9B4 www.philips.
Table of Contents 1. Important �����������������������������������������������1 1.1 Safety precautions and maintenance �1 1.2 Notational Descriptions ���������������������������2 1.3 Disposal of product and packing material ���������������������������������������������������������������3 2. Setting up the monitor �����������������������4 2.1 Installation ���������������������������������������������������������4 2.2 Operating the monitor ������������������������������6 2.
1. Important 1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user manual before you use your monitor. It contains important information and notes regarding operating your monitor.
1. Important • Temperature: 0-40°C 32-95°F 1.2 Notational Descriptions • Humidity: 20-80% RH The following subsections describe notational conventions used in this document. Important information for Burn-in/Ghost image • • Notes, Cautions and Warnings Always activate a moving screen saver program when you leave your monitor unattended. Always activate a periodic screen refresh application if your monitor will display unchanging static content.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic EquipmentWEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install the base 2. Setting up the monitor 1. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. 2.1 Installation Package contents 19B4 2. Snap in the base in the VESA mount area.
2. Setting up the monitor 3. Hold the base with both hands. (1) Gently attach the base to the column until the three guiding pins rest into the position holes. (2) Use your fingers to tighten the screw located at the bottom of the base, and secure the base to the column tightly.
2. Setting up the monitor Connecting to your PC 2.2 Operating the monitor Description of the control buttons 5 4 2 3 2 3 1 6 4 5 1 Kensington anti-theft lock 2 VGA input 3 DVI input 4 Audio input 5 AC power input 3 6 Earphone jack Connect to PC 1. Connect the power cord to the back of the monitor firmly. 7 6 2. Turn off your computer and unplug its power cable. 5 4 2 1 Switch monitor’s power ON and OFF. 3.
2. Setting up the monitor Description of the On Screen Display The OSD Menu Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window.
2. Setting up the monitor Height adjustment Resolution notification This monitor is designed for optimal performance at its native resolution, 1280 × 1024 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1280 × 1024 @ 60 Hz for best results. 110mm Display of the native resolution alert can be switched off from Setup in the OSD (On Screen Display) menu.
2. Setting up the monitor 3. While keeping the release button pressed, tilt the base and slide it out. 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 2 1. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. 1 Note This monitor accepts a 100mm x 100mm mounting interface. 2. Remove the screws from hinge cover.
3. Image Optimization 3. Image Optimization 2. Keep pressing to toggle among Office, Photo, Movie, Game, Economy and Off. 3.1 SmartImage 3. The SmartImage on screen display will remain on screen for 5 seconds, or you can also press "OK" to make confirmation. What is it? 4. When SmartImage is enabled, the sRGB scheme is disabled automatically. To use sRGB, you need to disable SmartImage with the button at the front bezel of your monitor.
3. Image Optimization • Game: Turn on over drive circuit for best response time, reduce jaggy edges for fast moving objects on screen, enhance contrast ratio for bright and dark scheme, this profile delivers the best gaming experience for gamers. • Economy: Under this profile, brightness, contrast are adjusted and backlighting finetuned for just right display of everyday office applications and lower power consumption. • Off: No optimization by SmartImage. 3.
3. Image Optimization • You can adjust more options without wizard by Standard pane. Start with Standard pane Adjust menu • Adjust Menu allows you to adjust Brightness, Contrast, and Resolution. • You can follow the instruction and do the adjustment. • Cancel prompts user if you want to cancel installation. Color menu 12 • Color Menu allows you to adjust RGB, Black Level, White Point, Display Gamma, Calibration, SmartImage, and SmartKolor.
3. Image Optimization 1. "Show Me" starts color calibration tutorial. 2. Start - starts the 6-step color calibration sequence. 3. Quick View loads the before/after images. 4. To return to Color home pane, click the Cancel button. 5. Enable color calibration - by default is on. If unchecked, does not allow for color calibration to happen, dimes out start and quick view buttons. 6. Must have patent info in calibration screen.
3. Image Optimization First Color Calibration Screen • Previous button is disabled until the second color screen. • Next goes to the succeeding target (6-targets). • Final next goes File > Presets pane. • Cancel closes the UI and returns to the plug in page. Eco Power menu Options menu Options>Preferences - Will only be active when selecting Preferences from the dropdown Options menu. On a non-supported display capable of DDC/CI, only the Help and Options tabs are available.
3. Image Optimization Option>Auto Pivot. menu. Disabled removes SmartControl Premium from the right click context menu. • Enable Task Tray icon is checked (On) by default. Enable context menu shows the task tray menu for SmartControl Premium. A right click on the task tray icon displays the menu options for Help, Technical Support. Check for Update, About, and Exit. When Enable task tray menu is disabled, the task tray icon will only display Exit. • Run at Startup is checked (On) by default.
3. Image Optimization Help menu Options>Theft Deterrence - Theft Deterrence Pane will only be active when selecting Theft Deterrence Mode from the drop-down Plug-in menu. Help>User Manual - Will only be active when selecting User Manual from the drop-down Help menu. On a non-supported display capable of DDC/CI, only the Help and Options tabs are available. To enable Theft Deterrence, click on On button to bring up the following screen: • User can enter PIN between 4 and 9 digits numbers only.
3. Image Optimization Context Sensitive menu The task tray has five entries: The Context Sensitive menu is Enabled by default. If Enable Context Menu has been checked in the Options>Preferences pane, then the menu will be visible. • Help - Access to User Manual file: Open User Manual file using the default browser window. • Technical Support - Displays the tech support page. • Check for Update - Takes the user to PDI Landing and checks the user’s version against the most current available.
3. Image Optimization 3.4 SmartDesktop Guide When the window and mouse cursor are within the region, the region will become highlighted. SmartDesktop Note SmartDesktop is in SmartControl Premium. Install SmartControl Premium and select SmartDesktop from Options. If the outline of the region is not visible when dragging the window, “Show windows contents while dragging” is disabled. To enable: 1. In Control Panel, click System. 2.
3. Image Optimization Title Bar Options Desktop partition can be accessed from the title bar of the active window. This provides a quick and easy way to manage the desktop as well as sending any window to any partition without having to drag and drop. Move the cursor into the active window’s title bar to access the drop down menu. • Identify Partition – Displays the outline grid on the desktop for the current partition. • Align On/Align Off – Enables/disables the drag and drop auto align feature.
3. Image Optimization • Find Windows – In some cases, the user may have sent multiple windows to the same partition. Find Windows will show all open windows and move the selected window to the forefront. • Desktop Partition – Desktop Partition shows the current selected partition and allows the user to quickly change to any of the partitions shown in the drop down. • Identify Partition – Displays the outline grid on the desktop for the current partition.
3. Image Optimization SmartDesktop Partition Definitions Name Description Full Desktop Applies all settings to the entire desktop. Image Vertical Assesses the screen resolution and divides the display into two evenly sized vertical regions. For 90/270 maintain vertical configuration. Horizontal Assesses the screen resolution and divides the display into two evenly sized horizontal regions. For 90/270 maintain horizontal configuration.
3. Image Optimization Name Description Image Horizontal Split Bottom Assesses the screen resolution and divides the display into two evenly sized horizontal regions, the bottom region is single, the top region is spilt into two evenly sized regionsFor 90 Partition 1&2 on right side Vertical Partition 3 on left side Vertical.For 270 Partition 1&2 on left side Vertical Partition 3 on right side Vertical. Even Split Assesses the screen resolution and divides the display into four evenly sized regions.
4. Technical Specifications 4. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch Brightness SmartContrast Contrast Ratio (typ.
4.
4. Technical Specifications 4.1 Resolution & Preset Modes Maximum Resolution 1280 x 1024 @ 60 Hz (analog input) 1280 x 1024 @ 60 Hz (digital input) Recommended Resolution 1280 x 1024 @ 60 Hz (digital input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720x400 70.09 31.47 640x480 59.94 35.00 640x480 66.67 37.86 640x480 72.81 37.50 640x480 75.00 37.88 800x600 60.32 46.88 800x600 75.00 48.36 1024x768 60.00 60.02 1024x768 75.03 44.77 1280x720 59.86 63.89 1280x1024 60.02 79.
5. Power Management 5. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
6 Regulatory Infomation headsets) Acoustic performance – protection against sound spikes (headsets) and fan noise (projectors, computers) Ergonomically designed keyboard (notebooks) 6. Regulatory Information Congratulations! This product is TCO Certified-for Sustainable IT Electrical Safety, minimal electro-magnetic Emissions Third Party Testing All certified product models have been tested in an independent, accredited laboratory.
6. Regulatory Infomation Lead-free Product CE Declaration of Conformity Lead free display promotes environmentally sound recovery and disposal of waste from electrical and electronic equipment. Toxic substances like Lead has been eliminated and compliance with European community’s stringent RoHs directive mandating restrictions on hazardous substances in electrical and electronic equipment have been adhered to in order to make Philips monitors safe to use throughout its life cycle.
6 Regulatory Infomation Energy Star Declaration Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (www.energystar.gov) As an ENERGY STAR® Partner, we have determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.
6. Regulatory Infomation Cependant, rien ne peut garantir l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes: EN 55022 Compliance (Czech Republic Only) • Réorienter ou déplacer l’antenne de réception.
6 Regulatory Infomation North Europe (Nordic Countries) Information Ergonomie Hinweis (nur Deutschland) Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften.
6. Regulatory Infomation China RoHS 环保使用期限 The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by Electronic Information Products" or commonly referred to as China RoHS. All products produced and sold for China market have to meet China RoHS request.
7 Customer care and warranty black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 7. Customer care and warranty Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category. 7.1 Philips’ Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products.
7. Customer care and warranty Proximity of Pixel Defects Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots. Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'.
7 Customer care and warranty 7.2 Customer Care & Warranty For warranty coverage information and additional support requirement valid for your region, please visit www.philips.com/support website for details. You may also contact your local Philips Customer Care Center number listed below. Contact Information for WESTERN EUROPE region: Country CSP Hotline Number Price Opening hours Austria RTS +43 0810 000206 € 0.07 Mon to Fri : 9am - 6pm Belgium Ecare +32 078 250851 € 0.
7. Customer care and warranty Contact Information for CENTRAL AND EASTERN EUROPE region: Country Call center CSP Consumer care number Belarus N/A IBA +375 17 217 3386 +375 17 217 3389 Bulgaria N/A LAN Service +359 2 960 2360 Croatia N/A MR Service Ltd +385 (01) 640 1111 Czech Rep.
7 Customer care and warranty Contact Information for NORTH AMERICA : Country Call center Consumer care number U.S.A. EPI - e-center (877) 835-1838 Canada EPI - e-center (800)479-6696 Contact Information for APMEA region: Country ASP Consumer care number Opening hours Australia AGOS NETWORK PTY LTD 1300 360 386 Mon.~Fri. 8:00am-7:30pm 0800 657447 Mon.~Fri. 8:30am-5:30pm New Zealand Visual Group Ltd. Hong Kong Macau Hong Kong: Company: Smart Pixels Tel: +852 2619 9639 Technology Ltd.
7. Customer care and warranty Philippines EA Global Supply Chain Solutions ,Inc. (02) 655-7777; 6359456 Mon.~Fri. 8:30am~5:30pm Armenia Azerbaijan Georgia Kyrgyzstan Tajikistan Firebird service centre +97 14 8837911 Sun.~Thu. 09:00 - 18:00 Uzbekistan Soniko Plus Private Enterprise Ltd +99871 2784650 Mon.~Fri. 09:00 - 18:00 Turkmenistan Technostar Service Centre +(99312) 460733, 460957 Mon.~Fri. 09:00 - 18:00 Japan フィリプスモニター '03-5676-6022 ・サポートセンター 38 Mon.~Fri.
8. Troubleshooting & FAQs 8. Troubleshooting & FAQs Note The Auto Function is not applicable in DVIDigital mode as it is not necessary. 8.1 Troubleshooting Visible signs of smoke or sparks This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.
8. Troubleshooting & FAQs Image appears blurred, indistinct or too dark • For further assistance, refer to the Consumer Information Centers list and contact Philips customer service representative. Adjust the contrast and brightness on On-Screen Display. An "after-image", "burn-in" or "ghost image" remains after the power has been turned off. • 8.
8. Troubleshooting & FAQs Ans.: It might be your graphic adaptor is not compatible with the SmartControl Premium. If your graphic adaptor is one of the above mentioned brands, try to download the most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove SmartControl Premium, and re-install it once more. If it is still not working, we are sorry that the graphic adaptor is not supported.
8. Troubleshooting & FAQs package. Monitor drivers (.inf and .icm files) will be installed automatically. 1. Color Temperature: The six settings are 5000K, 6500K, 7500K, 8200K, 9300K and 11500K. With settings in the 5000K range the panel appears "warm, with a red-white color tone", while a 11500K temperature yields "cool, bluewhite toning". Q4: How do I adjust the resolution? Ans.: Your video card/graphic driver and monitor together determine the available resolutions.
8. Troubleshooting & FAQs may cause "burn in", also known as "after-imaging" or "ghost imaging", on your screen. "Burn-in", "after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "atter-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off. Always activate a moving screen saver program when you leave your monitor unattended.
© 2013 Koninklijke Philips Electronics N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips Electronics N.V. and are used under license from Koninklijke Philips Electronics N.V. Specifications are subject to change without notice.
