Philips 150S3F/150S3H Electronic User's Manual file:///D|/03771/english/150s3fh/index.
Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Installation Locations • FAQs • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.
Safety & Troubleshooting Installation Locations ● Avoid Heat and Extreme Cold Do not store or use the LCD monitor in locations exposed to heat, direct sunlight, or extreme cold. Avoid moving the LCD monitor between locations with large temperature differences. Choose a site falling within the following temperature and humidity ranges. ❍ Temperature: 5-40°C 41-104°F ● Humidity: 20-80% RH Do not subject the LCD monitor to severe vibration or high impact conditions.
About This Electronic User's Manual About This Manual About This Guide • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other pertinent information. Its contents are identical to the information in our printed version.
About This Electronic User's Manual CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority. RETURN TO TOP OF THE PAGE ©2002 Koninklijke Philips Electronics N.V.
Product Information Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Physical Function Product Features 150S3F / 150S3H Embedded Power Supply ● 15-inch color LCD monitor with excellent display performance ● Ultra slim frame design Standard VGA analog input Embedded universal AC power supply AUTO adjustment optimizes picture quality User installabl
Product Information VIDEO • Video dot rate 80 MHz • Input impedance - Video 75 ohm - Sync 5K6 ohm • Input signal levels 700m Vpp • Sync input signal Separate sync Composite sync Sync on Green • Sync polarities Positive and negative • Input Frequency XGA Hsync SVGA Hsync VGA Hsync • Video interface Analog (D-Sub) 48- 61 kHz, Vsync 60 - 76 Hz (N.I.) 35- 50 kHz, Vsync 56 - 75 Hz (N.I.) 31- 38 kHz, Vsync 60 - 76 Hz (N.I.) OPTICAL CHARACTERISTICS • Contrast ratio 350 (typ.
Product Information 14 user definable modes 14 factory preset modes: H. freq (kHz) Resolution V. freq (Hz) 31.469 640*350 70.086 31.469 720*400 70.087 31.469 640*480 59.940 35.000 640*480 67.000 37.861 640*480 72.809 37.500 640*480 75.000 35.156 800*600 56.250 37.879 800*600 60.317 48.077 800*600 72.188 46.875 800*600 75.000 49.700 832*624 75.000 48.363 1024*768 60.004 56.476 1024*768 70.069 60.023 1024*768 75.
Product Information Stand-by Blanked No Yes < 2W Amber Suspend Blanked Yes No < 2W Amber OFF Blanked No No < 2W Amber This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimension (WxHxD) * 343 x 310 x 170 mm (incl. Pedestal) • Weight * 3.
Product Information Pin Assignment No. Pin Assignment No. 1 2 Red video input Green video input 9 10 DDC +5V Logic ground Identical output - connected to pin 10 3 Blue video input 11 4 Identical output - connected to pin 10 12 Serial data line (SDA) 5 6 Cable detect Red video ground 13 14 H. Sync / H+V V.
Product Information Tilt RETURN TO TOP OF THE PAGE file:///D|/03771/english/150s3fh/product/product.
Installing your LCD Monitor Installing your LCD Monitor Your LCD Monitor : Front View Product Description • Connecting to Your PC • Tthe Base • Getting Started • Optimizing Performance • Accessories (optional) Front View Product Description UP and DOWN buttons are used when adjusting the OSD of your monitor LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. BRIGHTNESS hotkey.
Installing your LCD Monitor RETURN TO TOP OF THE PAGE Optimizing Performance ● For best performance, ensure that your display settings are set at 1024x768@60Hz (for14"/15") or 1280x1024, 60Hz (for17"/18"). Note: You can check the current display settings by pressing the "OK" button once. Go into the Product Information. The current display mode is shown on the item called RESOLUTION.
On-Screen Display On-Screen Display Description of the On-Screen Display • The OSD Tree Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips LCD monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display file:///D|/03771/english/150s3fh/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/03771/english/150s3fh/osd/osddesc.
Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • Peru • Uruguay • Vene
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ C Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source. Most Philips monitors offer the possibility of setting the color temperature to any desired value. RETURN TO TOP OF THE PAGE D D-SUB USB Your monitor comes with a D-Sub cable.
Glossary E Energy Star Computers Programme An energy conservation programme launched by the US Environmental Protection Agency (EPA) with the primary aim of promoting the manufacture and marketing of energy-efficient office automation equipment. Companies joining this programme must be willing to commit themselves to manufacturing one or more products capable of going into a low -power state (< 30 W) either after a period of inactivity or after a predetermined time selected by the user.
Glossary A Universal Serial Bus device that provides additional connections to the Universal Serial Bus. Hubs are a key element in the plug-and-play architecture of USB. The Figure shows a typical hub. Hubs serve to simplify USB connectivity from the user's perspective and provide robustness at low cost and complexity. Hubs are wiring concentrators and enable the multiple attachment characteristics of USB. Attachment points are referred to as ports.
Glossary Upstream The direction of data flow towards the host. An upstream port is the port on a device electrically closest to the host that generates upstream data traffic from the hub. Upstream ports receive downstream data traffic. RETURN TO TOP OF THE PAGE V Vertical refresh rate Expressed in Hz, it is the number of frames (complete pictures) written to the screen every second. RETURN TO TOP OF THE PAGE file:///D|/03771/english/150s3fh/glossary/glossary.
Download and Print Download and Print Installing your LCD monitor driver • Download and Printing Instructions • Installing FPadjust Program Installing Your LCD monitor driver System requirements: ● ● PC running Windows 95, Windows 98, Windows 2000 , Windows Me, Windows XP or later Find your driver ".inf/.icm/.cat" at : /PC/drivers/ Read the "Driver_install02.txt" file before installing. This page provides an option to read the manual in .pdf format.
Download and Print Download 150B3E.pdf Download 150B3M.pdf Download 150B3Q.pdf Download 150B3T.pdf Download 150B3V.pdf Download 150B3Y.pdf Download 150S3F.pdf Download 150S3H.pdf Download 150X3M.pdf Download 150V3F.pdf 2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to Disk'. 3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or 'source', choose 'source'). Printing instructions: To print the manual: 1.
Download and Print Installing FPadjust Program The FP Adjust program generates alignment patterns which will help you adjust monitor settings such as CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL POSITION, PHASE and CLOCK. System requirements: ● PC running Windows 95, Windows 98, Windows 2000, Winodws Me, Windows XP or later To install FPadjust Program: ● ● Click on the link or icon to install FPadjustment Program. or Click-and-hold your mouse over the icon.
FAQs (Frequently Asked Questions) FAQs (Frequently Asked Questions) Safety and Troubleshooting • General FAQ • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology, and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information General FAQs Q: When I install my monitor how do I do if the screen shows "Cannot display this video mode"? A: Recommended video mode for Philips 14"/15": 1024x768 @60Hz for Philips 17"/18" 1280x1024@60H
FAQs (Frequently Asked Questions) Q: What does "refresh rate" mean to me in an LCD monitor? A: For LCD monitors, the refresh rate is much less relevant. LCD monitors display a stable, flicker-free image at 60Hz. There is no visible differences between 85Hz and 60Hz. Q: What are the .inf and .icm files on the setup disk & CD-ROM? How do I install the drivers (.inf and .icm)? A: These are the driver files for your monitor. Follow the instructions in your user manual to install the drivers.
FAQs (Frequently Asked Questions) Q: Does Refresh Rate mean to LCD? A: Unlike CRT display technology in which the speed the electron beam is swept from the top to the bottom of the screen determines flicker, an active matrix display uses an active element (TFT) to control each individual pixel and thus refresh rate is not really applicable to LCD technology.
FAQs (Frequently Asked Questions) Q: When I install my monitor, how do I get the best performance for the monitor? A: 1. For best performance, make sure your display settings are set at 1024x768@60Hz for 14"/15", 1280x1024@60Hz for 17"/18". Note: You can check the current display settings by pressing the OSD OK button once. The current display mode is shown in product information in OSD main controls. 2.
FAQs (Frequently Asked Questions) adjustment of complicated IRQ settings -- for add-on peripherals. USB does away with "port gridlock." Without USB, PCs are normally limited to one printer, two Com port devices (usually a mouse and modem), one Enhanced Parallel Port add-on (scanner or video camera, for example), and a joystick. More and more peripherals for multimedia computers come on the market every day. With USB, up to 127 devices can run simultaneously on one computer. USB permits "hot plug-in.
FAQs (Frequently Asked Questions) Q: What differentiates passive matrix LCDs from active matrix LCDs? A: An LCD is made with either a passive matrix or an active matrix display grid. An active matrix has a transistor located at each pixel intersection, requiring less current to control the luminance of a pixel.
FAQs (Frequently Asked Questions) Q: What kind of wide-angle technology is available? How does it work? A: The TFT LCD panel is an element controls/displays inlet of a backlight using the dual-refraction of liquid crystal. Using the property that the projection of inlet light refracts toward the major axis of the liquid element, it controls the direction of inlet light and displays it.
FAQs (Frequently Asked Questions) A: Yes. Philips LCD monitors conform to the guidelines of MPR-II and TCO 95-99 standards for the control of radiation, electromagnetic waves, energy reduction, electrical safety in the work environment, and recyclability. The specification page provides detailed safety standards data. More information is provided in the Regulatory Information chapter. RETURN TO TOP OF THE PAGE file:///D|/03771/english/150s3fh/safety/saf_faq.
Troubleshooting Troubleshooting Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • Regulatory Information • Other Related Information This page presents problems that can be corrected by the user. If the problem still exists after these possible solutions, contact your nearest Philips dealer.
Troubleshooting ● Push the Auto button. Adjust the image position using the Horizontal Position &/or Vertical Position in OSD Main Controls. Display position is incorrect ● Image vibrates on the screen ● Check that the signal cable is properly connected to the graphics board or PC. ● Push the Auto button. Eliminate the vertical bars using the Clock Adjustment of VIDEO NOISE in OSD Main Controls.
Troubleshooting file:///D|/03771/english/150s3fh/safety/saf_troub.
Regulatory Information Regulatory Information TCO '95 Information • TCO '95 Environmental Requirements • TCO '99 Information • TCO '99 Environmental Requirements • CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
Regulatory Information TCO Development Unit SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'95 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.
Regulatory Information TCO '99 Information (For 150P3A, 150P3E, 150B3B, 150B3E, 150B3M, 150S3F) Congratulations! You have just purchased a TCO '99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Regulatory Information the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes.
Regulatory Information Energy Star Declaration PHILIPS 150S3F 150S3H This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94. Time settings are adjusted from the system unit by software.
Regulatory Information RETURN TO TOP OF THE PAGE Commission Federale de la Communication (FCC Declaration) Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une installation résidentielle.
Regulatory Information Class B ITE RETURN TO TOP OF THE PAGE MIC Notice (South Korea Only) Class B Device Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket).
Regulatory Information RETURN TO TOP OF THE PAGE North Europe Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. file:///D|/03771/english/150s3fh/safety/regs/regulat.
Regulatory Information Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ. RETURN TO TOP OF THE PAGE BSMI Notice (Taiwan Only) RETURN TO TOP OF THE PAGE Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften.
Regulatory Information Information for UK only WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
Other Related Information Other Related Information Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information for Users in the U. S. • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
Philips Pixel Defect Policy Philips Pixel Defect Policy Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control.
Philips Pixel Defect Policy One lit red, green or blue subpixel Two adjacent lit subpixels: Three adjacent lit subpixels (one - Red + Blue = Purple white pixel) - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Black Dot Defects Black dot defects appear as pixels or subpixels that are always dark or "off".
Philips Pixel Defect Policy Bright dot defects within 20 mm circle 0 0 3 or fewer Total bright dot defects of all types 0 0 8 or fewer BLACK DOT DEFECTS ACCEPTABLE LEVEL 150P3 150B3 150S3 1 dark subpixel 4 or fewer 4 or fewer 8 or fewer 2 adjacent dark subpixels 1 or fewer 1 or fewer 3 or fewer 3 adjacent dark subpixels 0 0 1 or fewer Distance between two black dot defects* 15 mm or more 15 mm or more 15 mm or more Black dot defects within 20 mm circle* 3 or fewer 3 or fewer
Connecting to Your PC Connecting to Your PC Your LCD Monitor : Front View Product Description • Accessory Pack • Connecting to Your PC • The Base • Getting Started • Optimizing Performance • Accessories (optional) Accessory Pack Unpack all the parts.
Connecting to Your PC 6) E-DFU package with Quick Setup Guide, Using Your Monitor Manual, and CD-ROM. 7) Pivot CD-ROM (optional) RETURN TO TOP OF THE PAGE Connecting to Your PC 1) Plug the power cord into monitor firmly. file:///D|/03771/english/150s3fh/install/connect.
Connecting to Your PC Note: If you use an Apple Macintosh, you need to connect the special Mac adapter to one end of the monitor signal cable 2) Connect to PC (a) Turn off your computer and unplug its power cable. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Plug the power cord of your computer and your monitor into a nearby outlet. (d) Turn on your computer and monitor. If the monitor displays an image, installation is complete.
The base The Base Your LCD Monitor : Front View Product Description • Accessory Pack • Connecting to Your PC • Getting Started • Optimizing Performance • Accessories (optional) Unfold and Fold the Base : Unfold the base • Fold the base Remove the Base : Remove the base Unfold and Fold the Base Unfold the Base 1) Put monitor face down on the safe surface 2) Pull up the base file:///D|/03771/english/150s3fh/install/base.
The base Fold the Base 1) Put monitor face down on the safe surface 2) Push down the button and fold the base RETURN TO TOP OF THE PAGE Remove the Base Condition: ● for VESA standard mounting applications ● for optional bases replacement file:///D|/03771/english/150s3fh/install/base.
The base 1) Remove the four screws and then remove the stand from the LCD monitor. 2) Remove the back cover file:///D|/03771/english/150s3fh/install/base.
The base Note: This monitor accepts a 100mmx100mm VESA-Compliant mounting interface. RETURN TO TOP OF THE PAGE file:///D|/03771/english/150s3fh/install/base.
Getting Started Getting Started Your LCD Monitor : Front View Product Description • Connecting to Your PC • The Base • Getting Started • Optimizing Performance • Accessories (optional) Getting Started Use the information file ( .inf) for Windows 95/98/2000/Me/XP or later Philips' monitors built in VESA DDC2B feature to support Plug & Play requirements for Windows 95/98/2000/Me/XP.
Getting Started 1. 2. 3. 4. 5. 6. 7. Start Windows Me Click the 'Start' button, point to 'Settings', and then click 'Control Panel'. Double Click the 'Display' Icon. Choose the 'Settings' tab then click 'Advanced...'. Choose 'Monitor' button, then click 'Change...' button. Choose "Specify the location of the driver(Advanced)" and click the 'Next' button. Choose "Display a list of all the drivers in a specific location, so you can select the driver you want." then click 'Next' and then click 'Have Disk...
Getting Started 'Next' button. 9. Choose the ' Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button. 10. Click the 'Have disk...' button then click the 'Browse...' button. Then choose the appropriate drive F: (CD-ROM Drive). 11. Click the 'Open' button, then click the 'OK' button. 12. Choose your monitor model and click the 'Next' button.
Accessories (optional) Accessories (optional) Your LCD Monitor : Front View Product Description • Connecting to Your PC • The Base • Getting Started • Optimizing Performance Accessories (optional): Protective Cover • Ergo Base • Multimedia Base• USB Hub Accessories (optional) These accessories may not be available in NAFTA.
Accessories (optional) Multimedia Base: (VG3P40) 2W each, 48W PMPO, stereo front firing & portrait display, tilt & swivel. Color: Light gray RETURN TO TOP OF THE PAGE Protective Cover Protect the LCD screen of your Philips LCD monitor 1) Remove the screw from the rear of monitor 2) Unclick at the indicated points to open the bezel file:///D|/03771/english/150s3fh/install/access.
Accessories (optional) 3) Pull forward to release the bezel completely 4) Peel off the film from both sides of the protective cover 5) Mount the protective cover and press each corner to attach it securely 6) Fix the screw onto the rear of monitor RETURN TO TOP OF THE PAGE file:///D|/03771/english/150s3fh/install/access.
Accessories (optional) Ergo Base Tilt Swivel file:///D|/03771/english/150s3fh/install/access.
Accessories (optional) Height adjustment Portrait display 1) Tilt the monitor body at an angle 2) Rotate the monitor body 90 degrees counter clockwise. file:///D|/03771/english/150s3fh/install/access.
Accessories (optional) RETURN TO TOP OF THE PAGE Multimedia Base Tilt file:///D|/03771/english/150s3fh/install/access.
Accessories (optional) Swivel Height adjustment Portrait display Turn monitor from landscape view to portrait view 1) Tilt the monitor body at an angle file:///D|/03771/english/150s3fh/install/access.
Accessories (optional) 2) Rotate the monitor body 90 degrees counter clockwise. RETURN TO TOP OF THE PAGE file:///D|/03771/english/150s3fh/install/access.
USB Hub USB Hub USB Hub: About this product • Installation About this product Package Contents Each package should include the following parts: ● 1 USB 4-port Clip-On HUB ● 1 USB cable ● 1 Switching AC Adapter ● 1 Owner's manual Features ● ● ● ● ● ● ● Fulfill the USB-IF Specification Revision 1.1 and HID Class Definition Rev. 1.0 Support up to 127 USB devices simultaneously. Stand-alone or clip-on to Philips monitor range. Support for realtime dynamic insertion and removal.
USB Hub 3) Down Stream Ports : 4 USB A-type receptacles on both sides connect to USB devices. 4) Up Stream Port : 1 USB B-type receptacle to connect to the PC. 5) Power Socket : For the supplied AC Adapter jack to connect to. RETURN TO TOP OF THE PAGE Installation This Hub consists of two parts: functional and aesthetic. The aesthetic elements is a removable cover. A slot for this Hub to install in can be found in the back of the LCD monitor base.
USB Hub Power connection ● It is recommended that the AC adapter be plugged into the electrical outlet before the hub. ● It is recommended that the AC adapter is used at all time for high-speed devices and multiple devices may cause a power shortage in the hub. ● It is recommended that the AC adapter be used whenever multiple hubs in a stacking configuration. ● Do not remove the Ac adapter while the hubs is working.
USB Hub ● ● hardware device, searching software for installation" will appear. Your computer will then start up the Device Driver Wizard, and install the hub. Once the setup has finished the installation, you can connect USB devices to it. RETURN TO TOP OF THE PAGE file:///D|/03771/english/150s3fh/install/usb.
F1rst Choice Warranty Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
United States Guarantee LIMITED WARRANTY (Computer Monitor) One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product as new is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product.
United States Guarantee Where CAN I GET MORE INFORMATION and HOW CAN I OBTAIN SERVICE? For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A. customers only) or (903) 242-4804. Before Requesting Service... Please check your owner's manual before requesting service. Adjustments of the controls discussed there may save you a service call. TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...
United States Guarantee All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty. This one-year service warranty entitles you to a swap model on-site within 48 hours of your call being received within the first year of purchase.
F1rst Choice Contact Information F1rst Choice Contact Information Telephone numbers: Austria 01 546 575 603 Luxembourg 408 443 5501 Belgium 02 275 0701 Netherlands 053 482 9800 Cyprus (Greek) 800 92256 Norway 22 70 82 50 Denmark 35 25 87 61 Portugal 0800 831 363 France 03 8717 0033 Sweden 08 632 0016 Germany 0696 698 4712 Switzerland 02 23 10 21 16 Greece 00800 3122 1223 Spain 09 17 45 62 46 Finland 09 2290 1908 United Kingdom 0207 949 0069 Ireland 01 601 1161 U.S.A.
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia• Bangladesh • Brasil • Canada • Chile• China • Colombia • Czech Republic • Dubai • Egypt • Hong Kong • Hungary • India • Indonesia • Korea • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Russia • Singapore • South Africa • Taiwan • Thailand • Turkey • Uruguay • Venezuela Eastern Europe CZECH REPUBLIC Philips Service V Mezihorí 2180 00 Prague Phone: (02)-6831581 Fax :
Consumer Information Centers ANTILLES Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (09)-4612799 Fax : (09)-4612772 ARGENTINA Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (01)-544 2047 BRASIL Philips da Amazônia Ind. Elet. Ltda. Centro de Informações ao Consumidor R. Alexandre Dumas, 2100-5. andar Phone: 0800-701-203 Fax : (0xx11) 3141-1580 CHILE Philips Chilena S.A.
Consumer Information Centers PARAGUAY Philips del Paraguay S.A. Avenida Artigas 1519 Casilla de Correos 605 Asuncion Phone: (021)-211666 Fax : (021)-213007 PERU Philips Peruana S.A. Customer Desk Comandante Espinar 719 Casilla 1841 Limab18 Phone: (01)-2412890 Fax : (01)-2412913 URUGUAY Ind.Philips del Uruguay S.A. Avenida Uruguay 1287 Customer Help Desk 11100 Montevideo Phone: (02)-923392 Fax : (02)-920752 VENEZUELA Industrias Venezolanas Philips S.A.
Consumer Information Centers NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (toll free) Fax : 0800 288 588 (toll free) Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA BEIJING Beijing Authorized Service Centre. Consumer Information Centre Building 6, West Street Chong Wen Men, Beijing, Jin Bang Co. Led.
Consumer Information Centers HONG KONG Philips Hong Kong Limited Consumer Information Centre 16/F Hopewell Centre 17 Kennedy Road, WANCHAI Phone: 2619 9663 Fax : 2481 5847 INDIA Phone: 91-20-712 2048 ext: 2765 Fax: 91-20-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr.
Consumer Information Centers KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone:080-600-6600 (Local toll free) Fax : (02)-709-1245 MALAYSIA Philips Malaysia Sdn. Berhad Service Dept. No.51,sect.13 Jalan University. 46200 Petaling Jaya, Selagor. P.O.box 12163 50768 Kuala Lumpur. Phone: (03)-7950 5501/02 Fax : (03)-7954 8504 PAKISTAN KARACHI Philips Electrical Ind. of Pakistan Consumer Information Centre F-54, S.I.T.E, P.O.
Consumer Information Centers SINGAPORE Philips Singapore Private Ltd. Consumer Service Dept. Lorong 1,Toa Payoh., P.O. box 340 Singapore 1231 Phone: 6882 3999 Fax : 6250 8037 TAIWAN Philips Taiwan Ltd. Consumer Information Centre Nr 96 Section 1, Chien-Kuo N.Road TAIPEI Phone: (02)-2382-4567 or 0800-231-099 Fax : (02)-2382-3027 THAILAND Philips Electronics (Thailand) Ltd.
Consumer Information Centers DUBAI Philips Middle East B.V. Consumer Information Centre P.O.Box 7785 DUBAI Phone: (04)-335 3666 Fax : (04)-335 3999 EGYPT Philips Egypt Consumer Information Centre 10, Abdel Rahman El Rafei Mohandessin - Cairo, P.O.Box 242 DOKKI Phone: (02)-3313993 Fax : (02)-3492142 file:///D|/03771/english/warranty_1/warcic.
