Register your product and get support at www.philips.
Model Serial www.philips.com/support Österreich 0810 000205 €0.07 pro Minute België/Belgique 078250145 €0.06 Per minuut/Par minute България +3592 489 99 96 Местен разговор Hrvatska 01 6403 776 Lokalni poziv Česká republika 800142840 Bezplatný hovor Danmark 3525 8759 Lokalt opkald Estonia 6008600 local Suomi 09 2311 3415 paikallispuhelu France 0821 611655 €0.09 Par minute Deutschland 01803 386 852 €0.
Back connector for 19-22 inch TV Back connector for 26 inch TV and larger 1 Notice 2 2 Important 4 3 TV overview 6 6 6 Side controls and indicators Remote control 4 Use your product Switch your TV on/off or to standby Switch channels Watch connected devices Adjust TV volume Use teletext 5 Use more of your product Access TV menus Remove devices from the home menu Change picture and sound settings Use advanced teletext features Create and use lists of favourite channels Use the Electronic Programme G
1 Notice 2009 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
3 En g l ish Refit the fuse cover. In order to maintain conformity to the EMC directive, the mains plug on this product must not be detached from the mains cord cable. Copyright VESA, FDMI and the VESA Mounting Compliant logo are trademarks of the Video Electronics Standards Association. ® Kensington and Micro Saver are registered US trademarks of ACCO World Corporation with issued registrations and pending applications in other countries throughout the world.
• 2 Important • Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply. Safety • Risk of electric shock or fire! • Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use.
• • • • • Disposal of your old product and batteries Eng lish • the value printed on the back of the TV. Never connect the TV to the power outlet if the voltage is different. Risk of injury, fire or power cord damage! Never place the TV or any objects on the power cord. To easily disconnect the TV power cord from the power outlet, ensure that you have full access to the power cord at all times. When you disconnect the power cord, always pull the plug, never the cable.
3 TV overview Remote control This section gives you an overview of commonly used TV controls and functions. Side controls and indicators 1 2 22 21 20 4 19 3 4 5 6 7 8 3 18 9 17 10 11 16 12 2 1 a POWER: Switches the product on or off. The product is not powered off completely unless it is physically unplugged. b P/CH +/-: Switches to the next or previous channel. c 13 SOURCE: Selects connected devices. d VOLUME +/-: Increases or decreases volume.
• • b (Standby-On) Switches the TV to standby if it is on. Switches on the TV if it is in standby. MENU Toggles the main menu on or off. c MHEG/TELETEXT Toggles teletext on or off. d SOURCE Selects connected devices. o SOUND(Smart Sound) Launches the sound menu. p +/- (Volume +/-) Increases or decreases volume. q BACK P/P (Previous channel) • Returns to a previous screen. • Returns to the previously viewed channel. r GUIDE Switches between channel grid and programme list.
4 Use your product This section helps you perform basic operations (see ‘Use more of your product’ on page 10). Note • If you cannot locate your remote control and want to switch on the TV from standby, press P/CH +/- or SOURCE at the side of the TV. Switch channels Switch your TV on/off or to standby To switch on • If the standby indicator is off, press POWER at the side of the TV. • If the standby indicator is red, press (Standby-On) on the remote control.
• • Press Press to mute the sound. again to restore the sound. Eng lish Watch connected devices Note • Switch on the device before selecting it as a Use teletext source on the TV. Use the source button 1 Press SOURCE. » The source list appears. 2 Press the Navigation buttons to select a device. 3 Press OK to confirm your choice. » The TV switches to the selected device. Adjust TV volume 1 Press MHEG/TELETEXT. » The main index page appears.
5 Use more of your product Remove devices from the home menu Access TV menus 1 2 3 If a device is no longer connected to the TV, remove it from the home menu. Menus help you to install channels, change picture and sound settings and access other features. 1 Press MENU. » The menu screen appears. Add new device 4 Press Press MENU to select a device to remove. Press OPTIONS. » The [Remove device] list appears. Press OK and select [Remove] to remove the device.
• • • • • 3 [Personal]Lists customised personal picture settings. [Vivid]Maximises picture settings. [Standard]Adjusts picture settings to suit most environments and types of video. [Movie]Applies picture settings ideally suited for movie viewing. [Game]Applies picture settings maximised for fast-moving games. [Energy saving]Applies low-energy picture settings. • • • Press OK to confirm your choice. » The selected smart picture setting is applied. Manually adjust picture settings 1 2 Press MENU.
Summary of picture formats [Unscaled]For HD and PC mode only, and in selected models only. Allows maximum sharpness. Some distortion may be present due to the broadcaster’s systems. Set your PC resolution to wide screen mode for best results. The following picture settings can be configured. Note • Depending on the format of the picture source, some picture settings are not available. [Auto format](Not for PC mode.) Enlarges the picture automatically to best fit the screen. The subtitles remain visible.
Smart sound • Standard Bass Sound Treble Volume Features [Delta volume]Levels out volume differences between channels or connected devices. Switch to the connected device before you change the delta volume. Vol.vis.impaired Installation Software update 3 Balance Audio language English Dual I-II Dual I Press to select one of the following sound settings. • [Smart sound]Accesses pre-defined smart sound settings. • [Bass]Adjusts the bass level. • [Treble]Adjusts the treble level.
Select teletext subpages 3 A teletext page can hold several subpages. Subpages are displayed on a bar next to the main page number. Press to select [Show fav. ch.] and press OK. » The favourite lists appear. 4 Press to select a favourite list and press OK. » Only channels in the favourite list appear in the channel grid. 1 Press MHEG/TELETEXT . » The teletext screen appears. 2 3 Press to select a teletext page. Press to enter a subpage. Select T.O.P. teletext broadcasts Table Of Pages (T.O.P.
Press to select [Mark as favourite] and press OK. » The favourite lists appear. Use the Electronic Programme Guide 5 Press to select a favourite list to add the channel to. 6 Press OK. » The channel is added to the favourite list. EPG is an on-screen guide available for digital channels.
Use the EPG options menu 3 Press to set the sleep time. » The sleeptimer can be up to 180 minutes in steps of five minutes. If set to zero minutes, the sleeptimer is switched off. 4 Press OK to activate the sleeptimer. » The TV switches to standby after the pre-defined period of time. Use the EPG options menu to set or clear reminders, change day and access other useful EPG options. 1 2 3 4 5 Press GUIDE. Press OPTIONS. » The EPG menu appears. Press to select one of the following options.
1 2 3 4 5 6 7 8 Press MENU. 4 5 Press to select [Setup] > [Features] > [Set code]. Press OK or to enter the code setup. Enter your code using the Numeric buttons. Press to select [Lock] or [Unlock]. Press OK to confirm. » All channels and connected devices are locked or unlocked. Note • If you select [Lock], you have to enter your code every time you turn on your TV to access all channels and connected devices. Re-enter the same code in the new dialogue box for confirmation.
5 6 Enter your code and press OK. 3 Repeat the process to unlock more channels. Enter the three-digit page number of the subtitle page with the Numeric buttons. 4 Press MHEG/TELETEXT to switch off teletext. 5 Press SUBTITLE. » The [Subtitle mode] menu appears. 6 Select [On] to display subtitles always or [On during mute] to display subtitles only when audio is muted. 7 Press OK to enable subtitles. Note • Restart the TV for the change to take effect.
Press OK or to enter the list of available languages. 4 5 Press to select a subtitle language. Change the time zone 1 2 Press OK to enable your selection. Tip • You can also access [Subtitle language] menu while watching TV by pressing [Subtitle language]. 3 4 OPTIONS > Press MENU. Eng lish 3 Press to select [Setup] > [Installation] > [Clock] > [Time zone]. Press to select your time zone. Press OK to confirm.
1 2 2 Turn on the TV. Connect the USB device to the USB port on the side of your TV. » The home menu appears. Press: • OK to pause the slide show. » The icon appears. • • Press to go back or move forward to the next image. BACK to stop the slide show. Add new device Browse USB Watch TV Change slide show settings Setup 3 4 Press 1 When viewing a slide show, press OPTIONS. » The slide show options menu appears. 2 Press to select one of the following. • [Start/Stop slide.
When listening to music, press OPTIONS to access one of the following music settings. • [Start/Stop play] • [Repeat/Play once] • [Shuffle on/off] • [Show info] • [TV speakers] Disconnect a USB storage device Update the TV software Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available. Check www.philips.com/support for availability.
• Select [Update now] to update the software immediately. Select [Remind me later] to exit the update screen at that time and be reminded later. Select [Cancel] to skip the update. • • 2 If you select [Cancel], you can manually access the OAD update by selecting [Setup] > [Software update] > [Local updates] > [OAD]. 3 Select the available version of OAD and press OK. 4 Follow the on-screen instructions to start the update.
Eng lish Reset the TV to factory settings You can restore the default picture and sound settings of your TV. Channel installation settings remain the same. 1 2 Press MENU. Press to select [Setup] > [Installation] > [Factory settings]. 3 Press OK or to enter the [Factory settings] menu. » A factory setting message appears. 4 5 Select [Reset] to start resetting. Press MENU to exit.
6 Install channels Picture Sound The first time you set up your TV, you are prompted to select a menu language and to install TV and digital radio channels (if available). This chapter provides instructions on how to re-install and fine tune channels. Language Menu language Channel install. Channel assistant Preferences Location Decoder Channel Clock Auto clock Factory settings Action Features Installation Software update 3 Automatically install channels Press OK or to enter the menu.
Digital channels found Analogue channels found 7 0 Picture Stop 3 Sound Sound Analogue: Manual When installation is complete, press OK to return to [Installation] menu. You can choose to enable auto update of channels, if your TV is in standby mode. If you enable this feature, the channels stored in your TV will be updated every morning according to the channel information in the broadcast. 3 Channel assistant Channel install.
Step 3 Fine-tune analogue channels 1 2 3 4 5 6 Press MENU. Press to select [Setup] > [Installation] > [Channel install.] > [Analogue: Manual]. » The [Analogue: Manual] menu appears. Press OK or to select [Fine-tune] and then to enter [Fine-tune]. Press to adjust frequency. Reorder channels After you install channels, you can rearrange the order in which they appear. 1 When watching TV, press OK to display the channel grid . 2 Press OPTIONS. » The channel options menu appears.
This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start. a PC IN (VGA and AUDIO IN) Audio and video input from a computer. PC IN(AUDIO) Note VGA • Different types of connectors may be used to connect a device to your TV, depending on availability and your needs.
c EXT 1 (CVBS and RGB) Analogue audio and video input from analogue or digital devices such as DVD players or game consoles. AUDIO IN f SPDIF OUT Digital audio output to home theatres and other digital audio systems. SPDIF OUT d TV ANTENNA Signal input from an antenna, cable or satellite. TV ANTENNA e AV OUT (VIDEO OUT and AUDIO OUT L/R) Audio and video output to analogue devices such as another TV or a recording device.
b EXT 3 (Y Pb Pr and AUDIO L/R) Analogue audio and video input from analogue or digital devices such as DVD players or game consoles. Eng lish Back connector for 26 inch TV and larger SPDIF OUT a HDMI 1 (HDMI and AUDIO IN) Digital audio and video input from highdefinition digital devices such as Blu-ray players. c EXT 1 (RGB and CVBS)/EXT 2 (CVBS) Analogue audio and video input from analogue or digital devices such as DVD players or game consoles. EXT 2 supports S-Video.
d TV ANTENNA Signal input from an antenna, cable or satellite. a COMMON INTERFACE Slot for a Conditional Access Module (CAM). TV ANTENNA b AUDIO L/R Audio input from analogue devices connected to VIDEO. e SPDIF OUT Digital audio output to home theatres and other digital audio systems. f SERV. U For software update. c VIDEO Composite video input from analogue devices such as VCRs. Side connector 1 2 3 4 5 30 EN d USB Data input from USB storage devices.
• DVI-HDMI cable For TV of size 19-22 inch Eng lish e HDMI (Only for TVs 26 inches and larger) Digital audio and video input from highdefinition digital devices such as Blu-ray players.
Use a Conditional Access Module Access CAM services 1 After inserting and activating the CAM, press MENU. A Conditional Access Module (CAM) is provided by digital TV service operators to decode digital TV channels. 2 Press to select [Setup] > [Features] > [Common interface]. » Applications provided by the digital TV service operator appear on the screen. Note Note • If required, refer to documentation from your operator on how to insert a smart card into the Conditional Access Module.
Use one-touch standby Press and hold Standby on the TV’s or device’s remote control for at least three seconds. » The TV and all connected HDMI devices switch to standby. Eng lish 1 Use a Kensington lock There is a Kensington security slot at the back of the TV. Prevent theft by looping a Kensington lock between the slot and a permanent object, such as a heavy table.
8 Product information Product information is subject to change without notice. For detailed product information, go to www.philips.com/support.
This section describes commonly encountered issues and accompanying solutions. General TV issues The TV does not switch on: • Disconnect the power cable from the power outlet. Wait for one minute then reconnect it. • Check that the power cable is securely connected. The remote control is not working properly: • Check that the remote control batteries are correctly inserted according to the +/- orientation. • Replace the remote control batteries if they are flat or weak.
The picture does not fit the screen; it is too big or too small: • Try using a different picture format. The picture position is incorrect: • Picture signals from some devices may not fit the screen correctly. Check the signal output of the device. Sound issues There is a picture but sound quality is poor: • If a HDMI-to-DVI adaptor or HDMI to DVI cable is used, check that an additional audio cable is connected to AUDIO L/R or AUDIO IN (mini-jack only).
display resolution 34 Eng lish 10 Index E B batteries bracket 34 34 C Channel list favourite troubleshooting update channels favourite list install automatic manual rename test reception child lock ratings lock clock computer format technical specifications Conditional Access Module connections HDMI troubleshooting mains cord technical specifications troubleshooting 14 35 14 14 24 25 26 26 18 19 34 32 32 32 32 33 5 F factory settings favourite list select set up 23 14 14 H HDMI cable troubleshooting
music digital radio USB 21 20 O One-touch play One-touch standby 32 33 P picture format picture format change troubleshooting Picture settings 11 35 10 R ratings reception remote control overview technical specifications 18 35 6 34 S settings assistant sleep timer Smart card Smart settings software version sound settings subtitles language on analogue channel on digital channel 10 16 32 10, 12 21 12 18 18 18 T Table of Pages technical specifcations Teletext features subpages table of pages timer on
EN 39
40 EN
© 2009 Koninklijke Philips Electronics N.V. All rights reserved.