2504.4 en 13-12-2006 08:29 Pagina 1 About this User Manual EN This manual contains all information you will need to initially install and operate your new TV. Also read the help texts which are being displayed at the bottom of the screen. If this instruction manual does not give an answer or if ‘Troubleshooting’ does not solve your TV problem, you can call your Local Philips Customer or Service Centre. See the supplied Worldwide guarantee booklet.
504.4 en 13-12-2006 08:29 Pagina 2 Safety warnings EN General Do not insert the power plug in a wall socket or hang the TV to the wall before all connections are made. • Place or hang the TV wherever you want, but make sure that air can circulate freely through the ventilation slots. • TV channel logo: present a problem if they are bright and stationary.
2504.4 en 13-12-2006 08:29 Pagina 3 Getting started EN Before you start Warning: do not insert the mains cord into the mains at the bottom of the TV and in a wall socket or hang the TV on the wall before all connections are made. Before you switch on your TV, connect all your peripheral equipment. See To make video and audio connections, p. 46. Overview of the rear connector panel There is a wide range of audio and video equipment that can be connected to your TV.
2504.4 en 13-12-2006 08:29 Pagina 4 Getting started (Continued) EN Overview of the side connector panel - To connect a camera, camcorder or game, see To make video and audio connections, p. 47. - To connect a headphone, see To make video and audio connections, p. 47. - To connect a USB device or memory card, see Multimedia browser, p. 39. Connect the antenna < Insert the aerial plug firmly into the aerial socket x at the bottom of the TV. Tip: for best quality use the suppressor cable supplied.
2504.4 en 13-12-2006 08:29 Pagina 5 Use of the remote control RC4401/01 - RC4420/01 EN B Standby Press to switch the TV from or to standby mode. When switched to standby, a red indicator on the TV lights up. Attention: the TV is never powered off completely unless it is physically unplugged. TV Press to select TV mode. DVD STB VCR AUX Press one of these keys to set your remote control to operate a peripheral device. See Audio and Video equipment keys, p. 57.
2504.4 en 13-12-2006 08:29 Pagina 6 Use of the remote control RC4401/01 - RC4420/01 (Continued) EN V Volume Press + or - to adjust the volume. ¬ Mute key: interrupt the sound or restore it. +P- Channel selection - to browse through the TV channels and sources stored and marked in the Favourite channels lists; - to select a page in Teletext mode; - to quickly browse through the lists in the menus; - to switch the TV on from standby mode. a 0/9 Digit keys To select a TV channel between 0 and 999.
2504.4 en 13-12-2006 08:29 Pagina 7 Use of the remote control RC4401/01 - RC4420/01 (Continued) b Dual screen/PIP Press the b key to switch on or off Dual screen or PIP, according to the format selection made in the PIP format list. See p. 24. PIP allows you to call up a subscreen within the main screen enabling you to watch two TV channels or a TV channel and pictures from a peripheral at the same time.
2504.4 en 13-12-2006 08:29 Pagina 8 Use of the OPTION key EN The Option key allows you to display the Quick access menu which will give you direct access to some features and menu options. 1. Press the OPTION key. > The Quick access menu appears. 2. Press the cursor up/down to select a menu item. 3. Press the OK key to jump to the selected menu item in the TV menu. (Except for the Clock option). 4. Use the cursor keys to make a selection. 5. Press the option key to exit.
2504.4 en 13-12-2006 08:29 Pagina 9 Introduction: Digital TV EN Besides traditional analogue broadcasts, you can also receive digital broadcasts via a roof or loft mounted digital antenna in countries where those signals are available and which are supported by this TV.Verify if the country you are now located and you have selected during the installations (see further), supports digital video broadcasting via antenna. See www.philips.
2504.4 en 13-12-2006 08:29 EN Pagina 10 First time installation (Continued) Step 1: select your on-screen language After the Welcome screen you are asked to select a language of the TV's on-screen menus.The text of the header and the info on screen continuously change language. Also the digital audio and subtitle language will be set to the selected menu language. 1. Press the cursor up/down to highlight your language. 2. Press the OK key on the remote control. 3.
2504.4 en 13-12-2006 08:29 Pagina 11 First time installation (Continued) EN Step 3: Settings assistant: select your TV settings PHILIPS Installation This will help you to complete the Settings assistant. 1. Television 2. Settings assistant Previous Next Skip Stop PHILIPS Settings assistant Please select your location before continuing: Home Shop 3. 4. 5.
2504.4 en 13-12-2006 08:29 Pagina 12 How to navigate through the menus EN Introduction A lot of guiding instructions, help texts and messages will be displayed on your TV when you use the menus or when you try to execute an action. Read the help texts which are being displayed on the specific item highlighted. The colour keys at the bottom of the screen refer to the different actions which may be executed.
2504.4 en 13-12-2006 08:29 Pagina 13 How to navigate through the menus (continued) TV menu TV settings Features Installation Info TV settings Settings assistant Reset to standard Picture Sound Ambilight EN 4. Use the cursor up/down to select a menu item.
2504.4 en 13-12-2006 08:29 Pagina 14 Use of the TV menu settings EN Television TV menu TV channels Programme guide Multimedia The TV menu allows you to access and change settings and preferences in case you want to change the First time installation settings and/or you want to control the settings of special TV functions, features and peripheral equipment.
2504.4 en 13-12-2006 08:29 Pagina 15 Use of the TV menu settings (continued) EN B. Use of the Standards settings (if present) This allows you to reset your settings for viewing and listening to predefined factory settings. TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Reset to standard Current Natural Vivid Subtle 1. Select Reset to standard and press the cursor right.
2504.4 en 13-12-2006 08:29 Pagina 16 Adjust picture menu settings EN TV menu TV settings Features Installation TV settings Settings assistant Reset to standard Picture Sound Ambilight Info The picture menu contains the settings that affect the quality of the picture. 1. Press the MENU/BROWSE key on the remote control. > The main menu appears. 2. Select TV menu and press the cursor right. > The TV menu is moved to the left. 3. Select TV settings and press the cursor right.
2504.4 en 13-12-2006 08:29 Pagina 17 Adjust picture menu settings (Continued) Custom tint (only when Tint is set to Custom) TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info EN Picture ............. Custom tint Pixel Plus Digital Natural Mo.. Clear LCD Dynamic contrast ............. Fine tunes the white point (WP) and black level (BL) of the picture. 1. Select Custom tint and press the cursor right. 2.
2504.4 en 13-12-2006 08:29 Pagina 18 Adjust picture menu settings (Continued) EN DNR TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Picture ............. DNR MPEG artefact red. Colour enhancem.. Active control Light sensor Picture format < DNR automatically filters out and reduces the image noise. This improves picture quality when receiving weak signals. Select Off, Minimum, Medium or Maximum according to the image noise in the picture.
2504.4 en 13-12-2006 08:29 Pagina 19 Adjust sound menu settings TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Sound Equalizer Volume Balance Digital audio lang.. Dual I/II Mono/Stereo ............. EN The sound menu contains the settings that affect the quality of the sound. 1. Press the MENU/BROWSE key on the remote control. > The main menu appears. 2. Select TV menu and press the cursor right. > The TV Menu is moved to the left. 3.
2504.4 en 13-12-2006 08:29 Pagina 20 Adjust sound menu settings (Continued) EN Dual I/II TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Sound ............. Mono/Stereo Surround mode Headphone volume AVL Delta volume Auto surround Allows you to select, per channel, Dual I or Dual II, when dual sound transmission is available. Mono/Stereo Allows you to select, per TV channel, Mono or Stereo sound when stereo broadcasts are available.
2504.4 en 13-12-2006 08:29 Pagina 21 Enjoy Ambilight TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Ambilight Ambilight Brightness Mode Colour Custom colour Separation ............. EN The ambilight menu contains the settings for controlling the ambient lighting. Using ambient light gives a more relaxed viewing experience and improves perceived picture quality. Analysis of the picture content adapts the colours continuously.
2504.4 en 13-12-2006 08:29 Pagina 22 Enjoy Ambilight (Continued) EN Mode Allows you to choose for constant background lighting or for background lighting that matches the images displayed on the screen. TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Ambilight ............. Mode Colour Custom colour Separation Colour boost Balance < Use the cursor keys to select Colour, Relaxed, Moderate or Dynamic.
2504.4 en 13-12-2006 08:29 Pagina 23 Enjoy Ambilight (Continued) Custom colour TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info EN Ambilight ............. Mode Colour Custom colour Separation Colour boost Balance Note: only available when Custom has been selected in the Colour menu. < < Allows you to customise the ambilight colour. Select Palette to select the general colour of the light output. Select Saturation to adjust the colourfulness of the light.
2504.4 en 13-12-2006 08:29 Pagina 24 Adjust feature menu settings EN The Features menu allows you to control the settings of special TV functions, features and accessory equipments. TV menu TV settings Features Installation Info Features PIP format Subtitle Digital subtitle lan.. Sleeptimer Child lock Set/Change code ............. 1. Press the MENU/BROWSE key on the remote control. > The main menu appears. 2. Select TV menu and press the cursor right. > The TV Menu is moved to the left. 3.
04.4 en 13-12-2006 08:29 Pagina 25 Adjust feature menu settings (Continued) TV menu TV settings Features Installation Features ............. Sleeptimer Child lock Set/Change code On timer Common interface Demo EN Sleeptimer This sets a time period after which the TV automatically switches to standby. 1. Select Sleeptimer. 2. Press the cursor right. 3. Select a value with the cursor up/down. > The list will have values from 0 to 180 minutes.When 0 is selected, the sleeptimer is switched off.
2504.4 en 13-12-2006 08:29 Pagina 26 Adjust feature menu settings (Continued) EN TV menu TV settings Features Installation Features ............. Sleeptimer Child lock Set/Change code On timer Common interface Demo Set code/Change code This allows you to set or change the personal 4-digit access code that is used in the different lock functions of the TV. < < Info Select Set or Change code. > If no PIN-code exists yet, the menu item is set to Set code. Follow the instructions on screen.
2504.4 en 13-12-2006 08:29 Pagina 27 Adjust feature menu settings (Continued) TV menu TV settings Features Installation Features EN Common interface Note: this functionality is only available in certain countries. ............. Sleeptimer Child lock Set/Change code On timer Common interface Demo This allows you to access common interface applications defined by the service provider of the Common Interface (CI) module.
2504.4 en 13-12-2006 08:29 Pagina 28 How to search for and store TV channels EN Tip: you will need this chapter only if you want to change the installation settings. Television TV menu TV channels Programme guide Multimedia Media servers TV menu TV settings Features Installation Installation Languages Country Time zone Channels Manual network i.. Preferences .............
2504.4 en 13-12-2006 08:29 Pagina 29 How to search for and store TV channels (Continued) TV menu TV settings Features Installation Installation ............. Manual network i.. Preferences Connections Decoder Factory settings Software upgrade EN Select your country This allows you to select the country where you are now located.
2504.4 en 13-12-2006 08:29 Pagina 30 How to search for and store TV channels (Continued) EN TV menu Digital: test reception (only with Digital TV broadcasting) This allows you to see the quality and the strength of the signal reception for a digital frequency.This enables you to find the antenna position that gives the best reception. Installation Channels Autom. installation Languages Installation update Country Digital: test recept.. Time zone Analogue: manual.. Channels Manual network i..
2504.4 en 13-12-2006 08:29 Pagina 31 Rearrange the channel number list TV menu Installation Languages Country Time zone Channels Manual network i.. Preferences Connections ............. Channels Autom. installation Installation update Digital: test recept.. Analogue: manual.. Rearrange 1. 2. 4. TV menu/Installation This allows you to change the order of the stored TV channels. Select the channel you want to change place. Press the yellow colour key to move up a single position in the list.
2504.4 en 13-12-2006 EN 08:29 Pagina 32 Manual network installation See the supplied separate Connected Planet guide for further explanation of this functionality. Set your preferences This menu contains items that can set or adjust various special TV functions and that will typically be accessed only occasionally. TV menu Installation ............. Channels Manual network i.. Preferences Connections Decoder Factory settings Software upgrade Info Preferences Location Teletext 2.
2504.4 en 13-12-2006 08:29 Pagina 33 Select your connections TV menu Installation ............. Time zone Channels Manual network i.. Preferences Connections Decoder Factory settings Software upgrade Info Connections EXT1 EXT2 EXT3 HDMI 1 HDMI 2 VGA Side AUDIO IN L/R DIGITAL AUDIO IN EN This allows you to select the peripheral equipment you have connected to the audio and video connectors. 1. Select Connections. 2. Press the cursor right. 3.
2504.4 en 13-12-2006 08:29 Pagina 34 Select a Decoder channel number EN This allows you to define one or more channel numbers as decoder channel numbers when a decoder or a descrambler is connected to EXT1 or EXT2. TV menu Installation Decoder Channel ............. Status Channels Manual network i.. Preferences Connections Decoder Factory settings Software upgrade 1. Select the channel number under which you have stored the programme that comes from your decoder or descrambler. 2. Select Status. 3.
2504.4 en 13-12-2006 08:29 Pagina 35 How to upgrade the TV software TV menu EN This allows you to upgrade your TV software using a USB device. Installation Software upgrade Current softw. info ............. Local upgrades Channels Manual network i.. Announcement Preferences Connections Decoder Factory settings Software upgrade Info USB device upgrade It is possible to initiate an upgrade procedure from a USB device before you start up the TV.
Create your favourite list EN This allows you to select up to four favourite channels lists with your preferred TV channels and radio stations. For example, each member of your family can create his/her own favourite list. In addition to the favourite channel lists you may also select a list with only digital TV channels or a list with only the radio channels or a list with only the analogue channels.
2504.4 en 13-12-2006 08:29 Pagina 37 Create your favourite channels list (Continued) EN To select only TV or only radio channels on the All channels list When the All channels list is displayed or selected you may filter the list and select a list with only the TV channels or a list with only the radio channels. 1. Press the FAV key. > The last selected channel list appears. 2. Press the cursor left. 3. Select the All channels list and press the cursor right. 4. Press the red colour key to filter. 5.
2504.4 en 13-12-2006 08:29 Pagina 38 EPG (Electronic Programme Guide) (Continued) EN a a 2. Press the green colour key on the remote control to watch/listen to the selected programme currently on air. 3. Press the red colour key to mark/unmark a reminder on the selected programme. You can set up to a maximum of 10 reminders. > The TV will wake up automatically or display a message when the programme is about to start. Follow the instructions on screen to watch the programme. 4.
2504.4 en 13-12-2006 08:29 Pagina 39 Multimedia Browser EN The Multimedia browser lets you display pictures and/or movies or play audio files stored on a USB device or a memory card. The Multimedia browser application is invoked from the main menu. Your TV is also equipped with the possibility to connect your computer or home network and to access and view your personal multimedia files. See the supplied separate Connected Planet guide for further explanation of this functionality.
2504.4 en 13-12-2006 08:29 Pagina 40 Multimedia Browser (Continued) EN To remove the Memory card/USB device CF 1. Press the MENU/BROWSE key on the remote control to switch off the main menu. 2. Remove the Memory card/USB device. Compact Flash I & II / Micro Drive Memory Stick MultiMedia Card / SD Card Smart Media Card Card data protection • Do not remove the card/USB device when the content is being read or when browsing. Such action may damage the memory card/USB device.
2504.4 en 13-12-2006 08:29 Pagina 41 Multimedia Browser (Continued) Television Multimedia Browser menu TV menu TV channels Programme guide Multimedia Media servers USBDevice 1 Picture Music London 2005 Picture The Beatles Video Xmas2004.alb arnold.jpg USBDevice 1 Picture London 2005 London2005 pic001.jpg The Beatles pic002.jpg Xmas2004.alb pic003.jpg arnold.jpg pic004.jpg USBDevice 1/Picture/London2005 London2005 pic001.jpg pic001.jpg pic002.jpg pic003.jpg pic004.
2504.
2504.4 en 13-12-2006 08:29 Pagina 43 Teletext EN Note:Teletext is not available via equipment connected to the HDMI connector. Most TV channels broadcast information via teletext. This TV has a 1200 pages memory that will store most broadcasted pages and subpages to reduce waiting time. After each programme change, the memory is refreshed. < a Press b to switch the teletext on. > The main index page appears on the screen.
2504.4 en 13-12-2006 08:29 Pagina 44 Teletext (Continued) EN Hypertext With hypertext you can quickly jump to a pagenumber or search for a specific word shown on the current teletext page. a 1. Press the OK key to highlight the first word or a number on the page. 2. Use the cursor up/down, left/right to select any other word or number you want to search for. 3. Press the OK key to confirm.The search starts.
2504.4 en 13-12-2006 08:29 Pagina 45 Teletext (Continued) EN Digital text (only for UK) Some digital channels offer dedicated digital text services (for example BBCi). 1. Press b to switch Digital text on. Note: UK only: Digital text is displayed when programmes are carrying digital text or interactive services. a 2. To use the digital text, follow the instructions on screen. 3.
2504.4 en 13-12-2006 08:29 Pagina 46 To make video and audio connections EN Tip: use the inputs that are available on your equipment that provide the best video or audio performance, as below. Note: your TV comes with all types of connectors with the exception of the DVI connector but some of your equipment may be equipped with this type. In this case you'll need a DVI to HDMI adapter or a HDMI to DVI cable and separate audio cables, all available at your local dealer.
2504.4 en 13-12-2006 08:29 Pagina 47 To make video and audio connections - Side panel overview EN Camera, Camcorder, Game 1. Connect your camera, camcorder or game as shown. 2. Connect to VIDEO 2 and AUDIO L 3 for mono equipment. For stereo equipment also connect AUDIO R 3. S-VHS quality with an S-VHS camcorder is obtained by connecting the S-VHS cables with the S-VIDEO input 1 and AUDIO inputs 3. 1 3 Warning: do not connect cable 1 and 2 at the same time.
2504.
2504.4 en 13-12-2006 08:29 Pagina 49 Connect a VCR or DVD recorder EN Warning: do not place your recorder too close to the screen as some recorders may be susceptible for signals from the display. Keep a minimum distance of 0,5 m from the screen. With a eurocable ANTENNA CABLE EXT2 EXT1 o ANTENNA EXT2 75 EXT1 EXT 1/2 2 3 1 1. Connect the aerial cables 1 and 2 as shown. 2. Connect the eurocable 3 as shown. 3.
2504.4 en 13-12-2006 08:29 Pagina 50 Connect two VCRs or VCR and DVD recorder EN Note: you can not record signals from equipment connected to the YPbPr input. With eurocables ANTENNA EXT2 1. Connect the aerial cables 1 and 2 as shown. 2. Connect your VCRs or DVD-recorder to EXT1 and 2 with the eurocables 4 and 5. 3. Select the equipment you have connected in the Installation menu, Select your connections, p. 33 and link it to EXT1 or 2.
2504.4 en 13-12-2006 08:29 Pagina 51 Connect a DVD player, HD receiver or game console EN Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys. With a HDMI connector HDMI 1/2 HDMI is the leading new standard for Digital video and audio interconnection. o o o o HDMI 1 HDMI 2 AUDIO IN L/R PC-VGA 1. Connect your equipment with the HDMI connector. 2. Select the equipment you have connected in the Installation menu, Select your connections, p.
2504.4 en 13-12-2006 08:29 Pagina 52 Connect a DVD player, a satellite receiver or HD receiver EN Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys. AUDIO OUT With Component Video Connectors DISPLAY SYNCHRONIZED R AUDIO OUT L R AUDIO IN L DIGITAL AUDIO OUT DIGITAL AUDIO IN Y Pb Pr 2 HDTV & Progressive 480p, 576p, 720p, 1080i EXT3 EXT3 : AUDIO IN R/L DIGITAL AUDIO IN EXT3 : YPbPr 1 3 1.
2504.
2504.4 en 13-12-2006 08:29 Pagina 54 Personal computer to the home network connector EN NETWORK DIGITAL AUDIO IN1 IN2 Pr Pb OUT Y Your TV is equipped with the possibility to connect to your computer or home network. See the supplied separate Connected Planet guide for further explanation of this functionality.
2504.4 en 13-12-2006 08:29 Pagina 55 Use the Common Interface slot EN Warning: switch off your TV before any module is inserted in the Common Interface slot. Note: this functionality is only available in certain countries. o COMMON INTERFACE ETHERNET COMMON INTERFACE o o o o HDMI 1 HDMI 2 TOP To receive scrambled DTV signals you will need a CA (Conditional Access) module and a Smart card provided by the service provider. A CA module can enable additional services, for example Pay TV.
2504.4 en 13-12-2006 08:29 Pagina 56 Select connected equipment EN a Before operating your connected equipment you have to make a selection in the Installation, Select your connections menu, p. 33. 1. 2. 3. 4. 5. 6. 7. Press the MENU/BROWSE key. Select TV menu and press the cursor right. Select Installation. Press the cursor right. Select Connections. Press the cursor right. Select the input to which the peripheral equipment is connected. 8.
2504.4 en 13-12-2006 08:29 Pagina 57 Audio- and video equipment keys EN Most of the audio and video equipment from our range of products can be operated with the remote control of your TV. Press one of the keys after you pressed one of the mode keys (DVD, STB, VCR, AUX) according to the equipment you want to operate with this remote control. See Use of the Remote control, p. 5-6.
2504.4 en 13-12-2006 08:29 Pagina 58 EN Troubleshooting Symptom Possible cause/Remedy No picture < Verify if the supplied cables are connected properly. (The aerial cable to the TV, the other aerial to your recorder, the power cables, ..) < Verify if you selected the correct source. < Verify if the child lock has been switched off. Poor picture < Verify in the Manual installation menu if you have selected the correct TV system.
2504.4 en 13-12-2006 08:29 Pagina 59 Troubleshooting (Continued) Symptom Possible cause/Remedy The remote does not function < Verify if the remote is set correctly for the equipment your are using. < Verify if the batteries are not dead. Replace the batteries. EN You can still use the keys at the left side of the TV. < Select TV mode on your remote control.
2504.4 en 13-12-2006 08:29 Pagina 60 Annex 1 - Philips TV software upgrade with portable memory EN Introduction Philips continuously tries to improve its products and it wants you to profit of that even after your purchase. Therefore it allows you to upgrade your TV software using a USB memory device (not supplied). You can execute the software upgrade procedure yourself. Verifying the version of the TV software TV menu Installation Software upgrade Current softw. info .............
2504.4 en 13-12-2006 08:29 Pagina 61 Annex 1 (Continued) EN Upgrade the TV software Software Upgrade Application Upgrade busy... Software Id: TL32E-234 Loading Done Validating Done Programming 1. Switch off your TV and remove all memory devices. 2. Insert the USB portable memory that contains the downloaded software upgrade. 3. Switch on your TV with the power key B at the side of the TV. 4. The upgrade process starts automatically.
2504.4 en 13-12-2006 EN 08:29 Pagina 62 Annex 1 (Continued) Local software upgrade procedure TV menu Installation Software upgrade Current softw. info ............. Local upgrades Channels Manual network i.. Announcement Preferences Connections Decoder Factory settings Software upgrade Info New software, or the currently installed software version, can also be obtained from the www.philips.com/support website. 1. Go to www.philips.com/support using the web browser of your PC. 2.
2504.4 en 13-12-2006 08:29 Pagina 63 Annex 2 - Philips TV-Slideshow Format with background music Notes: - the latest version of this document can be found on the Philips support website (www.philips.com/support). Use the type number of your TV to find this documentation and other related files. - Philips can’t be held responsible for any problems that may occur as a result of the content in this document.
2504.4 en 13-12-2006 08:29 Pagina 64 EN Annex 2 (Continued) Supported XML-tags The following table gives a description of the XML syntax. Tag Name Use philips-slideshow mandatory Description Philips slideshow signature including the version. title optional The title of the playlist. audio optional The audio-URL following this tag will define the music playing in the background during the slideshow. A single song or playlist (.m3u & .pls) are the only valid audio references.
2504.4 en 13-12-2006 08:29 Pagina 65 Annex 3 - Philips TV - Portable memory and USB issues EN Notes: - the latest version of this document can be found on the Philips support website (www.philips.com/support); - the software of your TV is upgradeable. If you have problems first check if you have the latest software installed on your TV. The latest software, together with instructions, can be found on the Philips support website.
2504.4 en 13-12-2006 08:29 Pagina 66 Annex 4 - Issues referring to connected peripherals with a HDMI connector EN The HDMI IN connector allows the following TV and monitor display modes: HD Standard Definition TV (SDTV) Enhanced Definition TV (EDTV) 640x480p 720x480p 720x576p High Definition TV (HDTV) 1920x1080i 1280x720p PC VGA SVGA XGA - 640x480i 720x480i 720x576i 640x480 800x600 1024x768 If necessary, you can adjust the picture position to the centre of the screen with the cursor keys.
2504.4 en 13-12-2006 08:29 Pagina 67 Index active control ........................... 18 ambilight......................................21 analogue: manual installation . 30 antenna......................................... 4 audio receiver .......................... 54 audio equipment keys............. 57 auto format............................... 18 automatic installation.............. 29 avl (audio volume leveller)..... 20 balance ....................................... 19 batteries ..................
2504.4 en 13-12-2006 08:29 Pagina 68 Recycling EN Recycling Disposal of batteries R The packaging of this product is intended to be recycled. Apply to the local authorities for correct disposal. The batteries supplied do not contain the heavy metals mercury and cadmium. Please check on how to dispose of exhausted batteries according to local regulations.
2492.3 EN 24-02-2006 15:55 Pagina 1 GB Contents What is Connected Planet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What you need to enjoy Connected Planet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 1: Installing the Philips Media Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2492.3 EN 24-02-2006 15:55 Pagina 2 Step 1: Installing the Philips Media Manager (PMM) & Insert the supplied CD into your computer’s CD drive. If the CD does not start automatically, double-click My Computer, then the CD-ROM drive icon and finally start.htm to start the CD. é Please select your language, click on Install Media Manager and follow the on-screen instructions.
2492.3 EN 24-02-2006 15:55 Pagina 3 Adding files in the Philips Media Manager (PMM) & Select the PMM from your Windows Start-menu or double-click on the PMM symbol in the task bar. é Click on Music, Pictures or Movies at the top of the PMM window. “ Select Add Music, Add Pictures or Add Movies. ‘ Click on Add Files or Folders... . ( Select a folder or one or more media files and click on Open to add the selected folder or files to the Media Manager window.
2492.3 EN 24-02-2006 15:55 Pagina 4 Step 2: Identifying your PC configuration We will focus on the two main PC configurations found in modern households today. OR Configuration A Configuration B If feasible we advise to set up a router-based network as described in Configuration A before connecting your TV.
2492.3 EN 24-02-2006 15:55 Pagina 5 Step 3: Connecting and configuring your TV Configuration A Make sure DHCP/Auto IP (automatic network addressing) is enabled on your router and your PCs. On most of the recently purchased PCs and routers, automatic network addressing is already enabled. You can check this on your PC with the Network Utility on the supplied CD. Connecting your TV & Push one end of an Ethernet cable (a straight cable) into the NETWORK connector at the bottom of the TV.
2492.3 EN 24-02-2006 15:55 Pagina 6 Step 4:Viewing multimedia content Make sure the PC with Philips Media Manager installed on it (see p. 2) is switched on. & Switch on your TV. é Press the BROWSE/MENU key on the remote control to display the Browse menu. “ Select your PC from which you want to access the content and press the cursor right.