e-Manual Philips LCD Monitor Electronic User’s Manual file:///D|/My%20documents/dfu/W7/english/170b5/index.
Safety and Troubleshooting Information • Safety Precautions and Maintenance • Installation Locations • FAQs Safety and Troubleshooting Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.
Safety and Troubleshooting Information ● ● ● ● ● ● Avoid exposure to heat and extreme cold. Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or extreme cold. Avoid moving the LCD monitor between locations with large temperature differences. Choose a site that falls within the following temperature and humidity ranges. ❍ Temperature: 5-40°C 41-104°F ❍ Humidity: 20-80% RH Do not subject the LCD monitor to severe vibration or high impact conditions.
About This Manual • About This Guide • Notational Descriptions About This Manual About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other important information. Its contents are identical to the information in our printed version.
About This Manual NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may not be accompanied by an icon.
Product Information • SmartManage • Product Product Information Features • Technical Specifications • Resolution & Product Features Preset Modes • Philips Pixel 170B5 Defect Policy • Automatic ● Outstanding front of screen performance Power Saving ❍ Zero Bright DotTM ~ Zero tolerance for LCD bright dot defects - guaranteed • Physical ❍ Fast response time ~ Get the job done quicker with fast response time Specification ❍ SXGA, 1280 x 1024 resolution ~ Accurate color displaying more than 1.
Product Information • Display Colors 16M colors SCANNING Vertical refresh rate 56 Hz-76 Hz Horizontal Frequency 30k Hz-82 kHz VIDEO • Video dot rate 135 MHz • Input impedance - Video - Sync 75 ohm 2.2K ohm • Input signal levels 0.
Product Information • Response time <16 ms (typ.) sRGB sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.) Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen.
Product Information H. freq (kHz) Resolution V. freq (Hz) 31.5 640*350 70 31.5 720*400 70 31.5 640*480 60 35.0 640*480 67 37.5 640*480 75 35.2 800*600 56 37.9 800*600 60 46.9 800*600 75 49.7 832*624 75 48.4 1024*768 60 60.0 1024*768 75 69.0 1152*870 75 71.8 1152*900 76 63.9 1280*1024 60 80.
Product Information This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimension (WxHxD) * 375 x 376 x 210 mm (in lowest position) • Weight 6 kg • Tilt / Swivel -5° ~ 25° / + - 125° • Height adjustment rang 70 mm • Power supply 100 — 240 VAC, 50/60 Hz • Power consumption 40 W* (typ.
Product Information T.M.D.S. Data1/3 Shield T.M.D.S. Data0/5 Shield 3 T.M.D.S. Data2/4 Shield 11 4 No connect 12 No connect 20 No connect 5 No connect 13 No connect 21 No connect 6 DDC Clock 14 +5V Power 22 7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock+ 8 No connect 16 Hot Plug Detect 24 T.M.D.S. Clock- 19 T.M.D.S. Clock Shield 2. The 15-pin D-sub connector (male) of the signal cable: Pin Assignment No. Pin Assignment No.
Product Information RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components. Front View Product Description RETURN TO TOP OF THE PAGE Physical Function 1) Tilt file:///D|/My%20documents/dfu/W7/english/170b5/product/product.
Product Information 2) Swivel 3) Height adjustment RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/170b5/product/product.
Installing Your LCD Monitor Installing Your LCD Monitor Front View • Produt Description Connecting • to Your PC Front View Product Description • The Base Getting Started Optimizing • Performance • UP and DOWN buttons are used when adjusting the OSD of your monitor. LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. BRIGHTNESS hotkey. When the UP and DOWN arrow buttons are pressed, the adjustment controls for the BRIGHTNESS will show up.
Installing Your LCD Monitor Rear View 1 Kensington anti-thief lock 2 VGA input 3 DVI-D input 4 PC audio input 5 Earphone jack 6 AC power input RETURN TO TOP OF THE PAGE Optimizing Performance ● For best performance, ensure that your display settings are set at 1280x1024, 60Hz. Note: You can check the current display settings by pressing the 'OK' button once. Go into the Product Information. The current display mode is shown on the item called RESOLUTION.
Installing Your LCD Monitor provided to guide you through the installtion process. Click on the link to know more about this program. More about FP_setup04.exe RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/170b5/install/install.
On-Screen Display On-Screen Display • Description of the OnScreen Display Description of the On Screen Display The OSD • Tree What is the On-Screen Display? This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides userfriendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display Digital signal input: file:///D|/My%20documents/dfu/W7/english/170b5/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/170b5/osd/osddesc.
Customer Care & Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Slovakia • Slovenia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • P
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ C Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source. Most Philips monitors offer the possibility of setting the color temperature to any desired value. RETURN TO TOP OF THE PAGE D D-SUB Your monitor comes with a D-Sub cable.
Glossary The DVI interface enables: 1. 2. 3. 4. Reduce signal loss and video noise in signal due to less signal conversion. Independent from display technology, and can be used on LCD, Plasma, LCOS, etc. Plug and play through hot plug detection, EDID and DDC2B. Digital and Analog support in a single connector (DVI-I only).
Glossary V Vertical refresh rate Expressed in Hz, it is the number of frames (complete pictures) written to the screen every second. RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/170b5/glossary/glossary.
Download and Print Download and Print • Installing your LCD monitor driver Installing Your LCD monitor driver • Download and System requirements: Printing Instructions ● PC running Windows 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP or later Installing ● Find your driver ".inf/.icm/.cat" at : /PC/drivers/ • FPadjust Program Read the "Driver_install02.txt" file before installing. This page provides an option to read the manual in .pdf format.
Download and Print Printing instructions: To print the manual: 1. With the manual file open, follow your printer's instructions and print the pages you need. RETURN TO TOP OF THE PAGE Installing FPadjust Program The FP Adjust program generates alignment patterns which will help you adjust monitor settings such as CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL POSITION, PHASE and CLOCK.
Download and Print RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/download/download.
FAQs (Frequently Asked Questions) • Safety and Troubleshooting • General FAQs • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information FAQs (Frequently Asked Questions) General FAQs Q: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? A: Recommended video mode for Philips 17": 1280x1024 @60Hz. 1.
FAQs (Frequently Asked Questions) Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and . icm)? A: These are the driver files for your monitor. Follow the instructions in your user manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .icm files) or a driver disk when you first install your monitor. Follow the instructions to insert the driver disk (either floppy or CD-ROM) included in this package. Monitor drivers (.inf and .
FAQs (Frequently Asked Questions) A: Unlike CRT display technology, in which the speed of the electron beam is swept from the top to the bottom of the screen determines flicker, an active matrix display uses an active element (TFT) to control each individual pixel and the refresh rate is therefore not really applicable to LCD technology.
FAQs (Frequently Asked Questions) A: 1. For best performance, make sure your display settings are set at 1280x1024@60Hz for 17". Note: You can check the current display settings by pressing the OSD OK button once. The current display mode is shown in product information in OSD main controls. 2. To install the Flat Panel Adjust (FPadjust) program located on the monitor setup CD-ROM, open the CD-ROM and double-click the FP_setup04.exe icon.
FAQs (Frequently Asked Questions) peripherals for multimedia computers come on the market every day. With USB, up to 127 devices can run simultaneously on one computer. USB permits "hot plug-in." No need to shut down, plug in, reboot and run set up to install peripherals. No need to go through the reverse process to unplug a device. Bottom line: USB transforms today's "Plug-and-Pray" into true Plug-and-Play! Q: What is a USB hub ? A: A USB hub provides additional connections to the Universal Serial Bus.
FAQs (Frequently Asked Questions) direction. Q: What differentiates passive matrix LCDs from active matrix LCDs? A: An LCD is made with either a passive matrix or an active matrix display grid. An active matrix has a transistor located at each pixel intersection, requiring less current to control the luminance of a pixel.
FAQs (Frequently Asked Questions) 65MHz dot clock, one of the standards for XGA displays. Since the vertical/horizontal frequency for this dot clock is 60Hz/48kHz, the optimum frequency for this monitor is 60Hz. Q: What kind of wide-angle technology is available? How does it work? A: The TFT LCD panel is an element that controls/displays the inlet of a backlight using the dual-refraction of a liquid crystal.
FAQs (Frequently Asked Questions) S. National Electrical Code and UL Standards. Q: Does the LCD monitor conform to general safety standards? A: Yes. Philips LCD monitors conform to the guidelines of MPR-II and TCO 99/03 standards for the control of radiation, electromagnetic waves, energy reduction, electrical safety in the work environment and recyclability. The specification page provides detailed data on safety standards. More information is provided in the Regulatory Information section.
Troubleshooting Troubleshooting • Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • Regulatory Information • Other Related Information This page deals with problems that can be corrected by the user. If the problem still persists after you have tried these solutions, contact your nearest Philips dealer.
Troubleshooting ● AUTO button not working properly ● ● The Auto Function is designed for use on standard Macintosh or IBM-compatible PCs running Microsoft Windows. It may not work properly if using nonstandard PC or video card. The AUTO adjustment does not function when digital input is used for display. Imaging Problems ● ● Display position is incorrect ● Image vibrates on the screen Press the Auto button.
Troubleshooting ● An after-image remains after the power has been turned off. ● Green, red, blue, dark, and white dots remains This is characteristic of liquid crystal and is not caused by a malfunction or deterioration of the liquid crystal. The after-image will disappear after a peroid of time. The remaining dots are normal characteristic of the liquid crystal used in today’s technology.
Regulatory Information • TCO'99 Information • TCO'99 Environmental Requirements • TCO'03 Information • Recycling Information for Customers CE Declaration • of Conformity Energy Star • Declaration • Federal Communications Commission (FCC) Notice (U. S.
Regulatory Information • Philips End-ofLife Disposal Information for • UK only • Troubleshooting Other Related • Information • Frequently Asked Questions (FAQs) Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.
Regulatory Information The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with increased risks e.g. skin cancer (malignant melanoma) as a consequence.
Regulatory Information ● ● Energy-saving mode after a certain time-beneficial both for the user and the environment Electrical safety Emissions ● ● Electromagnetic fields Noise emissions Ecology ● ● The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on ❍ chlorinated and brominated flame retardants and polymers ❍ heavy metals such as cadmium, mercury and lead.
Regulatory Information Information Center in each country or the following team of Environmental specialist can help. Mr. Job Chiu - Environment manager Philips Electronics Industries (Taiwan) Ltd, Monitor Business Unit E-mail: job.chiu@philips.com Tel: +886 (0) 3 454 9839 Mr. Maarten ten Houten - Senior Environmental Consultant Philips Consumer Electronics E-mail: marten.ten.houten@philips.com Tel: +31 (0) 40 27 33402 Mr. Delmer F. Teglas Philips Consumer Electronics North America E-mail: butch.
Regulatory Information PHILIPS 170B5 This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94. Time settings are adjusted from the system unit by software. NUTEK VESA State LED Indicator Power Consumption Normal operation ON Green < 40 W (typ.
Regulatory Information To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture. THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS. RETURN TO TOP OF THE PAGE Commission Federale de la Communication (FCC Declaration) Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC.
Regulatory Information RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
Regulatory Information Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
Regulatory Information RETURN TO TOP OF THE PAGE North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. file:///D|/My%20documents/dfu/W7/english/170b5/safety/regs/regulat.
Regulatory Information Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
Regulatory Information Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge). Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger. ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
Regulatory Information pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.
Other Related Information • Safety and Troubleshooting • FAQs Other Related Information • Troubleshooting Information for Users in the U. S. • Regulatory Information • Information for Users in the U.S • Information for Users Outside the U.S For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
SmartManage • Product Information • Philips Pixel Defect Policy • SmartManage Introduction • SmartManage Features and Benefits • Philips SmartControl • Q&A SmartManage Introduction Philips SmartManage is an advanced solution for users, corporate users in particular, to manage their Philips monitors as part of the asset management environment. The solution includes three essential components, Philips SmartManage Administrator, and Philips SmarControl and Agent.
SmartManage ● All Philips monitors supporting DDC/CI interface 2. Installation How to download "SmartControl Installation " file: 1. 2. 3. 4. 5. 6. Visit http:// www.philips.com Select "your country" Click into "PC stuff or monitors" page Select "Manuals/drivers" Enter "Download" page Select "SmartControl Installation", and you can download SmartControl and its driver for installation. Please follow the guidance in the SmartControl installation program. 3.
SmartManage ● ● Product Information Click Product Information in the left pane to view the product information stored in the monitor's memory. General Click on general, users will be able to know some general information such as driver information, device information and monitor control. file:///D|/My%20documents/dfu/W7/english/170b5/product/smart.
SmartManage Within monitor control, users can click on Auto Setup to achieve optimum performance or click on factory reset to reset the parameters of the monitor. Such choices are disabled when using DVI-D (digit) input. Q&A Q1. What is the difference between SmartManage, SmartControl? A.
SmartManage A. It might be your graphic adaptor is not compatible with the SmartControl. If your graphic adaptor is one of the above mentioned brands, try to download the most updated graphic adaptor driver from corresponding companies' web site. Install the driver. Remove SmartControl, and re-install it once more. If it is still not working, we are sorry that the graphic adaptor is not supported. Please pay attention to Philips' web site for any updated SmartControl driver available. Q5.
Philips Pixel Defect Policy • SmartManage • Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips Pixel Defect Policy Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control.
Philips Pixel Defect Policy One lit red, green or blue sub pixel Two adjacent lit sub pixels: - Red + Blue = Purple Three adjacent lit sub pixels - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) (one white pixel) Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'.
Philips Pixel Defect Policy 2 adjacent lit subpixels 0 0 2 or fewer 3 adjacent lit subpixels (one white pixel) 0 0 0 Distance between two bright dot defects* 0 0 15 mm or more Total bright dot defects of all types 0 0 4 or fewer BLACK DOT DEFECTS ACCEPTABLE LEVEL 170P5 170B5 170S5 1 dark subpixel 4 or fewer 4 or fewer 4 or fewer 2 adjacent dark subpixels 1 or fewer 1 or fewer 2 or fewer 3 adjacent dark subpixels 0 0 0 15 mm or more 15 mm or more 15 mm or more 4 or fewer
Philips Pixel Defect Policy * 1 or 2 adjacent sub pixel defects = 1 dot defect All Philips monitors are ISO13406-2 Compliant RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/170b5/product/pixel.
Connecting to Your PC Connecting to Your PC • Front View Product Accessory Pack Description • Accessory Unpack all the parts. Pack • Connecting to Your PC • Getting Started • Optimizing Power cord Performance • The Base PC audio cable (lime) VGA signal cable EDFU pack Mac adaptor (optional) RETURN TO TOP OF THE PAGE Connecting to Your PC 1) Plug the power cord into monitor firmly. file:///D|/My%20documents/dfu/W7/english/170b5/install/connect.
Connecting to Your PC Note: If you use an Apple Macintosh, you need to connect the special Mac adapter to one end of the monitor signal cable Cable management a) Remove the top cover of the arm box b) Put the cables inside the arm box c) Put the top cover back file:///D|/My%20documents/dfu/W7/english/170b5/install/connect.
Connecting to Your PC 2) Connect to PC (a) Turn off your computer and unplug its power cable. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Plug the power cord of your computer and your monitor into a nearby outlet. (d) Turn on your computer and monitor. If the monitor displays an image, installation is complete. RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/170b5/install/connect.
The Base The Base • Front View Product Unfold and Fold the Base Description • Accessory Unfold the Base Pack • Connecting to your PC • Getting Started • Optimizing Performance • Unfold the Base • Fold the Base • Remove the Base 1) Put monitor face down on the safe surface. 2) Pull up the base. Fold the Base file:///D|/My%20documents/dfu/W7/english/170b5/install/base.
The Base 1) Push down the head of monitor. RETURN TO TOP OF THE PAGE Remove the Base Condition: ● for VESA standard mounting applications file:///D|/My%20documents/dfu/W7/english/170b5/install/base.
The Base 1) Remove the top cover. 2) Remove the 4 screws and then remove the base from the LCD monitor. Note: This monitor accepts a 100mmx100mm VESA-Compliant mounting interface. file:///D|/My%20documents/dfu/W7/english/170b5/install/base.
The Base RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/170b5/install/base.
Getting Started Your LCD Monitor : Getting Started • Front View Product Description Getting Started • Connecting to Your PC Use the information file ( .inf) for Windows® 95/98/2000/Me/XP or later • Getting Started The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for • Optimizing Windows® 95/98/2000/Me/XP. This information file ( .
Getting Started 6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button. 7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then click on 'Next' and then click on 'Have Disk...'. 8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button. 9. Click on the 'OK' button, select your monitor model and click on the 'Next' button. 10.
Getting Started dialog box. If your Windows® 95/98/2000/Me/XP version is different or you need more detailed installation information, please refer to Windows® 95/98/2000/Me/XP user's manual. RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/W7/english/170b5/install/gt_start.
Your Philips F1rst Choice Warranty Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty.
Your Philips F1rst Choice Warranty ● ● ● ● Reception problems caused by signal conditions or cable or antenna systems outside the unit; Defects caused by abuse or misuse of the monitor; Product requires modification or adaptation to enable it to comply with local or national technical standards, which apply in countries for which the product was not originally designed, manufactured, approved and/or authorized. Therefore always check whether a product can be used in a specific country.
Your Philips F1rst Choice Warranty file:///D|/My%20documents/dfu/W7/english/warranty/war_1st.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
International Guarantee file:///D|/My%20documents/dfu/W7/english/warranty/war_intl.
United States Guarantee LIMITED WARRANTY (Computer Monitor) Click here to access the Warranty Registration Card. Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. This product must be shipped in at your expense for service during years two and three. WHO IS COVERED? You must have proof of purchase to receive warranty service.
United States Guarantee ● ● repair of products damaged by these modifications. incidental or consequential damages resulting from the product. (Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not copyrighted.) a product used for commercial or institutional purposes.
United States Guarantee TO GET WARRANTY SERVICE IN CANADA... Please contact Philips at: (800) 479-6696 Three years free parts and three years free labor will be provided at Philips Canada depot or any one of its authorized service centers. (In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed or implied, including any implied warranties of merchantability or fitness for a particular purpose.
F1rst Choice Contact Information F1rst Choice Contact Information Telephone numbers: Austria 01 546 575 603 Luxembourg 026 84 3000 Belgium 02 275 0701 Netherlands 053 482 9800 Cyprus (Greek) 800 92256 Norway 22 70 82 50 Denmark 35 25 87 61 Portugal 0800 831 363 France 03 8717 0033 Sweden 08 632 0016 Germany 0696 698 4712 Switzerland 02 23 10 21 16 Greece 00800 3122 1223 Spain 09 17 45 62 46 Finland 09 2290 1908 United Kingdom 0207 949 0069 Ireland 01 601 1161 Italy 02 48
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Czech Republic • Dubai • Egypt • Hong Kong • Hungary • India • Indonesia • Korea • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Russia • Singapore • Slovakia • Slovenia • South Africa • Taiwan • Thailand • Turkey • Uruguay • Venezuela Eastern Europe CZECH REPUBLIC Xpectrum Lužná 591/4 CZ - 160 00 Praha 6 Pho
Consumer Information Centers SLOVENIA PC HAND Brezovce 10 SI - 1236 Trzin Phone: +386 1 530 08 24 Email: servis@pchand.si POLAND Zolter ul.Zytnia 1 PL - 05-500 Piaseczno Phone:+48 22 7501766 Email: servmonitor@zolter.com.pl www.zolter.com.pl RUSSIA Phone: +7 095 961-1111 Phone: 8-800-200-0880 Web-site: www.philips.ru TURKEY Türk Philips Ticaret A.S. Yukari Dudullu Org.San.Bolgesi 2.Cadde No:22 34776-Umraniye/Istanbul Phone: (0800)-261 33 02 Latin America ANTILLES Philips Antillana N.V. Kaminda A.J.E.
Consumer Information Centers ARGENTINA Philips Antillana N.V. Vedia 3892 Capital Federal CP: 1430 Buenos Aires Phone: (011)-4544 2047 BRASIL Philips da Amazônia Ind. Elet. Ltda. Av. Luis Carlos Berrini, 1400 - Sao Paulo -SP Phone: 0800-701-0203 CHILE Philips Chilena S.A. Avenida Santa Maria 0760 P.O. box 2687Santiago de Chile Phone: (02)-730 2000 Fax : (02)-777 6730 COLOMBIA Industrias Philips de Colombia S.A.-Division de Servicio CARRERA 15 Nr.
Consumer Information Centers PARAGUAY Philips del Paraguay S.A. Avenida Artigas 1513 Casilla de Correos 605 Asuncion Phone: (021)-211666 Fax : (021)-213007 PERU Philips Peruana S.A. Customer Desk Comandante Espinar 719 Casilla 1841 Limab18 Phone: (01)-2136200 Fax : (01)-2136276 URUGUAY Ind.Philips del Uruguay S.A. Luis Alberto de Herrera 1248 Customer Help Desk 11300 Montevideo Phone: (02)-6281111 Fax : (02)-6287777 VENEZUELA Industrias Venezolanas Philips S.A.
Consumer Information Centers CANADA Philips Electronics Ltd. 281 Hillmount Road Markham, Ontario L6C 2S3 Phone: (800) 479-6696 Pacific AUSTRALIA Philips Consumer Service. Customer Information Centre. 3 Figtree Drive Homebush Bay NSW 2140 Phone: CIC: 1300-363 391 PCE Service: 1300-361 392 (toll free) Fax : +61 2 9947 0063 NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O.
Consumer Information Centers CHINA BEIJING Beijing Authorized Service Centre. Consumer Information Centre Building 6, West Street Chong Wen Men, Beijing, Jin Bang Co. Led. 100051 BEIJING GUANGZHOU Philips Authorized Service Centre 801 Dong Feng Road East Guangzhou 510080 SHANGHAI Philips Service Logistic Centre Consumer Information Centre P.O.
Consumer Information Centers INDIA Phone: 91-20-712 2048 ext: 2765 Fax: 91-20-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr. A Besant Road, Worli Bombay 400 025 CALCUTTA Customer Relation Centre 7 justice Chandra Madhab Road Calcutta 700 020 MADRAS Customer Relation Centre 3, Haddows Road Madras 600 006 NEW DELHI Customer Relation Centre 68, Shivaji Marg New Dehli 110 015 INDONESIA Philips Group of Companies in Indonesia Consumer Information Centre Jl.Buncit Raya Kav.
Consumer Information Centers KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone:080-600-6600 (Local toll free) Fax : (02)-709-1245 MALAYSIA Philips Malaysia Sdn. Berhad Service Dept. No.51,sect.13 Jalan University. 46200 Petaling Jaya, Selagor. P.O.box 12163 50768 Kuala Lumpur. Phone: (03)-7950 5501/02 Fax : (03)-7954 8504 PAKISTAN KARACHI Philips Electrical Ind. of Pakistan Consumer Information Centre F-54, S.I.T.E, P.O.
Consumer Information Centers PHILIPPINES Philips Electronics and Lighting Inc. 106 Valero St., Salcedo Village Makati, Metro Manilla. Phone: (02)-888 05 72 Domestic toll free: 1-800-10-PHILIPS or 1-800-10-744 5477 Fax : (02)-888 05 71 SINGAPORE Philips Singapore Private Ltd. Consumer Service Dept. Lorong 1,Toa Payoh., P.O. box 340 Singapore 1231 Phone: 6882 3999 Fax : 6250 8037 TAIWAN Philips Taiwan Ltd. Consumer Information Centre 13F, No. 3-1 Yuan Qu St., Nan Gang Dist.
Consumer Information Centers MOROCCO Philips Electronique Maroc 304,BD Mohamed V Casablanca Phone: (02)-302992 Fax : (02)-303446 SOUTH AFRICA South African Philips. S.V. Div. 195 Main R.D. Martindale., Johannesburg P.O.box 58088 Newville 2114 Phone: +27 11 471 5000 Fax : +27 11 471 5020 Middle East DUBAI Philips Middle East B.V. Consumer Information Centre P.O.
Consumer Information Centers file:///D|/My%20documents/dfu/W7/english/warranty/warcic.
