustment controls for BRIGHTNESS will show up. file:///D|/EDFU/crt_17/edoc/english/INSTALL_6/INSTALL.
Installing your Monitor "-" and "+" buttons, are used for adjusting the OSD of your monitor. LightFrame™ hotkey. When the button is pressed, the high-brightness function of LightFrame™ will show up. RETURN TO TOP OF THE PAGE Rear View file:///D|/EDFU/crt_17/edoc/english/INSTALL_6/INSTALL.
Installing your Monitor 1. Power in - attach power cable here. 2. Video In - this is a cable which is already attached to your monitor. Connect the other end of the cable to your PC. RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_17/edoc/english/INSTALL_6/INSTALL.
On-Screen Display On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display RETURN TO TOP OF THE PAGE The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments. file:///D|/EDFU/crt_17/edoc/english/OSD_2/OSDDESC.
On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_17/edoc/english/OSD_2/OSDDESC.
Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO READ THE WARRANTY COVERED: WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Turkey • Bulgaria LATIN AMERICA: Antilles • Argentina • Brazil • Chile • Colombia • Mexico • Paraguay • Peru • Uruguay • Venezue
Frequently Asked Questions Frequently Asked Questions 1. What does the "Designed for Windows" logo signify? The "Designed for Windows" logo means your Philips monitor fulfills the requirements and recommendations of the PC9x (97, 98, or 99) System Design Guide and passes stringent WHQL tests. 2. What is USB? Think of USB as a smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals.
Frequently Asked Questions monitor to your Mac system. Please contact your dealer/reseller for details. 7. What is TCO? TCO is a Swedish abbreviation for the Swedish Confederation of Professional Employees. 8. What is MPR? MPR is a Swedish abbreviation for the Swedish National Board of Measurement and Testing. 9. What are the differences between MPRII, TCO92, TCO95, TCO99 and TCO'03? In the general hierarchy of standards, TCO'03/TCO99 is the highest level of certification.
Frequently Asked Questions Visual Ergonomics: MPRII: No requirement. TCO92: No requirement. TCO95: Set ergonomic rules including minimum contrast level, flicker and jitter. TCO99: Tightened TCO95 rules. TCO'03: Tighten TCO99 rule for CRT and new requirement of screen color for TFT LCD Monitors. Ecology: MPRII: No requirement. TCO92: No requirement. TCO95: Set general ecological standards including recycling preparation, environmental policy and environmental certification.
Frequently Asked Questions 12. Why does the picture on the screen appear to flicker? A low refresh rate or electrical interference typically causes flickering in the picture. Possible solutions include the following: ● Verify that the proper drivers are installed for your video card ● Make sure that all electrical devices (such as mobile phones) are at least 1m from the monitor ● Place the monitor in another physical location away from electrical interference ● Adjust the refresh rate to 75hz or higher.
Frequently Asked Questions LightFrame™ consists of a software application and an Integrated Circuit (IC) embedded in the monitor. Together, they boost brightness and sharpness in a user defined window or screen area. Unique LightFrameTM technology dramatically improves photo and video display quality. 18. Why is LightFrame™ important to me? With LightFrame™, selected Philips monitors deliver TV quality video and photo display while maintaining monitor performance for text-based applications.
Frequently Asked Questions 22. What will happen when my system is no longer connected to a LightFrame™ enabled monitor - for example, when I take my notebook on the road? Philips exclusive LightFrame™ feature requires the combined operation of hardware that resides in your monitor and software installed on your system. It only works when a monitor with built-in hardware receives commands from system software.
Frequently Asked Questions The following models can be incorporated with the Multimedia Base: 109B5, 109E5,109F5, 107B5, 107E5,107F5, 107S5, 107T5. 27. What are Philips Multimedia Base's specifications? See detailed Multimedia Base specifications on the product information page. 28. Why is a Multimedia Base better than separate speakers? The major advantage of the Multimedia Base is its minimal space requirements. In fact, it hardly uses any extra space at all: monitor depth and width are unchanged.
Frequently Asked Questions 32. How does Auto Calibrate work? During the calibration process, different predefined black and white images are displayed on thescreen. The beam currents of the red, green and blue cannon are accurately measured and compared to the original values stored in the monitor. By readjusting gain values of the individual cannons, deviation is reduced to zero. Default values are stored during production.
Frequently Asked Questions ● newer models have this option in the On Screen Display under Input Signal Selection. Video card may be not a VESA standard (try the monitor with another computer) 37. Why does my monitor display "Out of Range"? The video card installed in your computer may be too high for the monitor 's specifications. Please contact your computer manufacturer for details on how to lower resolution for your operating system. 38.
Frequently Asked Questions Yes, when degaussing your monitor via the OSD, it is normal for the monitor to make a relatively loud noise. Please be aware that many models will not degauss more than once within any given time period (up to 10 minutes). This is due to the unit having a temperature sensitive resistor. While the unit is degaussing, the resistor increases in value with heat and once it reaches a certain temperature, the resistance will rise and prevent voltage from reaching the degaussing coil.
Frequently Asked Questions Select under Advanced Controls in the monitor 's OSD. Most computers require it to be set at 0.7V.
Frequently Asked Questions ● ● ● ● Reboot your computer while holding the Ctrl key on your computer. If you see any picture during the boot procedure, please verify the settings of your video card (for Windows go to Control Panel and select Display). Check that the video cable is not damaged, bent or that any of the pins in the connector are damaged (please be aware that some VGA connectors have one missing pin). If damaged, replace with a new cable.
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ A Autoscan A microprocessor-based feature of Philips Brilliance monitors is able to detect automatically horizontal and vertical frequencies of input signals with those of the installed video card. An autoscan monitor can thus operate with a wide range of video cards. MultiSync, a registered trademark of NEC, provides a similar function.
Glossary C CE Mark CE mark is displayed on products per EMC and LV ( low Voltage Device ) directives in compliance with European Community safety, EMI and EMS requirements and is compulsory on products for sale in the European Community. Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source.
Glossary Points where convergence error is specified. Convergence-error correction A method of correcting for convergence error to insure that all three beams land simultaneously in the same triad. This is usually accomplished by means of special convergence-error correction coils in the deflection yoke. CRT Cathode-ray tube - the general term for all tubes in which one or more electron beams emitted by a cathode are periodically scanned across a phosphor screen by means of deflection circuitry.
Glossary controller to be automatically configured to make optimal use of the display without manual user interaction. DDC is implemented as part of the new Plug & Play approach introduced into the PC market to increase user friendliness. The three levels developed for Plug & play are: (1) DDC1, monitor send data to the PC; (2) DDC2B, PC can request information from monitor; and (3) DDC2Bi which is a two-way communication - monitor can be addressed and PC or graphics board can give commands to monitor.
Glossary Dot rate Frequency in MHz of the dot clock. It is a measure of the speed with which data is transferred between the video card and subsequent processing circuitry. Also known as video dot rate. RETURN TO TOP OF THE PAGE E Electromagnetic radiation standards International standards set to limit electromagnetic emissions from monitors. There are currently two important standards both derived from regulations originally laid down by Swedish authorities.
Glossary In 1991, the Swedish Tjänstemannens Central Organization (TCO, Swedish confederation of Professional Employees ) set a standard even more severe than MPR-II, especially for alternating electric fields (AEF). The TCO standard is more severe since not only are the permitted field levels reduced compared with MPR-II, but the measuring distance is also reduced (see table).
Glossary Also called line frequency and expressed in kHz, it is the number of video lines written on the screen every second (from left to right). The higher the horizontal scanning frequency, the better the resolution (i.e., the higher the resolution and/or the higher the refresh rate). RETURN TO TOP OF THE PAGE I INF File INF file (Information File) Information (INF) files store information in a specific format.
Glossary L Linearity The degree to measure the actual location of a pixel on the screen corresponds with its intended location. ( see figure ) Line frequency See Horizontal scanning frequency. Low-emission monitor A monitor that complies with international standards on radiation. See Electromagnetic radiation standards. Low-frequency electric and magnetic fields Alternating fields generated by the deflection yoke.
Glossary M Moiré effect A fringe pattern arising from the interference between two superimposed line patterns. In a monitor it comes from the interference between the shadow mask pattern and the video information (video moiré), and between the shadow mask pattern and the horizontal line pattern (scan moiré). It shows itself as wavy patterns on the screen and becomes more noticeable as monitor resolution increases. Since the video signal varies continuously, little can be done about video moiré.
Glossary screen area, resulting in an image that is smaller (and less legible) than it needs to be. RETURN TO TOP OF THE PAGE P Parallelogram Distortion See Geometric distortion. Phosphor Generic name for the class of substances that exhibit luminescence. To produce a picture on screen, phosphors are deposited on the inner surface of the picture-tube screen and excited into luminescence by the electron beam.
Glossary R Raster The area on screen that electron beam can reach. Refresh rate See Vertical scanning frequency. Resolution The number of pixels that can be displayed on the screen. The resolution is specified as the number of pixels in a line multiplied by the number of horizontal lines. See also video graphic adapter. Rotation function The feature that allows users to adjust the whole screen rotating to be horizontal.
Glossary Anti-Static coatings Due to bombardment by beam electrons, monitor screens become electrically charged when in use. Electrically charged screens surfaces can attract dust particles. An Anti-Static coating is a conductive coating deposited on the screen (or on a glass panel immediately in front of the screen) that conducts away the charge and prevents screen dust build-up.
Glossary The ARAS coating reflects only about 0.5% of the incident light. AGRAS (Anti-Glare anti-Reflection Anti-Static) coating. A combined anti-reflection, anti-glare, anti-static coating. Self-test function A monitor equipped with hardware or software to automatically detect cable connection status. Shape Deviation of a reproduced picture from its intended shape. The following types of distortion are most common: file:///D|/EDFU/crt_17/edoc/english/GLOSSARY/GLOSSARY.
Glossary SOG (Synchronization On Green) A properly functioning color monitor requires five kinds of signals: horizontal sync pulse, vertical sync pulse, red color signal, green color signal and blue color signal. Signals from a PC are transmitted to a monitor using one of three methods: 1. Separate sync: Horizontal and Vertical sync signals transmitted separately 2. Composite sync: Horizontal and vertical sync pulses mixed into a single signal train. 3.
Glossary See rotation function. Trapezoid distortion See Geometrical distortion. TTL signal A TTL (Transistor-transistor-logic) signal is a digital signal level for controlling the screen colors. With TTL driving, the red, green and blue signals can only be switched on or off or provided with an intensity signal. A TTL-driven monitor can thus display a maximum of 64 colors. Video standards such as MDA, CGA and EGA are based on TTL level.
Glossary signaling. A hub consists of two portions: the Hub Controller and Hub Repeater. The repeater is a protocol-controlled switch between the upstream port and downstream ports. It also has hardware support for reset and suspend/resume signaling. The controller provides the interface registers to allow communication to/from the host. Hub specific status and control commands permit the host to configure a hub and to monitor and control its ports.
Glossary V Vertical dot pitch See Dot pitch. Vertical scanning frequency Expressed in Hz, this is the number of fields written to the screen every second in interlaced mode. In non-interlaced mode vertical scanning frequency is the number of frames (complete pictures) written to the screen every second (also known as refresh rate). Vertical sync pulses A train of square shaped waveforms that define the start of a new frame.
Glossary resolutions from 1280 x 1024 to 1600 x 1280, horizontal line frequencies up to 90 kHz and bandwidths up to 200 MHz. VIS (Viewable Image Size) The real screen dimensions that users can see measured diagonally. The VIS of a monitor is always less than the so called screen size of a monitor. For example, the VIS of a 17-inch monitor is only about 16 inches. It depends on the useful screen size of CRT and the opening of a monitor's front cabinet.
Download and Print Download and Print This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard disk, then viewed and printed with Acrobat Reader or through your browser. If you do not have Adobe® Acrobat Reader installed, click on the link to install the application. Adobe® Acrobat Reader for PC / Adobe® Acrobat Reader for Mac. Download instructions: To download the file: 1. Click-and-hold your mouse over the icon below. (Win95/98 users right-click) 2.
Download and Print 107X.pdf file:///D|/EDFU/crt_17/edoc/english/DOWNLOAD/DOWNLOAD.
Troubleshooting Troubleshooting Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Other Related Information Common Problems Having trouble? Something not working? Before calling for help, try these suggestions. Having this problem? No Picture Check these items ● Make sure the Power cable is plugged into the power outlet and back of the monitor. ● Power button on the front of your monitor should be in the ON position.
Troubleshooting ● Dim Picture ● Picture is too large or too small. ● Adjust the Brightness and Contrast controls. Check your video card and it's owner's manual instructions for it may be a non-VESA-DDC Standard card. ● Adjust the Horizontal and/or Vertical Size. Adjust the Zoom. ● Adjust the geometry. ● Eliminate the use of a video extension cable and/or video switch box. ● Face the monitor toward the East for the best picture quality. ● ● Check to make sure Moiré is switched off.
Regulatory Information Regulatory Information TCO '95/99 Information • TCO'95/99 Environmental Requirements • TCO '03 Information • Recycling Information for Customers • CE Declaration of Conformity• Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
Regulatory Information TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety.
Regulatory Information Cadmium** Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO' 95/ TCO'99 requirement states that batteries, the color-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches.
Regulatory Information Some of the features of the TCO'03 Display requirements. Ergonomics ● Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability.
Regulatory Information There is currently a system of recycling up and running in the European countries, such as The Netherlands, Belgium, Norway, Sweden and Denmark. In U.S.A., Philips Consumer Electronics North America has contributed funds for the Electronic Industries Alliance (EIA) Electronics Recycling Project and state recycling initiatives for end-of-life electronics products from household sources.
Regulatory Information and Emission, TCO: Swedish Confederation of Professional Employees) for TCO versions RETURN TO TOP OF THE PAGE Energy Star Declaration PHILIPS 107E5* This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94.
Regulatory Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Regulatory Information Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement. N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques. CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.
Regulatory Information RETURN TO TOP OF THE PAGE MIC Notice (South Korea Only) Class B Device Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket).
Regulatory Information RETURN TO TOP OF THE PAGE North Europe Information (Nordic Countries) Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. file:///D|/EDFU/crt_17/edoc/english/107E/SAFETY/regs/regulat.
Regulatory Information Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
Regulatory Information Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge). Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger. ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
Regulatory Information outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.
Regulatory Information RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_17/edoc/english/107E/SAFETY/regs/regulat.
Other Related Information Other Related Information Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Information for Users in the U. S. • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
6G3B11 Multimedia Base (option) 6G3B11 Multimedia Base (option) Front View • Rear View • Technical Specifications • Description of the Controls • Installing your Multimedia Base • Power adapter Installation Technical Specifications* • Output power 2 x 1.5W RMS / 36W PMPO • Bass Boost • Headphone connection 3.5 mm jack • Microphone in/out 3.5 mm jack • Includes Audio cable and AC adapter • Dimension 9.4" x 2.1" x 8.
6G3B11 Multimedia Base (option) D. Microphone jack Attach your microphone here. E. Audio In Connect this to the audio output of your PC. F. MIC Out Connect this to the microphone output of your PC. G. DC Input Connect power input here. RETURN TO TOP OF THE PAGE Installing your Multimedia Pedestal 1. To INSTALL ● ● Slide the pedestal, aligning with the holes on the side. Then click the back hook into the corresponding hole on the bottom plate of your monitor.
6G3B11 Multimedia Base (option) 2. To UN-INSTALL ● ● Lift the back hook from the hole on the bottom plate of your monitor. Slide out the pedestal the opposite direction (from when you installed it). RETURN TO TOP OF THE PAGE Power adapter Installation Installing the adapter There are two (2) ways of installing the adapter A. T-connector B. Wall more connector Monitor T-connector Multimedia Base PC power cord.
6G3B11 Multimedia Base (option) RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_17/edoc/english/INSTALL_6/mm_pede/mm_inst.
The OSD Controls The OSD Controls Description of the On-Screen Display • The OSD Tree The OSD Controls : Brightness (HotKey) • Contrast (HotKey) • Language • Zoom • Adjust Horizontal • Adjust Vertical • Adjust Shape • Adjust Color • Reset to Factory Settings • Extra Controls • Close Main Controls BRIGHTNESS To adjust your screen's brightness, follow the steps below. Brightness is the overall intensity of the light coming from the screen. A 50% brightness is recommended.
The OSD Controls 2) Press the or button to adjust the contrast. 3) When the contrast is adjusted to the level desired, press to confirm and the CONTRAST window will disappear with the new adjustment saved. RETURN TO TOP OF THE PAGE LANGUAGE The ON SCREEN DISPLAY shows its settings in one of eight languages. The default is English, but you can select French, Spanish, German, Italian, Simplify-Chinese, Korea, or Brazilian Portuguese. 1) Press the button on the monitor.
The OSD Controls 3) Press the 4) Press the or button until the desired language is highlighted. button to confirm your selection and return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. RETURN TO TOP OF THE PAGE ZOOM ZOOM increases or decreases the size of the images on your screen. To adjust the ZOOM follow the steps below. 1) Press the button on the monitor. The MAIN CONTROLS window appears. file:///D|/EDFU/crt_17/edoc/english/OSD_2/osd_cont.
The OSD Controls 2) Press the 3) Press the 4) Press the 5) Press the button until ZOOM is highlighted. button. The ZOOM window appears. or button to adjust ZOOM. button to confirm your selection and Press again return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. RETURN TO TOP OF THE PAGE ADJUST HORIZONTAL ADJUST POSITION under ADJUST HORIZONTAL shifts the image on your screen either to the left or right. file:///D|/EDFU/crt_17/edoc/english/OSD_2/osd_cont.
The OSD Controls Use this feature if your image does not appear centered. ADJUST SIZE under ADJUST HORIZONTAL expands or controls the image on your screen, pushing it out toward the left and right sides or pulling it in toward the center. 1) Press the 2) Press the 3) Press the 4) Press the button on the monitor. The MAIN CONTROLS window appears. button until ADJUST HORIZONTAL is highlighted. button. The ADJUST HORIZONTAL window appears. POSITION should be highlighted.
The OSD Controls 5) When the position is adjusted, press the button to confirm. Press the to highlight SIZE, press to confirm. 6) To adjust the horizontal size, press the 7) When the size is adjusted, press the or button. button to confirm. Press again to return to MAIN CNTROLS sindow. CLOSE MAIN CONTROLS will be highlighted. RETURN TO TOP OF THE PAGE ADJUST VERTICAL ADJUST POSITION under ADJUST VERTICAL shifts the image on your screen either up or down.
The OSD Controls 3) Press the 4) Press the button. The ADJUST VERTICAL window appears. POSITION should be highlighted. or button to move the image up or down. 5) When the position is adjusted, press the window, or press the button. Press to highlight SIZE and again to return to MAIN CONTROLS to confirm. file:///D|/EDFU/crt_17/edoc/english/OSD_2/osd_cont.
The OSD Controls 6) To adjust the vertical size, press the 7) When the size is adjusted, press the or button. button to confirm. Press return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. RETURN TO TOP OF THE PAGE ADJUST SHAPE ADJUST SIDE CURVE ADJUST SIDE CURVE under ADJUST SHAPE allows you to adjust two of the five preset options. These two options are PINCUSHION and BALANCED pincushion. Note: use these features only when the picture is not square.
The OSD Controls 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the button. The SIDE CURVE window appears. PINCUSHION should be highlighted. Press to confirm. file:///D|/EDFU/crt_17/edoc/english/OSD_2/osd_cont.
The OSD Controls 5) To adjust the pincushion, press the or 6) When the pincushion is adjusted, press the 7) To adjust the balanced pincushion, press the button,press the to confirm. button to highlight BALANCED. Press or 8) When the balanced pincushion is adjusted, press the button.Press to confirm. to confirm. button to return to the ADJUST SHAPE window. BACK TO MAIN WINDOWS will be highlighted.
The OSD Controls ADJUST SIDE ANGLES under ADJUST SHAPE allows you to adjust two of the five preset options. These two options are TRAPEZOID and PARALLELOGRAM. Note: use these features only when the picture is not square. 1) Press the 2) Press the 3) Press the button on the monitor. The MAIN CONTROLS window appears. button until ADJUST SHAPE is highlighted. button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the button to highlight ADJUST SIDE ANGLES.
The OSD Controls to confirm. 6) To adjust the trapezoid, press the or 7) When the trapezoid is adjusted, press the PARALLELOGRAM, press button. button to confirm. Then to highlight to confirm. 8) To adjust the parallelogram, highlight parallelogram then to confirm. Press the or button to adjust.. 9) When the parallelogram is adjusted, press the button to confirm. Press again to return to the ADJUST SHAPE window. BACK TO MAIN WINDOWS will be highlighted.
The OSD Controls ROTATE IMAGE (Not available in all models) ROTATE IMAGE under ADJUST SHAPE allows you to adjust one of the five preset options. These two options are PINCUSHION and BALANCED pincushion. Note: use this feature only when the picture is not square. 1) Press the 2) Press the 3) Press the button on the monitor. The MAIN CONTROLS window appears. button until ADJUST SHAPE is highlighted. button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted.
The OSD Controls 5) Press the button. The ROTATE IMAGE window appears. ROTATE should be highlighted. 6) To adjust the rotation, press the or 7) When the rotation is adjusted, press the button. button to confirm. Press to return to the ADJUST SHAPE window. BACK TO MAIN CONTROLS should be highlighted. 8) Press the button to return to MAIN CONTROLS. RETURN TO TOP OF THE PAGE ADJUST COLOR Your monitor has three preset options you can choose from.
The OSD Controls 2) Press the button until ADJUST COLOR is highlighted. 3) Press the button. The ADJUST COLOR window appears. 4) Press the or button to highlight 9300K for GENERAL USE, 6500K for IMAGE MANAGEMENT, 5500K for PHOTO RETOUCH, or USER PRESET. 5) Once you have highlighted GENERAL USE, IMAGE MANAGEMENT, or PHOTO RETOUCH, press the button to confirm you selection. Press again to return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted.
The OSD Controls 6a) If USER PRESET is highlighted, press the Press or button to highlight RED. Next, press the to confirm. button to adjust the color red. 6b) When finished with RED, press to confirm.Next, press the or 6c) When finished GREEN, press to confirm. Next, press the to confirm. Press the button to highlight GREEN. press button to adjust the color green. to confirm.Then, press or button to highlight BLUE.Press button to adjust the color blue.
The OSD Controls 3) Press the button. The RESET TO FACTORY SETTINGS window appears. 4) Press the or button to select YES or NO. NO is the default. YES returns all settings to their original factory adjustments. 5) Press the button to confirm your selection and press again return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. RETURN TO TOP OF THE PAGE EXTRA CONTROLS DEGAUSS EXTRA CONTROLS is a set of three features, including DEGAUSS.
The OSD Controls build up that may distort the color on your screen. 1) Press the 2) Press the 3) Press the 4) Press the button on the monitor. The MAIN CONTROLS window appears. button until EXTRA CONTROLS is highlighted. button. The EXTRA CONTROLS window appears. MOIRE will be highlighted. button to highlight DEGAUSS. file:///D|/EDFU/crt_17/edoc/english/OSD_2/osd_cont.
The OSD Controls 5) To degauss your screen, press the button. Your screen will be degaussed, then the MAIN CONTROLS window will reappear. CLOSE MAIN CONTROLS will be highlighted. ADJUST MOIRE (Not available in all models) EXTRA CONTROLS is a set of three features, including ADJUST MOIRE. Moire is a fringe pattern arising from the interference between two superimposed line patterns. To adjust your moire, follow the steps below. Note: Use only if necessary.
The OSD Controls 3) Press the button. The EXTRA CONTROLS window appears. ADJUST MOIRE will be highlighted. 4) Press the button. The ADJUST MOIRE window appears. HORIZONTAL will be highlighted,press to confirm. file:///D|/EDFU/crt_17/edoc/english/OSD_2/osd_cont.
The OSD Controls 5) To adjust the horizontal moire, press the 6) When the horizontal moire is adjusted, press or button. to confirm. Press the button to highlight VERTICAL. 7) To adjust the vertical moire, press to confirm. Then press 8) When the vertical moire is adjusted, press the or button to adjust. to confirm. Press the EXTRA CONTROLS window. BACK TO MAIN CONTROLS will be highlighted. CLOSE MAIN CONTROLS file:///D|/EDFU/crt_17/edoc/english/OSD_2/osd_cont.
The OSD Controls RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_17/edoc/english/OSD_2/osd_cont.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
United States Guarantee LIMITED WARRANTY(Computer Monitor) Click here to access the Warranty Registration Card One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product as new is considered proof of purchase.
United States Guarantee customers only) or (402) 536-4171. Before Requesting Service... Please check your owner's manual before requesting service. Adjustments of the controls discussed there may save you a service call. TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS... Contact the Philips Customer Care Center phone number listed below for product assistance and procedures for servicing: Philips Customer Care Center (877) 835-1838 or (402) 536-4171 (In U.S.A., Puerto Rico and U.S.
United States Guarantee performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty. This one-year service warranty entitles you to a swap model on-site within 48 hours of your call being received within the first year of purchase.
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Czech Republic • Dubai • Egypt • Hong Kong • Hungary • India • Indonesia • Japan • Korea • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Russia • Singapore • South Africa • Taiwan • Thailand • Turkey • Uruguay • Venezuela Eastern Europe CZECH REPUBLIC Philips Service V Mezihorí 2180 00 Prague Phone: (02)-683
Consumer Information Centers ANTILLES Philips Antillana N.V.Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (09)-4612799 Fax : (09)-4612772 ARGENTINA Vedia 3892 Capital Federal CP:1430 Buenos Aires Phone: (011)-4544 2047 Fax: (011)-4544 2928 BRASIL Philips da Amazonia Ind. Elet.Ltda. Av.Luis Carlos Berrini, 1400-Sao Paulo-SP Phone: 0800-7010-203 CHILE Philips Chilena S.A. Avenida Santa Maria 0760 P.O.
Consumer Information Centers PARAGUAY Philips del Paraguay S.A. Avenida Artigas 1513 Casilla de Correos 605 Asuncion Phone: (021)-211666 Fax : (021)-213007 PERU Philips Peruana S.A. Customer Desk Comandante Espinar 719 Casilla 1841 Limab18 Phone: (01)-2136200 Fax : (01)-2136276 URUGUAY Ind.Philips del Uruguay S.A. Lius Alberto de Herrera 1248-P:10 Customer Help Desk 11300 Montevideo Phone: (02)-6281111 Fax : (02)-6287777 VENEZUELA Industrias Venezolanas Philips S.A.
Consumer Information Centers NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (Toll Free) Fax:0800 288 588 Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA SHANHAI No. 1102 wuding road, jing an district, 200040 Shanghai, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 NANJING No.
Consumer Information Centers 110003 Shenyang P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 XIAN No. 6-9 yan ta road south part, 710061 Xian, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 GUANGZHOU No. 15-17 long kou dong road, tian he district, 510070 Guangzhou, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 SHENZHEN Room 603, electronic BLD, No. 30 Shen nan zhong road, 518031 Shenzhen, P.R.
Consumer Information Centers HONG KONG Philips Hong Kong Limited Consumer Information Centre 16/F Hopewell Centre 17 Kennedy Road, WANCHAI Phone: 2619-9663 Fax: 2481 5847 INDIA BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr.
Consumer Information Centers JAPAN Philips Consumer Electronics 1-11-9,Ebisuminami Shibuya-Ku Tokyo 150 Phone: (03)-3719-2235 Fax : (03)-3715-9992 KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone: 080 600 6600 (Toll Free) Fax:(02)709 1245 MALAYSIA Philips Malaysia Sdn. Berhad Service Dept. No.51,sect.13 Jalan University. 46200 Petaling Jaya, Selagor. P.O.box 12163 50768 Kuala Lumpur.
Consumer Information Centers SINGAPORE Philips Singapore Private Ltd. Consumer Service Dept. Lorong 1,Toa Payoh., P.O. box 340 Singapore 1231 Phone:6882 3999 Fax:6250 8037 TAIWAN Philips Taiwan Ltd. Consumer Information Centre 26F, 66, Chung-Hsiao W. Road, Sec. 1 Taipei, Taiwan Phone: (02)-2382-4567 ,0800-231-099 Fax:(02)2382-3027 THAILAND Philips Electronics (Thailand) Ltd.
Consumer Information Centers DUBAI Philips Middle East B.V. Consumer Information Centre P.O.Box 7785 DUBAI Phone: (04)-3353666 Fax : (04)-3353999 EGYPT Philips Egypt Consumer Information Centre 10, Abdel Rahman El Rafei Mohandessin - Cairo, P.O.Box 242 DOKKI Phone: (02)-3313993 Fax : (02)-3492142 file:///D|/EDFU/crt_17/edoc/english/WARRANTY/warcic.
PHILIPS Warranty Card 8/16/02 12:38 PM Page 1 It Takes Only A Moment To PROTECT YOUR INVESTMENT. Congratulations on investing in a Philips product. It’s an important and intelligent decision that’s sure to reward you for many years to come. To ensure you’ll get all of the privileges and protection that come with your purchase, please complete your Warranty Registration Card within the next ten days. SIMPLY MAIL THE CARD BELOW TO RECEIVE ALL OF THESE BENEFITS TO WHICH YOU’RE ENTITLED.
PHILIPS Warranty Card 8/16/02 12:38 PM Page 2 !1375415338! PO BOX 1533 DEPOSIT NY 13754-1533 Please Open Promptly! TIME-DATED MATERIAL a PLEASE APPLY FIRST CLASS STAMP IMPORTANT Warranty Registration Card RETURN THE ATTACHED CARD WITHIN TEN DAYS TO ENSURE YOUR: ✓ Warranty Verification ✓ Owner Confirmation ✓ Model Registration See Inside For Valuable Benefits!
F1rst Choice Contact Information F1rst Choice Contact Information Telephone numbers: Austria 01 546 575 603 Belgium 02 275 0701 Cyprus 800 92256 Denmark 35 25 87 61 France 03 8717 0033 Germany 0696 698 4712 Greece 00800 3122 1223 Finland 09 2290 1908 Ireland 01 601 1161 Italy 02 48 27 11 53 Luxembourg 408 443 5501 The Netherlands 053 482 9800 Norway 22 70 82 50 Portugal 0800 831 363 Sweden 08 632 0016 Switzerland 02 23 10 21 16 Spain 09 17 45 62 46 United Kingdom 0207 949
