Brilliance 241B7 www.philips.
Table of Contents 1. Important �������������������������������������� 1 1.1 Safety precautions and maintenance ��������������������������������� 1 1.2 Notational Descriptions ������������ 3 1.3 Disposal of product and packing material ������������������������������������������ 4 2. Setting up the monitor �������������� 5 2.1 Installation ������������������������������������ 5 2.2 Operating the monitor ���������������7 2.
1. Important • Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics. • Do not block the ventilation holes on the cabinet. • When positioning the monitor, make sure the power plug and outlet are easily accessible. • If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation.
1. Important be better than a 15-minute break every two hours. Try to keep your eyes from eye strain while using the screen for a constant period of time by : not expose the monitor to dust, rain, water, or excessive moisture environment. • If your monitor gets wet, wipe it with dry cloth as soon as possible. • If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord.
1. Important Warning Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “afterimage” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install the base 2. Setting up the monitor 1. 2.1 Installation Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. Package contents Brilliance 241B7 278E9 Quick Start 241B7 2. Hold the stand with both hands. (1) Gently attach the stand to the VESA mount area until the latch locks the stand. Register your product and get support at www.philips.
2.
2. Setting up the monitor Connect to PC 2.2 Operating the monitor 1. Connect the power cord to the back of the monitor firmly. Description of the control buttons 2. Turn off your computer and unplug its power cable. 241B7QPJEB,241B7QPTEB: 3. Connect the monitor signal cable to the video connector on the back of your computer. 4. Plug the power cord of your computer and your monitor into a nearby outlet. 5. Turn on your computer and monitor. If the monitor displays an image, installation is complete.
2. Setting up the monitor 241B7QPJKEB: Description of the On Screen Display 8 9 10 What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window.
2. Setting up the monitor The OSD Menu Resolution notification Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. Main menu PowerSensor This monitor is designed for optimal performance at its native resolution, 1920 × 1080 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920 × 1080 @ 60 Hz for best results.
2.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1. Extend the monitor base to its maximum height. 100mm 100mm 2. Place the monitor face down on a smooth surface.
3. Image Optimization How to enable SmartImage? 3. Image Optimization 3.1 SmartImage What is it? SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage delivers great optimized monitor performance. 1. Press to launch the SmartImage on screen display. 2.
3. Image Optimization files, scanned articles or other general office applications. • Photo: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors.
4. PowerSensor™ 4. PowerSensor™ • • • • How does it work? PowerSensor works on principle of transmission and reception of harmless “infrared” signals in order to detect user-presence. When the user is in front of the monitor, the monitor operates normally, at the predetermined settings that the user has set- i.e.
4. PowerSensor™ Note A manually selected PowerSensor mode will remain operational unless and until it is readjusted or the default mode is recalled. If you find that the PowerSensor is excessively sensitive to nearby motion for some reason, please adjust to a lower signal strength. Keep sensor lens clean, if the sensor lens is dirty, wipe it with alcohol to avoid reducing of distance detection .
5.Built-in Webcam with Microphone 5.1 PC system requirements 5. Built-in Webcam with Microphone • Operating system : Microsoft Windows 7, Microsoft Windows Vista, Microsoft Windows XP (SP2), and any other OS whichever support UVC/UAC (USB Video Class compliant / Audio Class compliant) under USB 2.0 standard • Processor: 1.6GHz or above • RAM: 512MB (for XP) / 1GB(for Vista and Windows7) • Hard disk space: minimum 200MB • USB: USB 2.
5.Built-in Webcam with Microphone 5.2 Using the device Note To set up a video call, you must have a reliable Internet connection, an ISP, and software like Internet messenger or video phone call program. Make sure the person that you are calling has compatible video-calling software. The video and audio performance quality depends on the bandwidth available on both ends. The person you are calling must have similar capability of devices and software.
6.Daisy-chain function Note 1. Depending on the capabilities of your graphic cards, you should be able to daisy chain multiple displays with various configurations. Your display configurations will depend on your graphic card capabilities. Please check with your graphic card vendor and always update your graphic card driver. 6. Daisy-chain function (Available for 241B7QPTEB) Daisy-chain enables multiple monitor connections This Philips display is equipped with DisplayPort 1.
6.Daisy-chain function Display Resolution (standard 60 Hz) DisplayPort Default 1680 x 1050 1920 x 1080 (1080p) or 1920 x 1200 2560 x 1600(WQXGA) 3840 x 2160(Ultra HD, 4K) or 4096 x2160 (4K x 2K) DisplayPort1.1 DisplayPort1.1 Maximum number of display chaining(including 1st motherboard connection display) Clone mode (DP1.1 Extend mode (DP1.2) or DP1.2) 5 5 4 4 DisplayPort1.1 DisplayPort1.
7.Technical Specifications 7. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch Contrast Ratio (typ.) Optimum Resolution Viewing Angle Display Colors Flicker Free Picture Enhancement Vertical Refresh Rate Horizontal Frequency sRGB LowBlue Mode Connectivity Signal Input/Output USB Input Signal Audio In/Out Convenience Built-in speaker Built-in webcam IPS Technology LED 23.8" W (60.4 cm) 16:9 0.275(H) mm x 0.
7.Technical Specifications Power(241B7QPJEB/241B7QPJKEB) AC Input AC Input AC Input Consumption Voltage at Voltage at Voltage at 100VAC , 60Hz 115VAC , 60Hz 230VAC, 50Hz Normal Operation 19.94W (typ.) 19.32W (typ.) 19.14W (typ.) Sleep (Standby) <0.3W <0.3W <0.3W Off <0.3W <0.3W <0.3W Off (AC switch) 0W 0W 0W AC Input AC Input AC Input Heat Dissipation* Voltage at Voltage at Voltage at 100VAC , 60Hz 115VAC , 60Hz 230VAC, 50Hz 68.05 BTU/hr 65.94 BTU/hr 65.32 BTU/hr Normal Operation (typ.) (typ.) (typ.
7.
7.Technical Specifications Note 7.1 Resolution & Preset Modes 1. EPEAT rating is valid only where Philips registers the product. Please visit www.epeat.net for registration status in your country. Maximum Resolution 1920 x 1080 @ 60 Hz (analog input) 1920 x 1080 @ 60 Hz (digital input) Recommended Resolution 2. This data is subject to change without notice. Go to www.philips. com/support to download the latest version of leaflet. 1920 x 1080 @ 60 Hz (digital input) H. freq (kHz) 3.
8.Power Management 8. Power Management The following setup is used to measure power consumption on this monitor. If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
9.Customer care and warranty of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 9. Customer care and warranty 9.
9.Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
9.Customer care and warranty Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT Monitor panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
9.Customer care and warranty 9.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center. For Warranty Period please refer to Warranty Statement in Important Information Manual.
10.Troubleshooting & FAQs 10. Troubleshooting & FAQs • Check to see if the monitor cable has bent pins. • Make sure the computer is turned on. 10.1 Troubleshooting AUTO button doesn't function • This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. The auto function is applicable only in VGA-Analog mode.
10.Troubleshooting & FAQs Main Controls. It is valid only in VGA mode. and cannot be repaired. The damage mentioned above is not covered under your warranty. Horizontal flicker appears Image appears distorted. Text is fuzzy or blurred. • • Adjust the image using the “Auto” function in OSD Main Controls. • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
10.Troubleshooting & FAQs you for monitor drivers (.inf and .icm files) or a driver disk when you first install your monitor. Follow the instructions to insert the companion CD-ROM included in this package. Monitor drivers (.inf and .icm files) will be installed automatically. 10.2 General FAQs Q1: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? Ans.: Recommended resolution for this monitor: 1920 x 1080 @ 60 Hz.
10.Troubleshooting & FAQs Ans.: Yes, you can change your color setting through OSD control as the following procedures, • Press "OK" to show the OSD (On Screen Display) menu • Press "Down Arrow" to select the option "Color" then press "OK" to enter color setting, there are three settings as below. 1. Color Temperature: The six settings are 5000K, 6500K, 7500K, 8200K, 9300K and 11500K.
10.Troubleshooting & FAQs Ans.: Your LCD monitor works best at its native resolution of 1920 x 1080 @ 60 Hz. For best display, please use this resolution. Q13: How to unlock/lock my hot key? Ans.: Please press for 10 seconds to unlock/lock the hot key, by doing so, your monitor pops out “Attention” to show the unlock/lock status as shown below illustrators.
2019 © TOP Victory Investment Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
