Specifications

Alignments
EN 64 L05.1U AA8.
Table 8-3 Option code overview per model (OP6)
Option bit definition
Option Byte 1 (OP1)
• OB17: PHILIPS TUNER
– 0 : ALPS / MASCO compatible tuner is in use.
– 1 : Philips compatible tuner is in use.
Option Byte 2 (OP2)
• OB26: GREEN UI
– 0 : Green UI is disabled (for Philips brand).
– 1 : Green UI is enabled (for Magnavox brand).
– Note: only for NAFTA region.
• OB23: TILT
– 0 : Rotate Picture is disabled or not applicable.
– 1 : Rotate Picture is enabled.
• OB22: FINE TUNING
– 0 : Fine Tuning for Channel Offset is disabled or not
applicable.
– 1 : Fine Tuning for Channel Offset is enabled.
Option Byte 3 (OP3)
• OB36: ATI_PIP
– 0 : PIP feature is disabled
– 1 : PIP feature is enabled
• OB33: VIRTUAL DOLBY
– 0 : Virtual Dolby is not applicable.
– 1 : Virtual Dolby is applicable.
• OB32: WIDE SCREEN
– 0 : Software is used for 4:3 sets or not applicable.
– 1 : Software is used for 16:9 sets.
Option Byte 4 (OP4)
This option byte is not used.
Option Byte 5 (OP5)
• OB57: AV1
– 0 : AV1 source is not present.
– 1 : AV1 source is present.
• OB56: AV2
– 0 : AV2 source is not present.
– 1 : AV2 source is present.
– Note : For EU, when AV2=“1”, both EXT2 and SVHS2
should be included in the OSD loop.
• OB55: AV3
– 0 : Side/Front AV3 source is not present.
– 1 : Side/Front AV3 source is present.
• OB54: CVI
– 0 : CVI source is not available.
– 1 : CVI source is available.
• OB53: SVHS2
– 0 : SVHS2 source is not available.
– 1 : SVHS2 source is available.
– Note : This option bit is not applicable for EU.
• OB52: SVHS3
– 0 : SVHS3 source is not available.
– 1 : SVHS3 source is available.
– Note : This option bit is not applicable for EU.
• OB51: HDMI
– 0 : HDMI source is not present.
– 1 : HDMI source is present.
• OB50: YPbPr
– 0: YPbPr source is not present.
– 1: YPbPr source is present.
Option Byte 6 (OP6)
• OB67: QUADRA_SURF
– 0 : Quadra Surf feature is disabled or not applicable.
– 1 : Quadra Surf feature is enabled.
• OB66: OP_SMART_SURF
– 0 : Smart Surf key is not used on remote control.
– 1 : Smart Surf key is used on remote control.
• OB64: COMBFILTER
– 0 : 3D-combfilter is not present.
– 1 : 3D-combfilter is present.
• OB63: ACTIVE CONTROL
– 0 : Active Control feature is disabled or not applicable.
– 1 : Active Control feature is enabled.
Note: Quadra Surf option is only applicable for Philips branded
sets.
Option Byte 7 (OP7)
• OB73: Digital Module Reset Control
– 0: Reset control is not used.
– 1: Reset control is used.
8.3.2 Tuner
Note: Described alignments are only necessary when the NVM
(item 7601) is replaced.
IF PLL
This adjustment is auto-aligned. Therefore, no action is
required.
AGC (AGC take over point)
1. Set the external pattern generator to a color bar video
signal and connect the RF output to aerial input. Set
amplitude to 10 mV and set frequency to 61.25 MHz
(channel 3).
2. Connect a DC multimeter to pin 1 of the tuner (item 1000
on the main panel).
3. Activate the SAM.
4. Go to the TUNER sub menu.
5. Select AGC with the UP/DOWN cursor keys.
6. Adjust the AGC-value with the LEFT/ RIGHT cursor keys
until the voltage at pin 1 of the tuner lies between 3.8 and
2.3 V (default value is “20”).
7. Switch the set to STANDBY, in order to store the
alignments.
CL (Cathode drive level)
Always set to “5”.
8.3.3 White Tone
In the WHITE TONE sub menu, the values of the black cut off
level can be adjusted. Normally, no alignment is needed, and
you can use the given default values.
The color temperature mode (NORMAL, COOL and WARM)
and the color (R, G, and B) can be selected with the UP/DOWN
RIGHT/LEFT cursor keys. The value can be changed with the
LEFT/RIGHT cursor keys. First, select the values for the
NORMAL color temperature. Then select the values for the
COOL and WARM mode. After alignment, switch the set to
STANDBY, in order to store the alignments.
Option Bit Option Name 26PW21718 30PW21709 27PT21714 32PT21705
OP6
7 Not Used 0000
6 Not Used 0000
5 Not Used 0000
4 Not Used 0000
3 Digital_Module_Reset_Control 1 1 1 1
2 Not Used 0000
1 Not Used 0000
0 Not Used 0000
OP7 value (dec) 0 0 0 0