V line 273V7 www.philips.
Table of Contents 1. Important........................................ 1 1.1 Safety precautions and maintenance................................... 1 1.2 Notational Descriptions.............. 3 1.3 Disposal of product and packing material............................................ 4 2. Setting up the monitor................ 5 2.1 Installation...................................... 5 2.2 Operating the monitor................. 8 2.3 Remove the Base Assembly for VESA Mounting ...........................
1. Important discoloration and damage to the monitor. 1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user's manual before you use your monitor. It contains important information and notes regarding the operation of your monitor.
1. Important • Gently closing and rolling your eyes to relax. • Reposition your screen to appropriate height and angle according to your height. • Adjusting the brightness and contrast to appropriate level. • Adjusting the environment lighting similar to that of your screen brightness, avoid the fluorescent lighting, and surfaces that don't reflect too much light. • • Do not store or use the monitor in locations exposed to heat, direct sunlight or extreme cold.
1. Important service center. (please refer to the chapter of “Consumer Information Center”) • For transportation information, please refer to “Technical Specifications”. • Do not leave your monitor in a car/ trunk under direct sun light. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document. Notes, Cautions and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install base stand 2. Setting up the monitor 1. Place the monitor face down on soft and smooth surface taking care to avoid scratching or damaging the screen. 2.1 Installation Package contents 2. Attach/Slide the base column with the monitor until it clicks into position. V line 273V7 Quick Start Register your product and get support at www.philips.
2.
2. Setting up the monitor Connect to PC 1. Connect the power cord to the back of the monitor firmly. 2. Turn off your computer and unplug its power cable. 3. Connect the monitor signal cable to the video connector on the back of your computer. 4. Plug the power cord of your computer and your monitor into a nearby outlet. 5. Turn on your computer and monitor. If the monitor displays an image, installation is complete.
2. Setting up the monitor 273V7QDA, 273V7QJA 2.2 Operating the monitor Front view product description 273V7QS, 273V7QDS 3 3 7 6 5 7 4 6 5 4 2 Switch monitor’s power ON and OFF. 2 Access the OSD menu. Confirm the OSD adjustment. Switch monitor’s power ON and OFF. Adjust the OSD menu. Access the OSD menu. Confirm the OSD adjustment. Adjust the speaker volume. Change the signal input source. Adjust the OSD menu. Adjust the brightness level. Return to previous OSD level.
2. Setting up the monitor Description of the On Screen Display What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window.
2. Setting up the monitor The OSD Menu Main menu LowBlue Mode Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. Sub menu On 1, 2, 3 Off Input VGA DVI (273V7QS, 273V7QD) HDMI (273V7QD) HDMI 1.
2. Setting up the monitor Resolution notification This monitor is designed for optimal performance at its native resolution, 1920 × 1080 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920 × 1080 @ 60 Hz for best results. Display of the native resolution alert can be switched off from Setup in the OSD (On Screen Display) menu.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 2.3 Remove the Base Assembly for VESA Mounting Remove the Base Stand Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1. Place the monitor face down on a smooth surface, taking care to avoid scratching or damaging the screen. 100mm 100mm 2.
3. Image Optimization 3. Image Optimization 1. 3.1 SmartImage 2. Keep pressing to toggle among EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode and Off. What is it? SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage delivers great optimized monitor performance.
3. Image Optimization • Photo: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors. • Movie: Ramped up luminance, deepened color saturation, dynamic contrast and razor sharpness displays every details in darker areas of your videos without color washout in brighter areas maintaining a dynamic natural values for the ultimate video display.
4. Technical Specifications 4. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch SmartContrast Response Time (typ.) Smart Response (typ.) (273V7QD, 273V7QJ) Optimum Resolution Viewing Angle (typ.) Picture Enhancement Display Colors Vertical Refresh Rate Horizontal Frequency sRGB Flicker Free LowBlue Mode Connectivity Signal Input Input Signal Audio in/out Convenience Built-in speakers(typ.
4. Technical Specifications Stand Tilt -5 / +20 Power (273V7QS, 273V7QD) AC Input Voltage AC Input Voltage AC Input Voltage Consumption at 100VAC, 50Hz at 115VAC, 50Hz at 230VAC, 50Hz Normal Operation 26.07 W (typ.) 25.99 W (typ.) 25.70 W (typ.) Sleep(Standby) <0.5 W <0.5 W <0.5 W Off <0.5 W <0.5 W <0.5 W AC Input Voltage AC Input Voltage AC Input Voltage Heat Dissipation* at 100VAC, 50Hz at 115VAC, 50Hz at 230VAC, 50Hz Normal Operation 88.98 BTU/hr(typ.) 88.74 BTU/hr(typ.) 85.56 BTU/hr(typ.
4. Technical Specifications Product without stand Product with packaging Operating Condition Temperature range (operation) Relative humidity (operation) Atmospheric pressure (operation) Temperature range (Non-operation) Relative humidity (Non-operation) Atmospheric pressure (Non-operation) 3.94 kg (273V7QS) 3.96 kg (273V7QDS) 4.04 kg (273V7QDA) 4.10 kg (273V7QJA) 6.21 kg (273V7QS) 6.34 kg (273V7QDS) 6.47 kg (273V7QDA) 6.
4. Technical Specifications 4.1 Resolution & Preset Modes Maximum Resolution 1920x1080@60Hz (analog input) 1920x1080@60Hz (digital input) Recommended Resolution 1920x1080@60Hz (analog input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 35.16 800 x 600 56.25 37.88 800 x 600 60.32 48.08 800 x 600 72.19 46.88 800 x 600 75.00 47.73 832 x 624 74.55 48.36 1024 x 768 60.00 56.
5. Power Management 5. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
6. Customer care and warranty of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 6. Customer care and warranty 6.
6. Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
6. Customer care and warranty 1.
6. Customer care and warranty 6.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center.
7. Troubleshooting & FAQs 7. Troubleshooting & FAQs • Check to see if the monitor cable has bent pins. • Make sure the computer is turned on. 7.1 Troubleshooting AUTO button doesn't function • This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. The auto function is applicable only in VGA-Analog mode.
7. Troubleshooting & FAQs7 Image appears distorted. Text is fuzzy or blurred. Main Controls. It is valid only in VGA mode. Horizontal flicker appears • • Adjust the image using the “Auto” function in OSD Main Controls. Green, red, blue, dark, and white dots appears on the screen • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode. • • You can adjust “power on” light using the power LED Setup in OSD main Controls.
7. Troubleshooting & FAQs • Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1920 x 1080 @ 60 Hz. • Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor. • monitor, make sure that there is no pressure or force applied to the panel surface side. This may affect your warranty conditions. Q7: How should I clean the LCD surface? Ans.: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol.
7. Troubleshooting & FAQs7 as 2004K are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K. Warning Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “afterimage” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. Q9: Can I connect my LCD monitor to any PC, workstation or Mac? Ans.: Yes.
© 2018 Koninklijke Philips N.V. All rights reserved. This product was manufactured and brought to the market by or on behalf of Top Victory Investments Ltd. or one of its affiliates. Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. used under license. Specifications are subject to change without notice.
