e-Manual Philips LCD Monitor Electronic User’s Manual file:///D|/My%20Documents/dfu/A7/english/170b6/index.
Safety and Troubleshooting Information • Safety Precautions and Maintenance • FAQs Safety and Troubleshooting Information Safety precautions and maintenance • Troubleshooting WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.
Safety and Troubleshooting Information ❍ Humidity: 20-80% RH Service: ● ● ● ● The casing cover should be opened only by qualified service personnel. If there is any need for any document for repair or integration, please contact with your local service center. (please refer to the chapter of "Consumer Information Center") For transportation information, please refer to "Physical Specifications". Do not leave your monitor in a car/trunk under direct sun light.
About This Manual • About This Guide • Notational Descriptions About This Manual About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other important information. Its contents are identical to the information in our printed version.
About This Manual NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may not be accompanied by an icon.
Product Information • SmartManage • Product Product Information Features • Lead-free Product • Technical Product Features Specifications • Resolution & 170B6 Preset Modes • Philips Pixel ● Outstanding front of screen performance Defect Policy ❍ Perfect panel™ for defect-free display • Automatic ❍ Fast 8ms response time displays fast moving pictures better Power Saving ❍ SXGA 1280 x 1024 resolution for sharper display ❍ Dual input accepts both analog VGA and digital DVI signals • Physical ● Best total cost
Product Information • Pixel Pitch 0.264 x 0.264 mm • LCD Panel type 1280 x 1024 pixels R.G.B. vertical stripe Anti-glare polarizer, hard coated • Effective viewing area 337.9 x 270.3 mm • Display Colors 16.2 M colors SCANNING Vertical refresh rate 56 Hz-76 Hz Horizontal Frequency 30k Hz-83 kHz VIDEO • Video dot rate 140 MHz • Input impedance - Video - Sync 75 ohm 2.
Product Information • White Chromaticity • Viewing Angle (C/R>5) • Response time x: 0.283 y: 0.297 (at 9300°K) x: 0.313 y: 0.329 (at 6500°K) x: 0.313 y: 0.329 (at sRGB) Upper >60° (typ.) Lower >80° (typ.) Left >80° (typ.) Right >80° (typ.) < 8 ms (typ.) * This data is subject to change without notice. RETURN TO TOP OF THE PAGE Resolution & Preset Modes • Maximum 1280 x 1024 at 75 Hz • Recommended 1280 x 1024 at 60 Hz 50 user definable modes 15 factory preset modes: H. freq (kHz) Resolution V.
Product Information 71.8 1152*900 76 63.9 1280*1024 60 80.0 1280*1024 75 RETURN TO TOP OF THE PAGE Automatic Power Saving If you have VESA DPMS and DVI DMPM for digital compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
Product Information • Temperature 5° C to 40° C (operating) -20° C to 60° C (storage) • Relative humidity 20% to 80% • System MTBF 50K hours (including CCFL 40K hours) • Altitude Storage/shipment: 0-40,000 feet (12,192m) Operating: 0-12,000 feet (3657.6m) * This data is subject to change without notice. * Resolution 1280x1024, standard size, brightness max., contrast 50%, 6500° K, full white pattern. RETURN TO TOP OF THE PAGE Pin Assignment 1.
Product Information 2. The 15-pin D-sub connector (male) of the signal cable: Pin Assignment No. Pin Assignment No. 1 Red video input 9 +5V 2 Green video input/SOG 10 Logic ground 3 Blue video input 11 Ground 4 Sense (GND) 12 Serial data line (SDA) 5 Hot Plug Detect 13 H. Sync / H+V 6 Red video ground 14 V.
Product Information 1) Tilt 2) Swivel RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/A7/english/170b6/product/product.
Product Information file:///D|/My%20Documents/dfu/A7/english/170b6/product/product.
Installing Your LCD Monitor Installing Your LCD Monitor Front View • Produt Description Connecting • to Your PC Front View Product Description • The Base Getting Started Optimizing • Performance • UP and DOWN buttons are used when adjusting the OSD of your monitor. LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. BRIGHTNESS hotkey. When the UP and DOWN arrow buttons are pressed, the adjustment controls for the BRIGHTNESS will show up.
Installing Your LCD Monitor RETURN TO TOP OF THE PAGE Rear View 1 Kensington anti-thief lock 2 VGA input 3 DVI-D input 4 PC audio input 5 Earphone jack 6 AC power input 7 USB upstream port 8 USB downstream port RETURN TO TOP OF THE PAGE Optimizing Performance ● For best performance, ensure that your display settings are set at 1280x1024, 60Hz. file:///D|/My%20Documents/dfu/A7/english/170b6/install/install.
Installing Your LCD Monitor Note: You can check the current display settings by pressing the 'OK' button once. Go into the Product Information. The current display mode is shown on the item called RESOLUTION. ● You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance out of your monitor. This is included on this CD. Step-by-step instructions are provided to guide you through the installtion process. Click on the link to know more about this program.
On-Screen Display On-Screen Display • Description of the OnScreen Display Description of the On Screen Display The OSD • Tree What is the On-Screen Display? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display interface is shown as below : Basic and simple instruction on the control keys.
On-Screen Display Note: sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.) file:///D|/My%20Documents/dfu/A7/english/170b6/osd/osddesc.
On-Screen Display Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen. Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in the monitor's OSD.
Customer Care & Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Slovakia • Slovenia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • P
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ A Active matrix This is a kind of liquid crystal display structure in which switching transistors are attached to each pixel to control the on/off voltage. It produces a brighter and sharper display with a broader viewing angle than a passive matrix display. Also refer to TFT (thin film transistor). Amorphous silicon (a-Si) A semiconductor material that is used to make the thin film transistors (TFTs) layer of an active matrix LCD.
Glossary C CCFL(cold cathode fluorescent light) These are the fluorescent light tubes providing the light for the LCD module. These tubes are generally very thin, approximately 2 mm in diameter. Chromaticity That part of color specification, which does not involve illuminance. Chromaticity is two-dimensional and specified by pairs of numbers such as dominant wavelength and purity.
Glossary D D-SUB A VGA Analog input connector. Your monitor comes with a D-Sub cable. Digital Visual Interface (DVI) The Digital Visual Interface (DVI) specification provides a high-speed digital connection for visual data types that is display technology independent. The interface is primarily focused at providing a connection between a computer and its display device. The DVI specification meets the needs of all segments of the PC industry (workstation, desktop, laptop, etc.
Glossary RETURN TO TOP OF THE PAGE G Gamma Screen luminance as a function of video voltage approximately follows a mathematical power function of the input video signal, the exponent of which is called gamma. Grayscale An achromatic scale ranging from black through a series of successively lighter grays to white. Such a series may be made up of steps, which appear to be equally distant from one another. If the Analog/ Digital converter is 8 bit, then the monitor can display at most 28 = 256 levels.
Glossary L LCD (liquid crystal display) A display composed of liquid crystal suspended between two transparent sheets. The display is composed thousands of pixels which can be turned on or off with electrical stimulation. Thus, colorful images/texts can be generated. Liquid crystal The compound found in liquid crystal displays. Liquid crystal reacts predictably when electrically stimulated. This makes it the ideal compound to turn LCD pixels "on" or "off." Liquid crystal is sometimes abbreviated as LC.
Glossary A light filter which only allows light waves of a certain rotation through. Polarized material with perpendicular filtering is used in LCDs to enclose the liquid crystal. The liquid crystal is then used as the medium which twists the light waves 90° in order to allow the light to pass through or not. R Refresh rate The number of times per second the screen is refreshed or redrawn. This number is usually stated in Hz (Hertz) or cycles per second. A rate of 60 Hz is equal to 60 tomes per second.
Glossary TFT(thin film transistor) Usually made from amorphous silicon (a-Si) and used as a switch to a charge storage device located below each sub-pixel on an active matrix LCD. U USB or Universal Serial Bus A smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals. USB makes necessary resources available without user intervention.
Glossary controlled switch between the upstream port and downstream ports. It also has hardware support for reset and suspend/resume signaling. The controller provides the interface registers to allow communication to/from the host. Hub specific status and control commands permit the host to configure a hub and to monitor and control its ports. Device A logical or physical entity that performs a function. The actual entity described depends on the context of the reference.
Glossary RETURN TO TOP OF THE PAGE V Vertical refresh rate Expressed in Hz, it is the number of frames (complete pictures) written to the screen every second. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/A7/english/170b6/glossary/glossary.
Download and Print Download and Print • Installing your LCD monitor driver Installing Your LCD monitor driver • Download and System requirements: Printing Instructions ● PC running Windows 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP or later Installing ● Find your driver ".inf/.icm/.cat" at : lcd\pc\drivers • FPadjust Program Read the "Readme.txt" file before installing. This page provides an option to read the manual in .pdf format.
Download and Print Printing instructions: To print the manual: 1. With the manual file open, follow your printer's instructions and print the pages you need. RETURN TO TOP OF THE PAGE Installing FPadjust Program The FP Adjust program generates alignment patterns which will help you adjust monitor settings such as CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL POSITION, PHASE and CLOCK.
Download and Print RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/A7/english/download/download.
FAQs (Frequently Asked Questions) • Safety and Troubleshooting • General FAQs FAQs (Frequently Asked Questions) • Screen General FAQs Adjustments • Compatibility Q: When I install my monitor what should I do if the screen shows 'Cannot display this video with Other mode'? Peripherals • LCD Panel A: Recommended video mode for Philips 17": 1280x1024 @60Hz. Technology • Ergonomics, 1. Unplug all cables, then connect your PC to the monitor that you used Ecology and previously. Safety 2.
FAQs (Frequently Asked Questions) A: The refresh rate is of much less relevance for LCD monitors. LCD monitors display a stable, flicker-free image at 60Hz. There is no visible difference between 85Hz and 60Hz. Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and . icm)? A: These are the driver files for your monitor. Follow the instructions in your user manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .
FAQs (Frequently Asked Questions) scanning lines at the same time, thus distorting the picture. Q: What does the Refresh Rate mean for LCD? A: Unlike CRT display technology, in which the speed of the electron beam is swept from the top to the bottom of the screen determines flicker, an active matrix display uses an active element (TFT) to control each individual pixel and the refresh rate is therefore not really applicable to LCD technology.
FAQs (Frequently Asked Questions) Q: What is the FPadjust program on the CD-ROM? A: The FPadjust program generates alignment patterns that help you adjust monitor settings such as Contrast, Brightness, Horizontal Position, Vertical Position, Phase and Clock for optimal performance. Q: When I install my monitor, how do I get the best performance from the monitor? A: 1. For best performance, make sure your display settings are set at 1280x1024@60Hz for 17".
FAQs (Frequently Asked Questions) Q: What is USB (Universal Serial Bus)? A: Think of USB as a smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals. USB makes necessary resources available without user intervention. There are three main benefits of USB.
FAQs (Frequently Asked Questions) principle of blocking light rather than emitting it. Q: How are LCDs made? A: LCDs are created from two glass plates separated from each other at a distance of a few microns. The plates are filled with liquid crystal and then sealed together. The top plate is colored with an RGB pattern to make the color filter. Polarizers are then glued to both plates. This combination is sometimes called 'glass' or 'cell.
FAQs (Frequently Asked Questions) A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized electrons on fluorescent glass. Therefore, CRT monitors basically operate with an analog RGB signal. A TFT LCD monitor is a device that displays an input image by operating a liquid crystal panel. The TFT has a fundamentally different structure than a CRT: Each cell has an active matrix structure and independent active elements.
FAQs (Frequently Asked Questions) RETURN TO TOP OF THE PAGE Ergonomics, Ecology and Safety Standards Q: What is the CE mark? A: The CE (Conformité Européenne) mark is required to be displayed on all regulated products offered for sale on the European market. This 'CE' mark means that a product complies with the relevant European Directive. A European Directive is a European 'Law' that relates to health, safety, environment and consumer protection, much the same as the U.S.
Troubleshooting Troubleshooting • Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • Regulatory Information • Other Related Information This page deals with problems that can be corrected by the user. If the problem still persists after you have tried these solutions, contact your nearest Philips dealer.
Troubleshooting ● AUTO button not working properly ● ● The Auto Function is designed for use on standard Macintosh or IBM-compatible PCs running Microsoft Windows. It may not work properly if using nonstandard PC or video card. The AUTO adjustment does not function when digital input is used for display. Imaging Problems ● ● Display position is incorrect ● Image vibrates on the screen Press the Auto button.
Troubleshooting ● An after-image remains after the power has been turned off. ● Green, red, blue, dark, and white dots remains This is characteristic of liquid crystal and is not caused by a malfunction or deterioration of the liquid crystal. The after-image will disappear after a peroid of time. The remaining dots are normal characteristic of the liquid crystal used in today’s technology.
Regulatory Information • TCO'99 Information • TCO'99 Environmental Requirements • TCO'03 Information • Recycling Information for Customers CE Declaration • of Conformity Energy Star • Declaration • Federal Communications Commission (FCC) Notice (U. S.
Regulatory Information • Philips End-ofLife Disposal Information for • UK only • Troubleshooting Other Related • Information • Frequently Asked Questions (FAQs) Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.
Regulatory Information The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with increased risks e.g. skin cancer (malignant melanoma) as a consequence.
Regulatory Information ● ● Energy-saving mode after a certain time-beneficial both for the user and the environment Electrical safety Emissions ● ● Electromagnetic fields Noise emissions Ecology ● ● The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on ❍ chlorinated and brominated flame retardants and polymers ❍ heavy metals such as cadmium, mercury and lead.
Regulatory Information Information Center in each country or the following team of Environmental specialist can help. Mr. Job Chiu - Environment manager Philips Electronics Industries (Taiwan) Ltd, Monitor Business Unit E-mail: job.chiu@philips.com Tel: +886 (0) 3 454 9839 Mr. Maarten ten Houten - Senior Environmental Consultant Philips Consumer Electronics E-mail: marten.ten.houten@philips.com Tel: +31 (0) 40 27 33402 Mr. Delmer F. Teglas Philips Consumer Electronics North America E-mail: butch.
Regulatory Information PHILIPS 170B6 This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard and also DVI Digital Monitor Power Management (DMPM) standard. This means that the monitor must be connected to a computer which supports VESA DPMS for analog and DVI DMPM for digital to fulfill the requirements in the NUTEK specification 803299/94. Time settings are adjusted from the system unit by software.
Regulatory Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
Regulatory Information RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
Regulatory Information Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
Regulatory Information North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Regulatory Information Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften. Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind.
Regulatory Information WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A. S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3pin plug fitted in its place.
Regulatory Information terminal which marked with the letter "L" or coloured RED. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/A7/english/170b6/safety/regs/regulat.
Other Related Information • Safety and Troubleshooting • FAQs Other Related Information • Troubleshooting Information for Users in the U. S. • Regulatory Information • Information for Users in the U.S • Information for Users Outside the U.S For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
SmartManage • Product Information • Philips Pixel Defect Policy • SmartManage Introduction • SmartManage Features and Benefits • Philips SmartControl • Q&A SmartManage Introduction Philips SmartManage is an advanced solution for users, corporate/institution IT administrator in particular, to manage their Philips monitors as part of the asset management environment. The solution includes three essential components, Philips SmartManage Administrator, and Philips SmarControl and Agent.
SmartManage The SmartControl and SmartManage Agent are deployed and installed in computers using Philips monitors. With SmartControl and SmartManage Agent, monitors and PCs can interact with the administrator's inquiries. Because SmartControl operates on individual PC, end users can also use SmartControl to adjust monitor's performance settings. 1.
SmartManage ● ● Position Users can adjust the horizontal and vertical position of the screen by moving the sliding bar left and right. This function is disabled when using DVI-D (digit) input. Product Information Click Product Information in the left pane to view the product information stored in the monitor's memory. file:///D|/My%20Documents/dfu/A7/english/170b6/product/smart.
SmartManage ● General Click on General for general information including driver information, device information, and monitor control. Within monitor control, users can click on Auto Setup to achieve optimum performance or click on factory reset to reset the parameters of the monitor. Such choices are disabled when using DVI-D (digit) input. Q&A Q1. What is the difference between SmartManage, SmartControl? A.
SmartManage Q2. I change the monitor on a PC to a different one and the SmartControl becomes un-usable, what do I do? A. Restart your PC and see if SmartControl can work. Otherwise, you will need to remove and reinstall SmartControl to ensure proper driver is installed. Q3. The SmartControl functions well at the beginning, but it is not workable, what can I do? A. If the following actions were executed, the monitor driver may need to be re-installed.
Philips Pixel Defect Policy • SmartManage • Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips Pixel Defect Policy Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control.
Philips Pixel Defect Policy One lit red, green or blue sub pixel Two adjacent lit sub pixels: - Red + Blue = Purple Three adjacent lit sub pixels - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) (one white pixel) A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots. Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'.
Philips Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL 170P6 170B6 170S6 1 lit subpixel 0 0 4 or fewer 2 adjacent lit subpixels 0 0 2 or fewer 3 adjacent lit subpixels (one white pixel) 0 0 0 Distance between two bright dot defects* 0 0 15 mm or more Total bright dot defects of all types 0 0 4 or fewer MODEL BLACK DOT DEFECTS ACCEPTABLE LEVEL 170P6 170B6 170S6 1 dark subpixel 0 0 4 or fewer 2 adjacent dark subpixels 0 0 2 or fewer 3 adjacent dark subpixels 0
Philips Pixel Defect Policy Note: * 1 or 2 adjacent sub pixel defects = 1 dot defect All Philips monitors are ISO13406-2 Compliant RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/A7/english/170b6/product/pixel.
Connecting to Your PC Connecting to Your PC • Front View Product Accessory Pack Description • Accessory Unpack all the parts. Pack • Connecting to Your PC • Getting Started • Optimizing Power cord Performance • The Base PC audio cable (lime) VGA signal cable EDFU pack Mac adaptor (optional) USB cable DVI Cable (for /27 and /96 only) RETURN TO TOP OF THE PAGE Connecting to Your PC file:///D|/My%20Documents/dfu/A7/english/170b6/install/connect.
Connecting to Your PC 1) Plug the power cord into monitor firmly. file:///D|/My%20Documents/dfu/A7/english/170b6/install/connect.
Connecting to Your PC Note: If you use an Apple Macintosh, you need to connect the special Mac adapter to one end of the monitor signal cable file:///D|/My%20Documents/dfu/A7/english/170b6/install/connect.
Connecting to Your PC Cable management a) Remove the top cover of the arm box b) Put the cables inside the arm box c) Put the top cover back file:///D|/My%20Documents/dfu/A7/english/170b6/install/connect.
Connecting to Your PC 2) Connect to PC (a) Turn off your computer and unplug its power cable. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Plug the power cord of your computer and your monitor into a nearby outlet. (d) Turn on your computer and monitor. If the monitor displays an image, installation is complete. 3) USB plug file:///D|/My%20Documents/dfu/A7/english/170b6/install/connect.
Connecting to Your PC (a) (b) Connect USB upstream port on monitor and the USB port on PC with a USB cable. The USB downstream port is now ready for any USB device to plug in Note: The USB plug is a pass through connection whether it can support USB 1.1 or USB 2.0 depends on your PC's specification. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/A7/english/170b6/install/connect.
The Base The Base • Front View Product Unfold and Fold the Base Description • Accessory Unfold the Base Pack • Connecting to your PC • Getting Started • Optimizing Performance • Unfold the Base • Fold the Base • Remove the Base 1) Put monitor face down on the safe surface. 2) Pull up the base. Fold the Base file:///D|/My%20Documents/dfu/A7/english/170b6/install/base.
The Base 1) Push down the head of monitor. RETURN TO TOP OF THE PAGE Remove the Base Condition: ● for VESA standard mounting applications file:///D|/My%20Documents/dfu/A7/english/170b6/install/base.
The Base 1) Remove the top cover. 2) Remove the 4 screws and then remove the base from the LCD monitor. file:///D|/My%20Documents/dfu/A7/english/170b6/install/base.
The Base Note: This monitor accepts a 100mmx100mm VESACompliant mounting interface. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/A7/english/170b6/install/base.
Getting Started Your LCD Monitor : Getting Started • Front View Product Description Getting Started • Connecting to Your PC Use the information file ( .inf) for Windows® 95/98/2000/Me/XP or later • Getting Started The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for • Optimizing Windows® 95/98/2000/Me/XP. This information file ( .
Getting Started 6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button. 7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then click on 'Next' and then click on 'Have Disk...'. 8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button. 9. Click on the 'OK' button, select your monitor model and click on the 'Next' button. 10.
Getting Started dialog box. If your Windows® 95/98/2000/Me/XP version is different or you need more detailed installation information, please refer to Windows® 95/98/2000/Me/XP user's manual. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/A7/english/170b6/install/gt_start.
Your Philips F1rst Choice Warranty Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty.
Your Philips F1rst Choice Warranty ● ● ● ● Reception problems caused by signal conditions or cable or antenna systems outside the unit; Defects caused by abuse or misuse of the monitor; Product requires modification or adaptation to enable it to comply with local or national technical standards, which apply in countries for which the product was not originally designed, manufactured, approved and/or authorized. Therefore always check whether a product can be used in a specific country.
Your Philips F1rst Choice Warranty file:///D|/My%20Documents/dfu/A7/english/warranty/war_1st.
International Guarantee Your Guarantee in Central and Eastern Europe Dear Customer, Thank you for purchasing this Philips product, which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts during a period of 36 months from date of purchase.
International Guarantee Therefore always check whether a product can be used in a specific country. Just a click away In case of any problems, we advise you to read the operating instructions carefully or go to the www. philips.com/support website for additional support.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
F1rst Choice Contact Information F1rst Choice Contact Information Country Telephone number Tariff Austria 01 546 575 603 Local call tariff Belgium 070 253 010 0.17 Cyprus 800 92256 Free of Charge Denmark 3525 8761 Local call tariff Finland 09 2290 1908 Local call tariff France 08 9165 0006 0.23 Germany 0180 5 007 532 0.12 Greece 00800 3122 1223 Local call tariff Ireland 01 601 1161 Local call tariff Italy 199 404 042 0.
United States Guarantee Your Philips F1rst Choice Warranty(Canada/USA) Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
United States Guarantee Your warranty does not cover: ● ● ● ● ● ● ● labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product. product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not within the control of Philips Consumer Electronics. reception problems caused by signal conditions or cable or antenna systems outside the unit.
United States Guarantee (877) 835-1838 or (919) 573-7855 (In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of this express warranty. But, because some states do not allow limitations on how long an implied warranty may last, this limitation may not apply to you.) TO GET WARRANTY SERVICE IN CANADA...
United States Guarantee ● ● ● Other cards installed Having the following information available will also help speed up the process: Your proof of purchase indicating: date of purchase, dealer name, model and product serial number. The full address to which the swap model should be delivered. Just a phone call away Philips’ customer help desks are located worldwide. Within the U.S.
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Belarus • Bulgaria • Croatia • Czech Republic • Estonia • Dubai • Hong Kong • Hungary • India • Indonesia • Korea • Latvia • Lithuania • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Romania • Russia • Serbia & Montenegro • Singapore • Slovakia • Slovenia • South Africa • Taiwan • Thailand • Turkey • Ukraine
Consumer Information Centers ESTONIA FUJITSU SERVICES OU Akadeemia tee 21G EE-12618 Tallinn Tel: +372 6519900 www.ee.invia.fujitsu.com HUNGARY Serware Szerviz Vizimolnár u. 2-4 HU - 1031 Budapest Tel: +36 1 2426331 Email: inbox@serware.hu www.serware.hu LATVIA ServiceNet LV Jelgavas iela 36 LV - 1055 Riga, Tel: +371 7460399 Email: serviss@servicenet.lv LITHUANIA ServiceNet LT Gaiziunu G. 3 LT - 3009 KAUNAS Tel: +370 7400088 Email: servisas@servicenet.lt www.servicenet.
Consumer Information Centers SLOVAKIA Datalan Servisne Stredisko Puchovska 8 SK - 831 06 Bratislava Tel: +421 2 49207155 Email: servis@datalan.sk SLOVENIA PC HAND Brezovce 10 SI - 1236 Trzin Tel: +386 1 530 08 24 Email: servis@pchand.si POLAND Zolter ul.Zytnia 1 PL - 05-500 Piaseczno Tel: +48 22 7501766 Email: servmonitor@zolter.com.pl www.zolter.com.pl RUSSIA Tel: +7 095 961-1111 Tel: 8-800-200-0880 Website: www.philips.ru TURKEY Türk Philips Ticaret A.S. Yukari Dudullu Org.San.Bolgesi 2.
Consumer Information Centers UKRAINE Comel Shevchenko street 32 UA - 49030 Dnepropetrovsk Tel: +380 562320045 www.csp-comel.com Latin America ANTILLES Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (09)-4612799 Fax : (09)-4612772 ARGENTINA Philips Antillana N.V. Vedia 3892 Capital Federal CP: 1430 Buenos Aires Phone/Fax: (011)-4544 2047 BRASIL Philips da Amazônia Ind. Elet. Ltda.
Consumer Information Centers COLOMBIA Industrias Philips de Colombia S.A.-Division de Servicio CARRERA 15 Nr. 104-33 Bogota, Colombia Phone:(01)-8000 111001 (toll free) Fax : (01)-619-4300/619-4104 MEXICO Consumer Information Centre Norte 45 No.669 Col. Industrial Vallejo C.P.02300, -Mexico, D.F. Phone: (05)-3687788 / 9180050462 Fax : (05)-7284272 PARAGUAY Av. Rca. Argentina 1780 c/Alfredo Seiferheld P.O.
Consumer Information Centers URUGUAY Rambla O'Higgins 5303 Montevideo Uruguay Phone: (598) 619 66 66 Fax: (598) 619 77 77 Customer Desk: Phone: 0004054176 VENEZUELA Industrias Venezolanas Philips S.A. Apartado Postal 1167 Caracas 1010-A Phone: (02) 2377575 Fax : (02) 2376420 Canada CANADA Philips Electronics Ltd.
Consumer Information Centers NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (toll free) Fax : 0800 288 588 Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA SHANGHAI Rm 1007, Hongyun Building, No. 501 Wuning road, 200063 Shanghai P.R.
Consumer Information Centers INDIA Phone: 91-20-712 2048 ext: 2765 Fax: 91-20-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr. A Besant Road, Worli Bombay 400 025 CALCUTTA Customer Relation Centre 7 justice Chandra Madhab Road Calcutta 700 020 MADRAS Customer Relation Centre 3, Haddows Road Madras 600 006 NEW DELHI Customer Relation Centre 68, Shivaji Marg New Dehli 110 015 INDONESIA Philips Group of Companies in Indonesia Consumer Information Centre Jl.Buncit Raya Kav.
Consumer Information Centers KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone: 080 600 6600 (toll free) Fax : (02) 709 1210 MALAYSIA After Market Solutions Sdn Bhd, Philips Authorised Service Center, Lot 6, Jalan 225, Section 51A, 46100 Petaling Jaya, Selangor Darul Ehsan, Malaysia.
Consumer Information Centers SINGAPORE Accord Customer Care Solutions Ltd Authorized Philips Service Center Consumer Service 620A Lorong 1 Toa Rayoh Singapore 319762 Tel: +65 6882 3999 Fax: +65 6250 8037 TAIWAN Philips Taiwan Ltd. Consumer Information Centre 13F, No. 3-1 Yuan Qu St., Nan Gang Dist., Taipei 115, Taiwan Phone: 0800-231-099 Fax : (02)-3789-2641 THAILAND Philips Electronics (Thailand) Ltd.
Consumer Information Centers SOUTH AFRICA PHILIPS SA (PTY) LTD Customer Care Center 195 Main Road Martindale, Johannesburg P.O. box 58088 Newville 2114 Telephone: +27 (0) 11 471 5194 Fax: +27 (0) 11 471 5123 E-mail: phonecare.za@philips.com Middle East DUBAI Philips Middle East B.V. Consumer Information Centre P.O.Box 7785 DUBAI Phone: (04)-335 3666 Fax : (04)-335 3999 file:///D|/My%20Documents/dfu/A7/english/warranty/warcic.
