Register your product and get support at www.philips.
26 26 27 27 28 28 30 Back connectors Side connectors Connect a computer Assign devices Use Philips EasyLink Use a Kensington lock 1 Notice 2 2 Important 3 3 Your product 5 5 5 8 Product information 31 9 Troubleshooting 33 7 7 7 8 8 10 Index 35 Side controls and indicators Remote control 4 Use your product Switch your TV on/off or to standby Switch channels Watch connected devices Adjust TV volume 5 Use your product in digital mode Understand the information banner Install channels Test digi
1 Notice 2009 © Koninklijke Philips Electronics N.V. All rights reserved. Speci cations are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
• Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply. Safety • Risk of electric shock or re! • Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use.
• • • • • • the value printed on the back of the TV. Never connect the TV to the power outlet if the voltage is different. Risk of injury, re or power cord damage! Never place the TV or any objects on the power cord. To easily disconnect the TV power cord from the power outlet, ensure that you have full access to the power cord at all times. When you disconnect the power cord, always pull the plug, never the cable. Disconnect the TV from the power outlet and aerial before lightning storms.
Remote control E n glish 3 Your product Congratulations on your purchase, and welcome to Philips! To fully bene t from the support that Philips offers; register your product at www.philips.com/welcome. 28 1 2 27 3 26 Side controls and indicators 25 24 4 4 5 6 7 8 9 3 23 2 1 a POWER: Switches the product on or off. The product is not powered off completely unless it is physically unplugged. 22 16 17 18 b P/CH +/-: Switches to the next or previous channel.
b DIGITAL MENU Accesses or exits the digital menu. s 0-9 (Numeric buttons) Selects a channel or setting. c t PICTURE (Smart picture) Launches the picture menu. d SUBTITLE Enables or disables subtitles. u SOUND (Smart Sound) Launches the sound menu. e DUAL Switches Stereo and Nicam Stereo to Mono. Selects rst language (Dual I) or second language (Dual II) in bilingual programmes. v +/- ( Volume +/-) Increases or decreases volume. w BACK A/CH Returns to a previous screen.
Switch channels E n glish 4 Use your product This section helps you perform basic operations. Switch your TV on/off or to standby • To switch on • If the standby indicator is off, press POWER at the side of the TV. • If the standby indicator is red, press (Standby-On) on the remote control. To switch to standby • Press (Standby-On) on the remote control. » The standby indicator switches to red. • • • Press BACK A/CH on the remote control to return to the previously viewed channel.
Watch connected devices Adjust TV volume Note • For easy access, add new devices to the home menu before selecting them. Use the source button 1 Press SOURCE . » The source list appears. 2 Press or device. 3 Press OK to watch the connected device. to select the connected Use the home menu Note • You can add new devices to the home menu for easy access . 1 Press (Home). » The home menu appears. 2 3 Press 8 to select the device. Press OK to watch the connected device on your TV.
Understand the information banner When you select a digital channel, an information banner is displayed at the top of the screen. The banner disappears after a few seconds. The information banner provides useful information on the current programme on the screen such as channel name, program title, start time of programme, and so on. Install channels The rst time you set up your TV, you are prompted to select a menu language and to install TV and digital radio channels (if available).
» A search begins. Any new channels are added to the channel list menu. The percentage of the installation that has been completed and the number of channels found is displayed. Note 5 Install digital channels manually You can manually install digital services by keying the channel number. • To cancel installation, press OK . 4 When the search is complete, press OK to accept the new services. 5 Press to return to the previous menu or press to exit.
7 Press to return to the previous menu or press DIGITAL MENU to exit. Tip • If the signal strength is poor, consider adjusting or checking the connection of your antenna. Contact a professional antenna installer for best results. Set your preferences E n glish » An indicator bar displays the strength level of the TV signal. Set your language You can select your preferred language for system menu and subtitle. Note • If you are not in the digital mode, press ANALOG/DIGITAL .
Set your digital audio output • If Enable Pin Protection is Off, select On to Note proceed. • If you are not in the digital mode, press ANALOG/DIGITAL . 1 Note Press DIGITAL MENU to display the onscreen menu and select [Preferences] > [Digital Audio Output] and press . 2 Press or output. 3 Press to return to the previous menu or press DIGITAL MENU to exit. 2 Enter the default PIN code “1234” with the numeric buttons (0-9). You can access the menu now using the default PIN code.
Add all services to a favourite list 1 Press DIGITAL MENU to display the on-screen menu and select [Favorites] > list number (List 1 to List 4) > [Add all services]. 2 3 Press 4 Press to return to the previous menu or press DIGITAL MENU to exit. You can create a list of up to four of your favourite TV channels and radio stations. Note • If you are not in the digital mode, press ANALOG/DIGITAL .
Use the Electronic Programme Guide EPG is an on-screen guide available for digital channels. EPG allows you to: • View a list of digital programmes being broadcast • View upcoming programmes • Group programmes by genre • Set reminders when programmes start • Set up preferred EPG channels Switch on EPG 1 When watching TV, press GUIDE . » The EPG planner screen appears displaying information about the scheduled programmes. Tip • Press GUIDE to switch between EPG and channel grid.
• 3 4 Access TV menus Menus help you to install channels, change picture and sound settings and access other features. Press OK to con rm your choice. Press (Home) to exit. Remove devices from the home menu If a device is no longer connected to the TV, remove it from the home menu. 1 Note [Setup]Accesses menus to adjust picture, sound and other TV settings. [Add new device]Adds new devices to the home menu for easy access. Press (Home). » The home menu appears.
Change picture and sound settings Change picture and sound settings to suit your preferences. You can apply pre-de ned settings or change settings manually. Use settings assistant Use the settings assistant to guide you through the best picture settings. 1 Press (Home). » The home menu appears. 2 Press to select [Setup] > [Picture] > [Settings assistant] > [Start]. 3 Press OK . » The [Settings assistant] menu appears. Follow the on-screen instructions to choose your preferred picture settings.
• • • • • • • [Dynamic backlight]Adjusts the brightness of the TV backlight to match lighting conditions. [MPEG artifact reduction] Not available in all models. Smoothes out transitions on digital pictures. You can switch this feature on or off. [Colour enhancement]Makes colours more vivid and improves the resolution of details in bright colours. You can switch this feature on or off. [PC mode]Adjusts picture settings when a PC is connected to the TV.
Use smart sound • Use smart sound to apply pre-de ned sound settings. • • 1 Press SOUND. » The [Smart sound] menu appears. 2 Press to select a smart sound setting: • [Standard]Adjusts sound settings to suit most environments and types of audio. • [News]Applies sound settings ideally suited for spoken audio, such as the news. • [Movie]Applies sound settings ideally suited for movies. • [Personal]Applies the settings that were customised in the sound menu. [Headphone volume]Adjusts headphone volume.
Tip • View all channels before adding a channel to a Use timers E n glish Add a channel to a favourite list You can set timers to switch the TV on or switch to standby at a speci ed time. favourite list. 1 2 3 4 5 6 7 When watching TV, switch to the channel you want to add to a favourite list (see ‘Switch channels’ on page 7 ). Press . » The channel options menu appears. Press to select [Mark as favourite]. Press OK . Set the time 1 2 3 4 5 6 Press (Home). Select [Setup] > [Features] > [Clock].
Automatically switch the TV on (on timer) You can switch the TV to a speci ed channel at a speci ed time, from standby. 1 2 3 4 Press (Home). Lock or unlock the TV Locking the TV prevents your child from accessing all channels and connected devices. 1 2 Select [Setup] > [Features] > [On timer] > [Activate]. Press OK . Press to set the frequency, time and channel. Tip • To switch off [On timer], select [OFF] in the [On timer] menu. Press (Home). Press to select [Setup] > [Features] > [TV lock].
Note View photos, play music and watch video from a USB storage device • When you select a subtitle language on a digital TV channel as described below, the preferred subtitle language set in the installation menu is temporarily overruled. 1 2 3 4 5 Press Caution • Philips is not responsible if the USB storage device is not supported nor is it responsible for damage or loss of data from the device. (Home). Press to select [Setup] > [Features] > [Subtitle language].
5 Press OK to con rm. » The USB content browser appears. 2 Note • If you connect multiple USB storage devices via USB hub, a message appears prompting you to select a device. Press to select the device, then press OK to con rm. Press: • to pause the slide show. • or to go back or move forward to the next image. • BACK A/CH or to stop the slide show and return to the USB content browser. Change slide show settings Tip 1 When viewing a slide show, press OPTIONS . » The slide show options menu appears.
1 2 3 In the USB content browser, press enter the [VIDEO] folder. Press to select a video. to Press OK to play the video. Upload a wallpaper picture from a USB device Before performing this procedure, be sure to have available a USB storage device containing the picture you intend to use as wallpaper. 1 Connect the USB storage device to the TV. » The home menu appears with [Browse USB] already highlighted. 2 3 4 Press OK.
4 Follow the on-screen instructions to download the TV identi cation le to the USB storage device. Note • The TV restarts after the software update is complete. Step 2 Download the latest software 1 2 3 4 Connect the USB storage device to a computer with internet connection. Locate and open the le update.htm on your USB storage device. Read the on-screen instructions and click the Send ID button. If a new software is available, the update is downloaded to the USB storage device.
Follow on-screen instructions to view the demo. 5 Press DEMO to exit. E n glish 4 Reset the TV to factory settings You can restore the default picture and sound settings of your TV. Channel installation settings remain the same. 1 2 Press (Home). Select [Setup] > [Installation] > [Factory settings]. 3 Press to enter the [Factory settings] menu. » [Reset] is highlighted. 4 5 Press OK to reset to default settings. Press (Home) to exit.
7 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start. b AUDIO IN L/R Audio input from devices that require a separate audio connection, such as a computer. c VGA Video input from a computer. Note • Different types of connectors may be used to connect a device to your TV, depending on availability and your needs. d SPDIF OUT Digital audio output to home theatres and other digital audio systems.
1 2 3 4 Connect a computer E n glish Side connectors Before you connect a computer to the TV • Set the monitor refresh rate on your computer to 60Hz. • Press FORMAT and change the TV picture format to [Unscaled]. Connect a computer with one of the following connectors: Note • Connections via DVI or VGA require an additional audio cable. 5 • HDMI cable • DVI-HDMI cable 6 7 a AUDIO IN L/R Audio input from analogue devices connected to VIDEO or S-VIDEO.
HDMI cable and HDMI-DVI adaptor • AUDIO IN: LEFT / RIGHT HDMI 1 / DVI HDMI 2 / DVI HDMI 3 / DVI VGA 6 Switch on your device and check for video and audio output. 7 If there is video and audio output, press OK . Repeat the procedure until all devices are correctly assigned to connectors. Use Philips EasyLink DVI VGA cable • AUDIO IN: LEFT / RIGHT HDMI 1 / DVI HDMI 2 / DVI HDMI 3 / DVI VGA Your TV supports Philips EasyLink, which uses the HDMI CEC (Consumer Electronics Control) protocol.
EasyLink buttons Tip • Press TV to switch back to the aerial source from EasyLink mode. Enable or disable EasyLink Note • Do not enable Philips EasyLink if you do not intend to use it. You can control EasyLink-compliant devices with the following buttons on the remote control of your TV. 1 2 Press Button (Play/ Pause) 3 Select [ON] or [OFF]. EasyLink function Starts, pauses or resumes playback on your EasyLink device. (Stop) Stops playback on your EasyLink device.
4 Select [Auto (EasyLink)]. » TV speakers are set to EasyLink mode. Use a Kensington lock There is a Kensington security slot at the back of the TV. Prevent theft by looping a Kensington lock between the slot and a permanent object, such as a heavy table.
Product information is subject to change without notice. For detailed product information, go to www.philips.com/support.
Power • • • 32 Mains power: AC 220-240V, 50-60Hz (+/- 10%) Standby power: < 0.
This section describes commonly encountered issues and accompanying solutions. General TV issues The TV does not switch on: • Disconnect the power cable from the power outlet. Wait for one minute then reconnect it. • Check that the power cable is securely connected. The remote control is not working properly: • Check that the remote control batteries are correctly inserted according to the +/- orientation. • Replace the remote control batteries if they are at or weak.
The picture does not t the screen; it is too big or too small: Try using a different picture format. • The picture position is incorrect: Picture signals from some devices may • not t the screen correctly. Check the signal output of the device. Sound issues There is a picture but no sound from the TV: Note • If no audio signal is detected, the TV automatically switches the audio output off — this does not indicate malfunction. Check that all cables are properly connected.
E B Batteries 4, 32 C Channel list favourite troubleshooting update Channels favourite list install automatic manual rearrange rename test reception Child lock TV lock Clock Computer format technical speci cations Connections HDMI troubleshooting mains cord technical speci cations troubleshooting USB troubleshooting Connectors assign devices 18 33 19 18 31 31 32 31 10 20 21 31 34 26 31 34 34 28 D Demo Devices assign watch Digital channel test reception Digital radio Display resolution 23 E n glish s
P Picture format troubleshooting Picture settings PIN code Power 33 16 33 33 R Reception Remote control technical speci cations troubleshooting 33 31 33 S Screen saver Settings assistant Sleep timer Smart settings Sound settings Standby troubleshooting Subtitles language on analogue channel on digital channel 23 16 19 16 , 18 18 33 21 20 20 T Technical speci cations Timer on timer sleeptimer standby Transmission troubleshooting Troubleshooting TV adjust volume menu software standby switch channels swi
© 2009 Koninklijke Philips Electronics N.V. All rights reserved.
