Philips Hospitality TV Installation manual for 22HFL4007D/10 26HFL4007D/10 32HFL4007D/10 42HFL4007D/10 Version 1.
Contents 1. Requirements before starting the installation.......................................................................................................... 2 2. Find out the state of the TV ...................................................................................................................................... 3 3. Re-install TV ...........................................................................................................................................................
1. Requirements before starting the installation Before starting the installation, make sure that you have everything you need at hand. Master remote control 22AV8573 or Guest remote control 22AV1109A And USB stick You will need the master remote control or the guest remote control to access the menus. To access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button. For the guest remote control, press the following keys sequential: 3, 1, 9, 7, 5, 3, ‘MUTE’.
2. Find out the state of the TV It is important to know if a TV is in ‘virgin mode’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. If you power on the set and then press the ‘Home’ button on the guest remote, you will see this screen appear, if the TV already has been installed or the wizard was already skipped.
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. This can be done by using the option: Re-install TV set. If PBS is active you can access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button (For the guest remote control, press the following keys in sequence: 3,1,9,7,5,3, ‘MUTE’) , then go to TV Setup, confirm with “OK”.
Press “OK” to access the sub-menu, navigate to “Reinstall TV”. Press “OK” to reinstall the TV set. If all is correct select “YES” and press “OK”. After this operation the TV will power off and on and display the installation wizard. Note: All settings are at default values and no channel plan is available. After reinstalling, the PBS Setup menu will keep the PBS Mode, Room ID and PBS Setup menu and reset all other parameters to default values.
4. Installation wizard When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. Here you will need to select your preferred language. After this, you will need to select the country. Depending on the country selection, some pre-defined settings will be activated, because of local broadcast requirements. Example: digital/analog channels could be disabled; reordering and deleting channels can in some cases not be possible.
The next step is to select ‘Wall mounted’ or ‘On a TV stand’. This option changes some settings for the audio and image of the TV. Now you can select the visual and hearing impaired options. If you select ‘On’, your TV will automatically turn on settings to help visual and hearing impaired people. THE MOST COMMON OPTION IS TO TURN THIS FUNCTION OFF. On the following page we can start the channel installation wizard. You can also press “Back” to correct any previous setting.
For the channel installations, select ‘Install TV channels’ and press ‘OK’ Then you can select ‘Continue’ and press ‘OK’ again. Here you can select the type of channels you would like to install and what preference you will use. It is advisable to check the settings before starting the search.
Note: If all options are disabled you have to go down to the Digital channels option and set the digital channels to ON. A screen is displayed to make changes to set the channel list/map configuration: [Symbol rate mode]: Automatic TV will use the preset Symbol rate (6.900/6.875) Manual Option to set Symbol rate 1 and Symbol rate 2 [Symbol rate 1]: 0.000 (to set) [Symbol rate 2]: 0.
Frequency step size has two options: 1. “1 MHz” – With Full scan, the step size to search for channels is 1 MHz. The scan will take more time but will find also channels broadcasted not according to the channel grid. 2. “8 MHz (default)” – With Full scan, the step size to search for channels is 8 MHz. The scan will be shorter in time but some channels which are not in the expected channel grid (local head-end) will not be found.
During the channel search you can see the progress bar and how many channels are found at that time. When the search is done, you should see “Channel search complete” and a summary of the channels found. In this case: Digital channels found: 53 Analogue channels found: 0 Press the “OK” button on the remote control to finish the search. If you would like to change the picture and sound settings, you can go to “Optimize TV picture and sound” and press the “OK” button on the remote control.
The wizard will ask you some questions about which image you prefer, select the option you desire and press “OK” on the remote control. Once this wizard is done, you will return to the installation menu again. The network wizard will guide you through network setup.
Please select “Next” and press OK to continue The connection will be made to wireless network or via wired network, depending on preferences. TV will automatically acquire an IP address if this is available via DHCP. After the connection is made, the result is shown on the TV. The last option in this menu is “Add your devices”. This can be done if you would like to add a DVD player or STB.
When you are done with this, select “Done” and press ‘OK’ on the remote control. After pressing “Done” you have completed the installation of the TV and you should see this screen. Press “OK” on the remote control to exit this wizard. Note: This wizard will not be available anymore when you start the TV the next time. The only way to re-use this wizard is to reinstall the TV set.
5. Channel options a. Reordering channels For reordering TV channels the channel plan from PBS Setup must be used. In consumer menu you cannot rearrange channels. The PBS Setup can be accessed by using the Yellow remote (RC 22AV8573 Master Remote control) and pressing the MENU Button or with the TV remote press 3,1,9,7,5,3, MUTE). The PBS menu will appear like in picture. Go to the option Channel setup and press “OK” to access the submenu. The channel grid will contain all installed channels.
Navigate to the channel that you want to move and press “OK” on the remote control to select that channel. The arrows around the channel indicate that the channel is selected and can be moved. Use the arrow keys to move the channel to the new position. When you reached the new position press “OK” on the remote control to confirm the new position of the channels. Once you are finished with the reordering, press “Options” on the remote control again.
Press “OK” on the remote control to confirm that you are done with the re-ordering. b. Rename channels Select the channel, press the “Options” button on the remote control and select “Rename” to change name of a channel. If you then press the “OK” button a virtual QWERTY keyboard will pop up. c. Hide channels Important: You cannot delete channels from the channel grid, but you can use the option to hide the channels. Select the Channel, press the “Options” button and select “Hide channels”.
6. Professional Setup [Professional Settings] Select the Setup menu language to be English, French, German or Italian. [Professional Mode] [Off]: The TV operates as a basic (consumer) TV. [On]: All settings in the PBS mode Setup menu are active. Only by switching on this mode the TV will act as a Hospitality TV. [NetTV] [Configure Net TV] allows you to disable/enable the Net TV portal provided by the Philips Net TV server.
[Icon Label] Change the label of the [Browse Portal] icon. [Portal URL] Enter the URL to access from [Browse Portal]. The address is for the SmartUI external server. [Room ID] Entry field to store 4 digits to set the Room Identifier. Room ID can be used to distinguish floors/rooms/setups when using SmartInstall. between different [Switch on volume] When the guest switches the TV on, it will play at the specified volume level. Selectable value from 00 until 60.
[Switch on feature] Starts up in Theme TV, Smart UI or Net TV modes. [Blank Until Feature] The TV will remain black until the Feature is fully loaded. Note: Enabling this option will increase the startup time. [Switch on Picture Format] Switches to a pre-defined picture format. [Display message] [On] To enable the welcome message. [Off] No welcome message [Welcome message line 1 &2] Line 1: First line of the welcome message. Line 2: Second line of the welcome message.
[Local keyboard lock] [Off]: The local keyboard (control buttons on TV) buttons are enabled. [On]: The local keyboard (control buttons on TV) buttons are disabled, power button still enabled. [All]: All local keyboard (control buttons on TV) buttons are disabled. [Remote control lock] [OFF]: All buttons on the guest remote control will function normally. [On]: All buttons on the guest remote control are disabled.
[Browse USB] Enables / disables the USB Browse icon to be presented in the Guest Menu. [Off]: When set to Off, the TV will hide the USB icon in the Home menu. [On]: When set to On, the TV will show the USB icon in the Home menu. [Auto scart] Enables auto scart switching (or break-in) in Professional mode. [AV]: Enables auto scart switching or break-in. [Power On Scart]: Enables auto TV start On/Off when detecting scart break-in.
[SXP Baudrate] Sets the Baud rate for the Serial Express communication channel to be 38200 or 19200 Baud (bits per second). [Enable CI-slot] Enables or disables the use of the integrated CI/CI+ slot: [Off]: No pass through of the TV input signal via the CI-Slot Card is possible; the use of CI Card slot is not possible. [On]: Pass through of the TV input signal via the CI-Slot Card is possible; the use of CI-Card slot is possible. !! Check with your local operator if your CI-Card is compatible with this TV.
[Enable subtitle] Enables or disables the use of subtitles in a DVB broadcast channel: [Off]: No subtitles services available [On]: Subtitles services available [Enable Channel Map] Select Channel Map to be viewed: [Native]: Show standard default channel map [BDS]: To be used only if a system is connected [Source setup] Lists all supported connectors on the TV. A disabled connector will not be visible from the Source menu. [Jointspace] This feature is not supported for hotel mode. Always set it to off.
[Scrambled Program OSD] Show OSD on scrambled TV channel. [Power settings] The possible power settings are explained below. The power on function allows the TV to enter a specific mode ([On], [Standby], or [Last status]) of operation when the mains power is activated (cold start): [On]: The TV will always turn on (show startup channel) after the mains power is connected.
[Delayed reboot] Enables or disables the use of delayed standby: [On]: TV is able to switch on immediately after switching to standby. [Off]: Switch ON time of the TV will be longer after switching to stand-by. [Standby Delay Timeout] This option will set the amount of time for Delayed reboot. 5 mts – TV will power down complete after 5 minutes. 10 mts - TV will power down complete after 10 minutes. [Clock settings] All the clock settings are explained below.
[Time Download] Select the source for the clock time: [Automatic]: Clock time is retrieved from the “Download Program” channel. [Manual]: The clock time is set using the Time Setting option. Note: If the power is disconnected the TV will lose the time set. [Download Country] Set the selected country as the source for clock time. [Download Program] Set selected Download Program as the source for the clock time.
[Reference Time and Date] [Feature settings] Check Feature settings (page 33) [Speaker settings] [TV Speaker Enable] [Off]: The main speakers are muted. The RC can control the volume and mute the headphone/bathroom speaker [On]: The main speakers are active and the behavior of the headphone/bathroom speaker is defined by the Independent Main Speaker Mute. [EasyLink & EasyLink autostart]: only to be used when external audio amplifier supporting HDMI-CEC is connected.
[Headphone] The default volume for headphones can be set. The value define will be applied when the headphones are connected. [Factory default] Restore the factory default of the PBS Menu. Channel installation is not affected. [TV Setup] A shortcut to enter the consumer installation menu. Consumer installation menu should be accessed to change e.g. picture and sound settings and update channels. Using this shortcut will trigger a popup screen which warns losing settings in the PBS menu if you continue.
[Smart Clone] Check Smart Clone section (page 32) [RF Download] Check RF Download section (page 34) [Express Box] Only applicable for system connected installation. After storing PBS settings, the TV will restart to apply the new parameters. Now you can clone all settings to other TV sets by using the option TV to USB and USB to TV. Check how to clone settings (On page 32).
7. Welcome Logo There are 2 Philips logos displayed at startup. The second logo can be replaced by a picture uploaded via USB. File format: 1280 x 720.jpg file. The Welcome Logo is displayed only when Standby mode is set to “Green”. Note: below timing values are approximate indications and can differ from the real situation! Welcome Logo 1. Create graphics file: 1280 x 720 jpg file with the logo. 2. File name: WelcomeLogo.jpg (File name is case-sensitive) 3.
8. Smart Clone Smart Clone With Smart Clone it is possible to copy to/from a USB device TV the configuration data and channel list data. Place a USB Memory stick in the USB side connector of the TV. *The USB device should be formatted as FAT or FAT32. [USB to TV] 1. Select [Smart Clone] and press OK. 2. Select [USB to TV] and press OK. 3. The clone data will be loaded from the USB device into the TV. To activate the loaded settings, wait until the OSD message is displayed to remove the power cord. 4.
9. Feature settings [Multi RC] This function allows that up to four televisions can be installed in a room whereas every TV will listen to its own RC. Once the TV is set, also every RC can be set to remember its connected TV: [Off] Multi RC is turned off; all TVs will listen to a ‘blue’ RC. The TV will listen to a ‘blue’ RC. Press and hold both the menu and blue button on the RC for about five seconds to change the color of the remote. [Green] The TV will listen to a ‘green’ RC.
10. RF Download Instead of using a USB memory device to do cloning and firmware update, this upgrading is also possible using the RF infrastructure. This is supported by SmartInstall (Philips Hospitality RF Download mechanism) and allows a simultaneous upgrade of all installed televisions. [Start Download]: To manually start a RF download action: 1. Select [RF Download] and press OK. 2. Select [Start Download] and press OK.
11. CSM (Consumer Setup menu) The CSM contains data about the TV software, serial number and other details. The menu can be accessed using a standard remote control or using the master remote control. 1. Using the standard remote control: press the following key sequence “1,2,3,6,5,4” 2. Using master remote control (22AV8753D): Press the RECALL button, available only if PBS mode is ON. Notes: Activation of the CSM is only possible if there is no (user) menu on the screen.