Manual file:///D|/My%20Documents/dfu/300WN5/english/300wn5/MANUAL.
Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Installation Locations • FAQs • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.
Safety & Troubleshooting Consult a service technician if the monitor does not operate normally when the operating instructions given in this manual have been followed. RETURN TO TOP OF THE PAGE Installation Locations ● ● ● ● ● ● Avoid exposure to heat and extreme cold Do not store or use the product in locations exposed to heat, direct sunlight or extreme cold. Avoid moving the product between locations with large temperature differences.
About This Manual About This Manual About This Guide • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor TV. It describes the features, setup, operation and other important information. It includes the following sections: ● ● ● ● ● ● ● ● Safety and Troubleshooting Information provides tips and solutions for common problems as well as other related information you may need.
About This Manual Notes, Cautions and Warnings Throughout this guide blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions or warnings. They are used as follows: NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data.
Product Information Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Product Features 300WN5 ● ● ● ● ● ● ● ● ● ● ● ● 29.
Product Information • Pixel Pitch 0.5025 x 0.5025 mm • LCD Panel type 1280 x 768 pixels R.G.B. vertical stripe Hard coating surface, anti-glare polarizer • Effective viewing area (H) 643.2 x (V) 385.92mm • Display Colors 8 bits interface (16.7M colors) PC SCANNING • Vertical refresh rate 58Hz-60Hz • Horizontal frequency 31kHz-49kHz PC VIDEO • Video dot rate < 80 MHz • Input impedance - Video 75 ohm - Sync 2.2K ohm • Input signal levels 0.
Product Information • Contrast ratio 800:1 (typ.) • Brightness 600 cd/m2 (typ.) • Peak contrast angle 6 o'clock • White Chromaticity x: 0.283 y: 0.297 (at 9300°K) x: 0.313 y: 0.329 (at 6500°K) x: 0.328 y: 0.344 (at 5700°K) • Viewing Angle (C/R >5) Upper >85° (typ.) Lower >85° (typ.) Left >85° (typ.) Right >85° (typ.) • Response time <=16ms (typ.) sRGB sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.
Product Information 10 factory preset modes: Resolution Mode H. freq (kHz) V. freq (Hz) 640*480 VGA VESA 60 31.469 59.940 800*600 SVGA VESA 60 37.879 60.317 1024*768 XGA VESA 60 48.363 60.004 1280*768 GTF 60 47.700 60.000 EDTV 480P 31.470 60.000 SDTV 480i 15.734 59.940 EDTV 576P 31.250 50.000 SDTV 576i 15.625 50.000 HDTV 1080i 33.750 60.000 HDTV 720P 45.000 60.
Product Information OFF Blanked No No < 5W Amber AC OFF Blanked No No < 2W Off This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimension (WxHxD) * 867.7mm x 505mm x 183mm (incl. Pedestal, Speakers) 726.7mm x 469.3mm x 115mm (w/o Pedestal, Speakers) • Weight 16.0 kg (incl. Pedestal, Speakers) 14.
Product Information 1. The digital only connector contains 24 signal contacts organized in three rows of eight contacts. Signal pin assignments are listed in the following table: Pin Signal No. Assignment Pin Signal No. Assignment Pin Signal No. Assignment 1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ 3 T.M.D.S.
Product Information 2 Green video input 10 Cable detect 3 Blue video input 11 4 Ground 12 Serial data line (SDA) 5 NC 13 H. Sync / H+V 6 Red video ground 14 V. Sync 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground Identical output, connected to pin 10 3. RS232 Connector D-sub 9-pin male connector for communication with plasma engine or PC. Pin No.
Product Information Pin No. Signal Pin No. 1 Audio right channel output (0.5 Vrms, < 1K ohms) 2 2 Audio right channel input (0.5 Vrms, > 10K ohms) 1 3 Audio left channel output (0.5 Vrms, < 1K ohms) 6 4 Audio ground 4 5 Blue signal ground 5 6 Audio left channel input (0.5 Vrms, > 10K ohms) 3 7 Blue signal I/O (0.7 Vp-p, 75 ohms) 7 8 Function switching I/O (L: < 2V, H: > 10V, 10K ohms) 8 9 Green signal ground 9 10 Intercommunication data line No.
Product Information 19 Composite video signal output (1 Vp-p, 75 ohms, sync: negative) 20 20 Composite video signal input (1 Vp-p, 75 ohms, sync: negative) 19 21 Plug shield (common ground) 21 RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components. Product Description RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/300WN5/english/300wn5/PRODUCT/PRODUCT.
Installing your LCD Monitor/TV Installing your LCD Monitor/TV Product Description • Connecting to Your PC, TV antenna, DVD/VCR etc.
Installing your LCD Monitor/TV Rear View TV version 1 AC IN AC power in 2 AC Power AC power switch 3 D-Sub PC analog D-Sub input 4 PC - Audio PC Stereo input 5 DVI-D PC digital input 6 RS232 RS232 network connection 7 External/ EURO-AV SCART connection (for Europe only) 8 Composite Video Output Composite video CVBS ouput file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/INSTALL.
Installing your LCD Monitor/TV 9 10 11 Audio (L) Output Audio (L) output Audio (R) Output Audio (R) output Audio (L) Output Audio (L) output for the detachable speaker (L) Audio (R) Output Audio (R) output for the detachable speaker (R) Line out Audio output for external speakers RETURN TO TOP OF THE PAGE Audio/Video version 1 AC IN AC power in 2 AC Power AC power switch 3 D-Sub PC analog D-Sub input file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/INSTALL.
Installing your LCD Monitor/TV 4 PC - Audio PC Stereo input 5 DVI-D PC digital input 6 RS232 RS232 network connection 7 External/ EURO-AV SCART connection (for Europe only) 8 Audio (L) Output Audio (L) output for the detachable speaker (L) Audio (R) Output Audio (R) output for the detachable speaker (R) Line out Audio output for external speakers 9 RETURN TO TOP OF THE PAGE Monitor version 1 AC IN AC power in file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/INSTALL.
Installing your LCD Monitor/TV 2 AC Power AC power switch 3 D-Sub PC analog D-Sub input 4 PC - Audio PC Stereo input 5 DVI-D PC digital input 6 RS232 RS232 network connection 7 Audio (L) Output Audio (L) output for the detachable speaker (L) Audio (R) Output Audio (R) output for the detachable speaker (R) Line out Audio output for external speakers 8 RETURN TO TOP OF THE PAGE Side View (Right) TV version file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/INSTALL.
Installing your LCD Monitor/TV 1 Audio (L) Audio (L) for component video 2 Audio (R) Audio (R) for component video 3 Component Video Component video Y/Pb/Pr input 4 Composite Video Composite video CVBS input 5 Audio (L) Audio (L) for CVBS and S-Video 6 Audio (R) Audio (R) for CVBS and S-Video 7 S-Video S-Video input 8 RF 75 TV Antenna or CATV cable in RETURN TO TOP OF THE PAGE Audio/Video version file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/INSTALL.
Installing your LCD Monitor/TV 1 Audio (L) Audio (L) for component video 2 Audio (R) Audio (R) for component video 3 Component Video Component video Y/Pb/Pr input 4 Composite Video Composite video CVBS input 5 Audio (L) Audio (L) for CVBS and S-Video 6 Audio (R) Audio (R) for CVBS and S-Video 7 S-Video S-Video input RETURN TO TOP OF THE PAGE Optimising Performance ● For best performance, ensure that your display settings are set at 1280x768, 60Hz.
Installing your LCD Monitor/TV Note: You can check the current display settings by pressing the 'MENU' button once. ● You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance out of your monitor. This is included on this CD. Step-by-step instructions are provided to guide you through the installation process. Click on the link to find out more about this program. More about FP_setup04.
On Screen Display On Screen Display On Screen Display Control • Using Your Remote Control On Screen Display Controls An overall view of the On-Screen Display (OSD) structure is shown below. You can use it as a reference for further adjusting your Monitor/TV. There are three different modes of OSD available for different models: ● ● ● PC Mode Audio/Video Mode TV Mode PC Mode A Main Menu B Sub-Menu name C Menu icon 1. With the menu off, push the MENU button to enter OSD system and display the main menu.
On Screen Display 2. Push the and buttons to move between the function icons. As you move from one icon to another, the function name will be highlighted. 3. Push the MENU button once to activate the highlighted function. Push / to select the preferred parameter, push the button to enter the selected one, then use the buttons making your changes. 4. Push the button to return the main menu or select another function. .
On Screen Display The Brightness function : Push the button to increase luminance; push the button to decrease luminance (min 0 ~ max. 100). The Contrast function : BRIGHTNESS/ CONTRAST Push the button to increase the contrast; push the button to decrease the contrast (min 0 ~ max. 100). The Light Sensor function: buttons to toggle Light Sensor function. Push the This function automatically finetunes the brightness of the monitor according to the environment. Select your preferred function.
On Screen Display SURROUND: ON/OFF MUTE: ON/OFF AUDIO AUDIO SOURCE: Only in PC TV/VIDEO mode POWER SAVING:ON/OFF Positioning moves the viewing area around on the monitor screen. EXIT: Exit this menu H.POSITION /V.POSITION: When making changes to either the 'Horizontal' or 'Vertical' settings, the image will simply be shifted in response to your selection/change. Minimum is '0' ( ). Maximum is '100' ( ).
On Screen Display NOTE: 1. When operating in DVI mode, the positioning adjustments are not available. 2. The 4:3 Aspect Ratio and Full Screen items are not available in WXGA 1280x768 modes. To adjust the image settings. EXIT: Exit this menu AUTO ADJUST:Press to select automatic adjustment . PHASE :Use the and PIXEL CLOCK:Use the buttons to adjust from 0 to 100. and buttons to adjust from 0 to 100. IMAGING SETTINGS file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display Note: Operating in DVI mode, the Pixel Clock and Phase adjustments are not available. Color Settings adjusts the color temperature. EXIT: Exit this menu NATURE COLOR: Equivalent to original panel color. NORMAL COLOR: 6500K (Same as sRGB) default from FACTORY BLUE PRESET: Equivalent to 9300K RED PRESET: Equivalent to 5700K USER PRESET: Adjust red, green, blue three colors from 0 to 100. COLOR SETTINGS file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display Each time the OSD opens, it displays in the same location on the screen. 'OSD Settings' (horizontal/vertical) provides control over this location. EXIT: Exit this menu HORIZONTAL: Adjustable from 0 to 100. VERTICAL: Adjustable from 0 to 100. OSD HOLD TIME: The OSD stays active for as long as it is in use. The range of time setting is from 5 to 60 seconds. OSD SETTINGS OSD LOCK: Controls user access to adjustments. Show key icon after selecting lock.
On Screen Display Note: When the OSD is locked, press menu button on the monitor, and the OSD LOCK menu will appear. Press (+) to unlock and allow user access to all applicable settings. Language sets the OSD to display in one of the five or six languages provided. That is, English, Spanish, French, German, Italian (not available in NAFTA model) and Simplified Chinese (China models only). LANGUAGE file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display Reset the settings to the factory default values. EXIT: Exit this menu POSITION SETTINGS ONLY: Resume position setting to factory default. COLOR SETTINGS ONLY: Resume color setting to factory default. FACTORY RESET All SETTINGS: Load all factory default settings. Adjust picture in picture preferences. SIZE: Turn off and set the size of PIP. Users can chose your preferred size. ● ● ● ● OFF SMALL MEDIUM LARGE H POSITION: Adjust the Horizontal position of PIP.
On Screen Display RETURN TO TOP OF THE PAGE Audio/Video Mode Exit from this menu. EXIT file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display Use up and down arrow button to highlight the "INPUT SELECT". Select video source for main display: ● ● ● ● ● ● ● PC ANALOG: PC VGA input PC DIGITAL: PC DIGITAL input TV TUNER: Antenna or cable TV input EXT: Scart input COMPOSITE: Composite video input S-VIDEO: S-video input COMPONENT: Component video input INPUT SELECT Adjust picture characteristics to suit personal preference.
On Screen Display COLOR TEMP: Select from Normal, Cool or Warm by "-" and "+" buttons. PICTURE NOTE: 1. "TINT" is not available in component input in all models. 2. "TINT" is available in NAFTA model only. 3. "HOR SHIFT" only function in component input. Adjust audio characteristics to suit personal preference. EXIT: Exit from this menu.
On Screen Display Set language for OSD. There are 6 languages of OSD display. ● ENGLISH ● ● ● ● DEUTSCH ITALIANO ● LANGUAGE NOTE: In AP/China models, Simplified Chinese is supported. file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display Activate special control features: EXIT: Exit from this menu. SLEEP TIMER: Slide bar to select off/15/30/60/90/120/150/180. OSD LOCK: Show key icon after selecting lock. LIGHT SENSOR: Push the buttons to toggle Light Sensor function. VIDEO MODE: Set the screen scaling mode to suit personal preference: ● SPECIAL FEATURES ● ● ● STANDARD MODE 4:3 FULL SCREEN NONLINEAR SCALING 1) When users first enter the PARENTAL CONTROLS, the screen will show the window asking user key in the code.
On Screen Display 2) Users will see the window "Access code" when they enter this function. ● ● ● ● EXIT LOCK CHANGE CODE CLEAR ALL PARENTAL CONTROLS 3) Enter Master code "0711" twice or the code entered in step 1. Reset the setting to default values. NO: Keep the setting as current. YES: Load factory setting FACTORY RESET file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display RETURN TO TOP OF THE PAGE TV Mode Exit from this menu EXIT Select video source for main display: ● ● ● ● ● ● ● PC ANALOG: PC VGA input PC DIGITAL: PC DIGITAL input TV TUNER: Antenna or cable TV input EXT: Scart input COMPOSITE: Composite video input S-VIDEO: S-video input COMPONENT: Component video input INPUT SELECT file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display Adjust picture characteristics to suit personal preference. EXIT: Exit from this menu BRIGHTNESS: Adjustable from 0 to 100 CONTRAST: Adjustable from 0 to 100 COLOR: Adjustable from 0 to 100 SHARPNESS: Adjustable from 0 to 100 TINT: Not available in component input. Adjustable from 0 to 100 COLOR TEMP: Select from Normal, Cool or Warm by "-" and "+" buttons. PICTURE NOTE: 1. "TINT" is not available in component input in all models. 2. "TINT" is available in NAFTA model only.
On Screen Display Adjust audio characteristics to suit personal preference. EXIT: Exit from this menu. TREBLE: Adjustable from 0 to 100 BASS: Adjustable from 0 to 100 BALANCE: Adjustable from 0 to 100 VOLUME: Adjustable from 0 to 100 SURROUND: Switch Surround Sound On/ Off AUDIO MUTE: Switch Mute On/ Off Set language for OSD. There are 6 languages of OSD display. ● ENGLISH ● ● ● ● DEUTSCH ITALIANO ● LANGUAGE file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display Note: In AP/China models, Simplified Chinese is supported. Activate special control features: EXIT: Exit from this menu. SLEEP TIMER: Slide bar to select off/15/30/60/90/120/150/180. OSD LOCK: Show key icon after selecting lock. LIGHT SENSOR: Push the function.
On Screen Display 1) When users first enter the PARENTAL CONTROL, the screen will show the window asking user key in the code. 2) Users will see the window" Access code" when they enter this foundation. ● ● PARENTAL CONTROLS ● ● EXIT LOCK CHANGE CODE CLEAR ALL file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display 3) Enter Master code "0711" twice or the code entered in step 1. SYSTEM: NOTE: The SYSTEM item is only available in Western Europe model. CHANNEL SEARCH: SETUP file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display MANUAL STORE: CHANNEL SKIP: CHANNEL SWAP: Reset the setting to default values. NO: Keep the setting as current. YES: Load factory setting FACTORY RESET RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
On Screen Display file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/osddesc.
Remote Control Remote Control On Screen Display • Using Your Remote Control Using Your Remote Control For Europe and most of Asia Pacific countries For Europe and most of Asia Pacific countries Remote Control Diagram file:///D|/My%20Documents/dfu/300WN5/english/300wn5/OSD/tv_control.
Remote Control 1 Standby To set the TV temporarily to standby mode. To switch on the TV set, press Programme button (p -, +), any digit between 0 and 9 or AV source button (The amber light indicates when set is in standby mode) ● To select TV/Video sources in PIP mode and TV mode If using TV 'STANDBY', press this button to return to 'ON' 2 AV source 3 Surround sound ON/ OFF Turn on/off virtual surround sound.
Remote Control 5 PIP Shift To change 'Picture in Picture' window position in PC mode 6 Mute To disable sound. To restore sound, press button again. 1. Volume level up/down 7 Volume/Cursor control 8 Menu To turn on or off the OSD (On-Screen Display). To select function in OSD. 9 Smart sound controls To access a series of settings: VOICE, MUSIC, THEATRE and PERSONAL 2.
Remote Control ● 19 Sound mode ● To switch from STEREO to MONO or to choose between Dual I and Dual II for bilingual transmissions. For TV sets fitted with NICAM reception, depending on the transmission, you can switch from NICAM STEREO to MONO or choose between NICAM DUAL I, NICAM DUAL II and MONO. If using Teletext, press this button to display dual pages on screen. 20 TXT Enlarge Enlarge teletext context to two times larger. 21 TXT Reveal Reveal or conceal hidden content in teletext.
Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Slovakia • Slovenia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay •
Download and Print Download and Print Installing your LCD monitor driver • Download and Printing Instructions • Installing FPadjust Program Installing Your LCD monitor driver System requirements: ● ● PC running Windows® 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP or later Find your driver ".inf/.icm/.cat" at : /PC/drivers/ Read the "Driver_install02.txt" file before installing. This page provides an option to read the manual in .pdf format.
Download and Print 2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to Disk'. 3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or 'source', choose 'source'). Printing instructions: To print the manual: 1. With the manual file open, follow your printer's instructions and print the pages you need.
Download and Print Download FP_setup04.exe ● ● ● From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to Disk'. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or 'source', choose 'source'). Exit your browser and install the FPadjust Program. Read the "FP_Readme04.txt" file before installing. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/300WN5/english/download/download.
FAQs (Frequently Asked Questions) FAQs (Frequently Asked Questions) Safety and Troubleshooting • General FAQs • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information General FAQs Q: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? A: Recommended video mode is 1280x768 @60Hz. 1.
FAQs (Frequently Asked Questions) Q: How do I adjust the resolution? A: Your video card/graphic driver and monitor together determine the available resolutions. You can select the desired resolution under the Control Panel of Windows® 95/98, Me, 2000 or XP, and with the 'Display properties/Settings'. Q: What if I get lost while I am making monitor adjustments? A: Simply press the MENU button, then select 'Factory Reset/All Settings' to recall all of the original factory settings.
FAQs (Frequently Asked Questions) A: A protective coating is applied to the surface of the LCD, which is durable to a certain extent (up to 3H in this Philips 30" LCD monitor). In general, it is recommended that the panel surface is not subjected to any excessive shocks or scratches. An optional protective cover with greater scratch resistance is also available. Q: How should I clean the LCD surface? A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol.
FAQs (Frequently Asked Questions) A: 1. For best performance, make sure your display settings are set at 1280x768@60Hz. Note: You can check the current display settings by pressing the OSD OK button once. The current display mode is shown in the product information in the OSD main controls. 2. To install the Flat Panel Adjust (FPadjust) program located on the monitor setup CD-ROM, open the CD-ROM and double click the FP_setup04.exe icon.
FAQs (Frequently Asked Questions) platforms. Q: What is a TV System? A: Television pictures are not broadcast in the same way in all countries. There are different standards: BG, DK, I and L L'. The SYSTEM setting is used to select these different standards. This is not to be confused with PAL or SECAM colour coding. PAL is used in the majority of European countries, Secam in France, the CIS and the majority of African countries. The United States and Japan use a different system called NTSC.
FAQs (Frequently Asked Questions) A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to display ASCII characters and images on digital items such as watches, calculators, portable game consoles, etc. LCD is the technology used for displays in notebooks and other small computers. Like light-emitting diode and gas-plasma technologies, LCD allows displays to be much thinner than cathode ray tube (CRT) technology.
FAQs (Frequently Asked Questions) A: On each column and row of the TFT LCD panel a data source drive and a gate drive and attached, respectively. The TFT drain of each cell is connected to the electrode. The molecular arrangement of liquid crystal elements differs acceding to whether it is impressed with voltage or not. It varies the direction of polarized light and the amount of light by letting it through different arrays of liquid crystal elements.
FAQs (Frequently Asked Questions) displays it. Since the refraction ratio of inlet light on liquid crystal varies with the inlet angle of the light, the viewing angle of a TFT is much narrower than that of a CDT. Usually, the viewing angle refers to the point where the contrast ratio is 10. Many ways to widen the viewing angle are currently being developed and the most common approach is to use a wide viewing angle film, which widens the viewing angle by varying the refraction ratio.
FAQs (Frequently Asked Questions) Q: Does the product conform to general safety standards? A: Yes. Philips LCD monitors conform to the guidelines of MPR-II standards for the control of radiation, electromagnetic waves, energy reduction, electrical safety in the work environment and recyclability. The specification page provides detailed data on safety standards. More information is provided in the Regulatory Information section.
Troubleshooting Troubleshooting Safety and Troubleshooting • FAQs • Common Problems • TV and Audio Problems • Video Problems • Remote Control Problems • Product Specific Problems • OSD Warning Message • Self-Test Feature Check (STFC) • Regulatory Information • Other Related Information This page deals with problems that can be corrected by the user. If the problem still persists after you have tried these solutions, contact your nearest Philips dealer.
Troubleshooting Shaky/Jittery Video Wavy picture or fine movement ● ● ● ● ● Missing Pixels Stuck-on Pixels Brightness Problems LCD screen has spots LCD screen has bright spots Picture too dim or too bright ● ● ● ● ● ● ● Auto adjust image through Menu -> Image Setting -> Auto Adjust Adjust Phase and Clock controls via OSD Perform the LCD Monitor TV factory reset (via Menu -> Factory Reset -> All Settings) Check environmental factors Relocate and test in other room Cycle power on-off These a
Troubleshooting Horizontal/Vertical Lines Screen has one or more lines ● ● ● ● ● Perform the LCD Monitor TV reset Auto adjust image through Menu -> Image Setting -> Auto Adjust Adjust Phase and Clock controls via OSD Perform the LCD Monitor TV self-test feature check and determine if these lines are also in self-test mode Check for bent or broken pins in the video cable connector Note: When operating in DVI mode, the Pixel Clock and Phase adjustments are not available.
Troubleshooting TV and Audio Problems ● Poor TV signal reception Abnormal picture seen from the screen ● No TV picture No picture when TV input was selected ● No sound No sound output when a program with sound was playing ● The proximity of mountains or high buildings may be responsible for ghost pictures, echoing or shadows. In this case, try manually adjusting your pictures: see 'fine tuning' or adjust the direction of the outside aerial.
Troubleshooting ● No Video No signal indicator is displayed. ● Low Quality DVD playback Picture not crisp and some color distortion ● ● No sound See video but no audio ● ● ● Check Video Input Selection ❍ Composite: Yellow colored RCA jack ❍ S-Video: Typically a round 4 pin jack ❍ Component: Typically 3 RCA jacks of Green, Red and Blue. Make sure you did not plug the video cable to video output port behind the LCD monitor TV.
Troubleshooting Cannot adjust the LCD Monitor TV with the buttons at the side of the unit OSD does not appear on the screen ● Turn the LCD Monitor TV off and unplug the power cord and then plug back and power on. For further assistance, refer to the Consumer Information Centers list and contact your local Philips distributor. RETURN TO TOP OF THE PAGE OSD Warning Messages A warning message may appear on the screen indicating the LCD Monitor TV current status.
Troubleshooting This message means that there is no video input signal. The LCD Monitor TV is in a power saving mode (in PC mode). The main OSD menu is unlocked. The main OSD menu is locked. RETURN TO TOP OF THE PAGE Self-Test Feature Check (STFC) Your the LCD Monitor TV when used as a computer display through DVI and/or VGA connection provides a self-test feature that allows you to check whether your the LCD Monitor TV is functioning properly.
Troubleshooting The floating 'Philips - self-test Feature Check' dialog box should appear on-screen (against a black background) if the LCD Monitor TV cannot sense a video signal and is working correctly. While in self-test mode, the power LED remains green and the self-test pattern will scroll through the screen continually. This box also appears during normal system operation if the video cable becomes disconnected or damaged. 4.
Regulatory Information Regulatory Information CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
Regulatory Information - TCO99, TCO03 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission, TCO: Swedish Confederation of Professional Employees) for TCO versions RETURN TO TOP OF THE PAGE Energy Star Declaration PHILIPS 300WN5 This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard.
Regulatory Information RETURN TO TOP OF THE PAGE Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Regulatory Information Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une installation résidentielle.
Regulatory Information RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
Regulatory Information Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
Regulatory Information RETURN TO TOP OF THE PAGE North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. file:///D|/My%20Documents/dfu/300WN5/english/300wn5/SAFETY/REGS/REGULAT.
Regulatory Information Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
Regulatory Information Ergonomie Hinweis (nur Deutschland) Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß 1. Reparaturen nur durch Fachpersonal durchgeführt werden. 2. nur original-Ersatzteile verwendet werden. 3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.
Regulatory Information WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A. S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3pin plug fitted in its place.
Regulatory Information connected to the terminal in the plug which is marked with the letter "E" or by the Earth symbol or coloured GREEN or GREEN AND YELLOW. 2. The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured BLACK. 3. The BROWN wire must be connected to the terminal which marked with the letter "L" or coloured RED. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires.
Other Related Information Other Related Information Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information for Users in the U. S. • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
Philips Pixel Defect Policy Philips Pixel Defect Policy Product Features • Technical Specifications • Resolution and Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips' LCD Panel Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practise stringent quality control.
Philips Pixel Defect Policy Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category. Bright Dot Defects appear as pixels or sub pixels that are always lit or 'on'.
Philips Pixel Defect Policy One dark sub pixel Two or three adjacent dark sub pixels Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects.
Philips Pixel Defect Policy * Here in Tiny Bright Dot is defined as "for Red and Blue" the bright area should be no longer than 1/2 sub-pixel and for green the bright area should be no larger than 1/3 sub-pixel.
Connecting to Your PC, TV Antenna, DVD/VCR etc. Connecting to Your PC, TV Antenna, DVD/VCR etc. Product Description • Accessory Pack • Connecting to Your PC, TV Antenna, DVD/VCR etc. • Getting Started • Optimizing Performance Accessory Pack Unpack all the parts. Power cable Remote control & batteries DVI-D cable VGA signal cable file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. E-DFU pack Accessories below are available for TV model only. S-video cable Base 2x 5W Detachable Speakers RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. Setting up and connecting your monitor/TV CAUTION: Ensure that the power to the monitor/TV is switched off before the installation. - Connecting the monitor/TV ● Connect the cables to the rear of your monitor/TV according to the numbers: TV model file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. Audio/Video model file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. Monitor model file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. RETURN TO TOP OF THE PAGE - Connect to PC ● ● ● ● Connect the cables to the back of your computer by following step 1~3. If your monitor displays the computer image the installation has been completed successfully. If installation was not successful, see the Troubleshooting section. For installation of the monitor driver for Microsoft Windows®, see the Monitor Driver Installation section (Getting Started).
Connecting to Your PC, TV Antenna, DVD/VCR etc. ● Connect to DVD/VCR /VCD through SCART (for Europe only) file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. ● Connect to DVD/VCR /VCD through composite video (CVBS) file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. ● Connect to DVD/VCR /VCD through component video (YPbPr) file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. RETURN TO TOP OF THE PAGE Connecting to Cable TV file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. Antenna Progressive video and HDTV connections for digital high-definition picture file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/300WN5/english/300wn5/INSTALL/connect.
Getting Started Getting Started Product Description • Connecting to Your PC, TV Antenna, DVD/VCR etc.• Getting Started • Optimizing Performance Getting Started Use the information file ( .inf) for Windows® 95/98/2000/Me/XP or later The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for Windows® 95/98/2000/Me/XP. This information file ( .
Getting Started For Windows® Me 1. 2. 3. 4. 5. 6. 7. Start Windows® Me Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. Double click on the 'Display' Icon. Select the 'Settings' tab then click on 'Advanced...'. Select 'Monitor' button, then click on 'Change...' button. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.
Getting Started 7. 8. 9. 10. 11. 12. 13. 14. - If the 'Properties' button is active, click on 'Properties' button. Please follow the steps below. Click on the 'Driver' tab and then click on 'Update Driver...' button. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button. Click on the 'Have disk...' button, then click on the 'Browse...
Your Philips F1rst Choice Warranty Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty.
Your Philips F1rst Choice Warranty ● ● ● ● ● Damage is caused by accidents including but not limited to lightning, water or fire, misuse or neglect; Reception problems caused by signal conditions or cable or antenna systems outside the unit; Defects caused by abuse or misuse of the monitor; Product requires modification or adaptation to enable it to comply with local or national technical standards, which apply in countries for which the product was not originally designed, manufactured, approved and/or
Your Philips F1rst Choice Warranty Information. Or you can reach us via: Website: http://www.philips.com/support file:///D|/My%20Documents/dfu/300WN5/english/warranty/war_1st.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
United States Guarantee PHILIPS LIMITED WARRANTY One (1) Year Labor and Parts Repair PHILIPS CONSUMER ELECTRONICS warrants this product against defect in material or workmanship, subject to any conditions set forth as follows: PROOF OF PURCHASE: You must have proof of the date of purchase to receive warranted repair on the product. A sales receipt or other document showing the product and the date that your purchased the products as well as the authorized retailer included, is considered such proof.
F1rst Choice Contact Information F1rst Choice Contact Information Country Telephone number Tariff Austria 01 546 575 603 Local call tariff Belgium 070 253 010 0.17 Cyprus 800 92256 Free of Charge Denmark 3525 8761 Local call tariff Finland 09 2290 1908 Local call tariff France 08 9165 0006 0.23 Germany 0180 5 007 532 0.12 Greece 00800 3122 1223 Local call tariff Ireland 01 601 1161 Local call tariff Italy 199 404 042 0.
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Belarus • Bulgaria • Croatia • Czech Republic • Estonia • Dubai • Hong Kong • Hungary • India • Indonesia • Korea • Latvia • Lithuania • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Romania • Russia • Serbia & Montenegro • Singapore • Slovakia • Slovenia • South Africa • Taiwan • Thailand • Turkey • Ukraine
Consumer Information Centers CROATIA Renoprom d.o.o. Mlinska 5, Strmec HR - 41430 Samobor Tel: +385 1 333 0974 ESTONIA FUJITSU SERVICES OU Akadeemia tee 21G EE-12618 Tallinn Tel: +372 6519900 www.ee.invia.fujitsu.com HUNGARY Serware Szerviz Vizimolnár u. 2-4 HU - 1031 Budapest Tel: +36 1 2426331 Email: inbox@serware.hu www.serware.hu LATVIA ServiceNet LV Jelgavas iela 36 LV - 1055 Riga, Tel: +371 7460399 Email: serviss@servicenet.lv LITHUANIA ServiceNet LT Gaiziunu G.
Consumer Information Centers ROMANIA Blue Ridge Int'l Computers SRL 115, Mihai Eminescu St., Sector 2 RO - 020074 Bucharest Tel: +40 21 2101969 SERBIA & MONTENEGRO Tehnicom Service d.o.o. Bulevar Vojvode Misica 37B YU - 11000 Belgrade Tel: +381 11 3060 886 SLOVAKIA Datalan Servisne Stredisko Puchovska 8 SK - 831 06 Bratislava Tel: +421 2 49207155 Email: servis@datalan.sk SLOVENIA PC HAND Brezovce 10 SI - 1236 Trzin Tel: +386 1 530 08 24 Email: servis@pchand.si POLAND Zolter ul.
Consumer Information Centers TURKEY Türk Philips Ticaret A.S. Yukari Dudullu Org.San.Bolgesi 2.Cadde No:22 34776-Umraniye/Istanbul Tel: (0800)-261 33 02 UKRAINE Comel Shevchenko street 32 UA - 49030 Dnepropetrovsk Tel: +380 562320045 www.csp-comel.com Latin America ANTILLES Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (09)-4612799 Fax : (09)-4612772 ARGENTINA Philips Antillana N.V.
Consumer Information Centers CHILE Philips Chilena S.A. Avenida Santa Maria 0760 P.O. box 2687Santiago de Chile Phone: (02)-730 2000 Fax : (02)-777 6730 COLOMBIA Industrias Philips de Colombia S.A.-Division de Servicio CARRERA 15 Nr. 104-33 Bogota, Colombia Phone:(01)-8000 111001 (toll free) Fax : (01)-619-4300/619-4104 MEXICO Consumer Information Centre Norte 45 No.669 Col. Industrial Vallejo C.P.02300, -Mexico, D.F. Phone: (05)-3687788 / 9180050462 Fax : (05)-7284272 PARAGUAY Av. Rca.
Consumer Information Centers PERU Philips Peruana S.A. Customer Desk Comandante Espinar 719 Casilla 1841 Limab18 Phone: (01)-2136200 Fax : (01)-2136276 URUGUAY Rambla O'Higgins 5303 Montevideo Uruguay Phone: (598) 619 66 66 Fax: (598) 619 77 77 Customer Desk: Phone: 0004054176 VENEZUELA Industrias Venezolanas Philips S.A. Apartado Postal 1167 Caracas 1010-A Phone: (02) 2377575 Fax : (02) 2376420 Canada CANADA Philips Electronics Ltd.
Consumer Information Centers AUSTRALIA Philips Consumer Electronics Consumer Care Center Level 1, 65 Epping Rd North Ryde NSW 2113 Phone: 1300 363 391 Fax : +61 2 9947 0063 NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (toll free) Fax : 0800 288 588 Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA SHANGHAI Rm 1007, Hongyun Building, No.
Consumer Information Centers HONG KONG Philips Electronics Hong Kong Limited Consumer Service Unit A, 10/F. Park Sun Building 103-107 Wo Yi Hop Road Kwai Chung, N.T. Hong Kong Phone: (852)26199663 Fax: (852)24815847 INDIA Phone: 91-20-712 2048 ext: 2765 Fax: 91-20-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr.
Consumer Information Centers INDONESIA Philips Group of Companies in Indonesia Consumer Information Centre Jl.Buncit Raya Kav. 99-100 12510 Jakarta Phone: (021)-7940040 ext: 2100 Fax : (021)-794 7511 / 794 7539 KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong.
Consumer Information Centers PHILIPPINES PHILIPS ELECTRONICS & LIGHTING, INC. Consumer Electronics 48F PBCOM tower 6795 Ayala Avenue cor VA Rufino St. Salcedo Village 1227 Makati City, PHILS Phone: (02)-888 0572, Domestic Toll Free: 1-800-10-PHILIPS or 1-800-10-744 5477 Fax: (02)-888 0571 SINGAPORE Accord Customer Care Solutions Ltd Authorized Philips Service Center Consumer Service 620A Lorong 1 Toa Rayoh Singapore 319762 Tel: +65 6882 3999 Fax: +65 6250 8037 TAIWAN Philips Taiwan Ltd.
Consumer Information Centers MOROCCO Philips Electronique Maroc 304,BD Mohamed V Casablanca Phone: (02)-302992 Fax : (02)-303446 SOUTH AFRICA PHILIPS SA (PTY) LTD Customer Care Center 195 Main Road Martindale, Johannesburg P.O. box 58088 Newville 2114 Telephone: +27 (0) 11 471 5194 Fax: +27 (0) 11 471 5123 E-mail: phonecare.za@philips.com Middle East DUBAI Philips Middle East B.V. Consumer Information Centre P.O.
