Installation Manual for StudioLine xxHFL2839T xxHFL2849T 65HFL2859T Status: Version: Date: Author: Final 1.
1
Contents 1. Requirements before starting the installation.......................................................................................................... 3 2. Find out the state of the TV ...................................................................................................................................... 5 3. Re-install TV ..........................................................................................................................................................
General remark: The UI (User Interface) for the different sets is different, whereas the selectable options in the different menus stay the same. Please have a look to the different examples from the different UIs: e.g.: appearance of the UI for xxHFL2839 & xxHFL2849 e.g.
1. Requirements before starting the installation Before starting the installation, make sure that you have everything you need at hand. Master remote control 22AV8573 or Guest remote control 22AV1407A And USB stick To enter the Hotel TV menu using the guest remote (22AV1407A): For all HFL2839 models you can use the guest remote and the key sequence 3,1,9,7,5,3,MUTE to access the Hotel Mode. The key sequence will not work if High Security Mode is enabled.
2. Find out the state of the TV It is important to know if a TV is in ‘first time installation’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. If you power on the set and then press the ‘Home’ button on the guest remote, you will see this screen appear, if the TV already has been installed or the wizard was already skipped.
Disable the Hotel TV mode To access the setup menu you should press the ‘RC5 SETUP’ key and then press the ‘Home/Menu’ button if you are using the 22AV8573. To access the Hotel TV menu using the guest remote you need to input the key sequence 3,1,9,7,5,3,MUTE . You can use the guest remote to select with the up or down arrow buttons and change values with the left or right arrow buttons. Set the Hotel TV Mode to OFF. Press “MENU” or “Return” button to exit this menu.
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. First step is to set the Hotel Mode to OFF and exit using the MENU or Return button on the guest remote. Note: It is not required to use a save button, once you exit the menu, you will save the settings from the Hotel TV Menu Press the MENU button on the guest remote to access the full menu of the TV. The following menu should be displayed.
If you are sure that you want to re-install the TV, select “Yes” and press OK. TV will reboot itself and show the “virgin state” screens with a welcome message. Note: All settings will be reset to default values except Hotel menu values. Those values will remain the same. To reset the Hotel TV menu use the Reset to Default Values option present in that menu.
4. Installation wizard When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. The installation wizard, from whom this screen is a part, will guide you through all the menus for a basic TV installation. Please select your language and press “OK” to start the installation of the TV set. The first step is to select the country, which will enable country cable providers, time setting and channel list presets.
Press the “MENU” button to quit the channel list and watch TV. (*) LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel sequence (if available). Digital Cable Installation If you want to install DVB-C channels, select the “Digital CABLE” option and press the “OK” button on the remote control to continue. To continue, please select “YES” and press “OK”. To cancel the operation, select “NO” and press “OK”.
Always select the “Home Mode” and press OK to continue. “Store mode” will display banners with commercials while running. Depending on country you might need to follow an additional step, setting up a pin code. This pin code will be used for blocking TV channels and settings. In some cases due the country regulations, you have to provide a pin code formed from four digits. This pin code will be required in case you want to modify the settings of the TV. Selected PIN code cannot be 0000.
Only available while using selection of “First Time Installation” You can select frequency ranges from this screen. For highlighting lines, use the “▼“or “▲” buttons. You can enter the frequency range manually by using the numeric buttons on the remote control. Set the Start and Stop Frequency as desired by using the numeric buttons on the remote control. After this operation, you can set the Search Step as 8000 KHz or 1000 KHz.
Here you can move, edit or lock channels. The information bar displayed on the bottom part of the screen will guide you through the options that you can use. Now you can press “MENU” to exit the installation page or you can press the “OK” button to watch TV. Pressing the MENU button will bring the MENU with all options active. 5. Picture Note: this menu might not be available depending on the settings in the Hotel Mode menu.
The option which can be set: - - Mode: Can be set to one of these options: Cinema, Game, Sport, Dynamic and Natural. Contrast: Sets the difference between the brightest and darkest of the screen. Brightness: Sets the brightness value for the screen. Sharpness: Sets the sharpness value for the objects displayed on the screen. Color: Sets the color value, adjusting the colors. Energy Saving: Can be set to one of these options: Off, Custom, Auto, Maximum, Medium and Minimum.
Select and press “OK” to access the submenu: The options available are: - - Volume: Adjusts the volume level. Equalizer: In the equalizer menu, the preset can be changed to Music, Movie, Speech, Flat, Classic and User. Press the “MENU” button to return to the previous menu. The equalizer menu settings can be changed manually only when the Equalizer Mode is in “User” mode. Balance: This setting is used for emphasizing left or right speaker balance. Headphone: Sets headphone volume.
7. Settings Note: this menu might not be available depending on the settings in the Hotel Mode menu. The submenu can be access by pressing “OK” when this menu is highlighted. The options available are: - The Conditional Access: Controls conditional access modules when available. Language: Configures language settings (-may change depending on the country selected) Preferred and current settings will be available.
- Sources: Enables or disables selected source options. Accessibility: Configures “Hard Of Hearing” and “Audio Description” (Refers to an additional narration track for blind and visually impaired viewers of visual media, including television and movies.) - More: (selecting “MORE” provides an extra menu: Menu Timeout: The amount of time for displaying the menu and can have different values OFF, 15 sec, 30 sec and 60 sec.
Install and Retune Menu Content all options related to channel installation. Note: this menu is not visible when Hotel Mode is set to ON. The menu contains options for automatic channel install, manual channel install, network scan, analog fine tune for a better reception of the analog TV channels. The first time installation option will delete the TV channels and set all settings to default values, except Hotel TV settings. Automatic Channel Scan: Displays automatic tuning options available.
Manual Channel Scan: This feature can be used for direct broadcast entry. Search Type: Type of the channel to install Digital Cable, Digital Aerial or Analog Frequency: Input for the frequency Modulation: select the modulation type Network channel scan: Enable or disable the network scan Signal quality & Signal Level: These two options will show the quality and level of signal received on the frequency defined above. Network Channel Scan: Searches for the linked channels in the broadcast system.
Export Channel List to USB: connect an USB device to the USB port of the set. While pressing the OK button on the RC an XML File will be copied to the USB. This XML file can be used for the CHANNEL EDITOR program (see appendix 1) Import Channel List from USB: import an (prepared) XML file from the USB device First Time Installation: Deletes all stored channels and settings, resets the TV to factory settings and starts the first time installation.
8. Channel list Note: this menu is not visible when Hotel Mode is set to ON. For channels options like: add/remove, edit name, lock/unlock or move you have to access the menu from the picture below. Channel management can also be done with channel editor application available for PC. Check appendix 1 for channel editor installation and usage. Press “OK” for the submenu. Note: If the following menu is not displayed in the menu, please go and disable the Hotel TV mode.
Watch: will display the current selected channel from the channel list Move: will open a new window to enter a new channel number Edit name: will open a new window to edit the name of the channel Lock/Unlock: will open a new window to lock or unlock the current selected channel from the channel list. The PIN is a 4-digit Code. Add/Remove Favourites: will open a new window to create 4 different kind of favorite lists.
9. Media Browser Note: this menu might not be available depending on the settings in the Hotel Mode menu. You can play photo, music, and movie files stored on a USB disk by connecting it to your TV. Connect a USB drive to the USB input located on the side of the TV. TV will read the content and provide an option to browse the USB drive. In Media Browser setting the following items are available: Videos, Photos, Music, All and Settings.
10. Professional Settings [Hotel Mode] Feature to enable or disable the Hotel TV Menu features. Note: When enabled, the TV will follow configured feature settings. If the Hotel Mode is set to OFF, none of the settings from this menu will be active. [Pin8] Feature to enable or disable the auto SCART feature Note: This feature allows a connected SCART device to turn the TV on or off. [Last status] This feature allows the TV to remember the last used configuration and restore when startup again.
[Startup Position] Select startup program/source when TV is switched on via Power On key or Digit keys. • Auto TV wakes up in last used channel/source. • TV: The TV set wakes up with the channel specified in Startup Channel field • SCART / Side AV / HDMI1/ YPbPr / VGA_PC [Startup Channel] Feature to select the startup channel. [Volume Limit] only xxHFL2839 Feature to set the maximum volume level. Selectable values between 0-100.
[OSD Disable] Feature to hide menu items when the Remote Control Menu key is pressed. • Disable All Menus :all menu icons are hidden • Disable Setup Menus: Picture, sound, settings and media browser menu icons are displayed. When [Hotel Mode] is set to Off, all TV menu items will be displayed (picture, sound, settings install and retune, channel list, media browser). If OSD Disable is set to Disable All Menus, the EPG will not be displayed. [Teletext] Feature to hide the Teletext display.
[Wakeup Time Channel] This feature helps to select the channel to extract the reference time to synchronize with for setting the Wakeup Time. • Use the digits button(s) on the remote to complete the entry field All timers and events are not possible to set once all menus are hidden. [Wakeup Time Volume] Feature to set the wakeup time volume level. Selectable values between 0-100. [USB option] Feature to detect if a USB device is connected. - ON: to enable USB device detection.
[Multiple RC support] Feature to enable the Multi RC. • Off: feature is disabled • On: feature is enabled and shows which RC is set Note: see chapter 13 for more information [Welcome Screen] Feature to show a welcome screen at startup • On: a welcome screen is shown • Off: a welcome screen is hidden Note: see chapter 11 for more information [NIT Update] If this option is enabled LCN information’s will be updated automatically. This option is available only for Nordic countries.
[CEC Enabled] To control the behavior of the CEC break-in Off: CEC is disabled On - Auto switch: TV will automatically switch to the device sending the control command On – Manual switch: CEC is enabled, but TV will not switch automatically [Reset to Default Values] Highlight this option and press the OK button on the remote to return the TV to default settings. Note: Only Hotel TV options will be affected by this action.
11. Welcome Logo Once this feature is configured and set, the welcome image will be displayed within 14 seconds after switch ON. This page will remain until a key on the RC is pressed. How to upload Welcome Logo 2 possibilities: 1.: Welcome Logo + Clone File 1. Create a graphics file: 960 x 540.png (1920 x 1080.png : only for 65HFL2859) with the logo. Follow the next guidelines: Maximum size of the welcome logo should be less than 1024 Kb. Always use 16 bit color depth. 2. File name: hotel_wel.
12. Clone With cloning it is possible to copy to/from a USB device the configuration data and the channel list data from a TV. Place a USB Memory stick in the USB side connector of the TV. *The USB device should be formatted as FAT or FAT32. Access the Hotel Mode Menu with the RC 8573 (yellow remote) or with the guest remote by entering the key sequence 3,1,9,7,5,3,MUTE and navigate with the TV remote to following items: [Copy from USB] 1. Select [Copy from USB] and press OK. 2.
12.1 Software upgrade and Instant Initial Cloning Software upgrade and cloning can be done without going through the installation wizard. When the installation wizard is displayed, it is possible to directly upgrade the FW or install the TV with a clone file taken from another similar TV. To be able to upgrade you have to have a USB stick plugged in with a valid FW and/or clone file(s) before starting the TV. For xxHFL2839: A valid FW should have VES161HE_upgrade.
5. When the process is complete, the TV will restart and display the switch ON channel. USB flash drive can be removed. TV set is configured. Note: Software upgrade via an USB device can be done anytime by using the hidden key combination, “Menu-1-5-05”.
13. Feature settings [Multi RC] Enter the MultiRC Menu Feature to configure the remote control to work with one TV. To enter the MultiRC Menu on TV press the key sequence: MENU, RETURN, 1,2,3,4. On the TV a menu will guide you to select the desired TV configuration. Choose a number between 1 and 4 to assign to the TV. Afterwards configure the remote control for the same number as TV by keeping pressed MENU (HOME) + Digit for 5 seconds. The HFL2839/HFL2849 supports a maximum value of four remotes.
14. CSM (Consumer Setup menu) Enter Service Menu It is only possible to enter the Service Menu if the Hotel Mode is disabled. Enter the Hotel Mode menu and set the Hotel Mode to “Off” To enter the Service Menu: • Press the following key sequence: Menu, 1,2,3,6,5,4 No items can be selected in the Service Menu. The software version number will be shown as VES161HE_x.y.z (for xxHFL2839) and VES162HE_x.y.z (for xxHFL2849) and VES163HE_x.y.
Appendix 1 Channel List Editor Channel List Editor PC tool enables editing exported XML channel list files in a way that is more understandable and user friendly. Note: XML means Extensible Markup Language Channel list should be exported from a TV set using the option available in the following menu (make sure that Hotel mode is set to OFF): 1. 2. 3. 4. Insert the USB key on side connector of the TV. Enter in the MENU and navigate to Channel list. Select the option “Export Channel list to USB”.
Interface description and usage 1. Main window Main menu consists of pretty much the same options as the toolbar below, with exception of “Save as” and “Exit” option from File submenu. File submenu consists of standard options as it can be seen on ion the Image 1-1 – File Image 1-1 – File Edit submenu consists of controls to Add, Edit and Delete the current selected channels in the list. Image 1-2 – Edit Tools submenu consists of Settings and Preferences (Image 1-2- Tools).
First group from the left provides file operations next to it provides channel managing operations and the last group provides list settings and help. Image 1-3 – Toolbar Clone – clones channel info except for Service name and service number for easy adding channel with similar values. Under tool bar there is a list of channels from the loaded list sorted by network type in a tree view. More than one channel can be selected by holding SHIFT or CTRL and right mouse click.
Image 1-6 - Common Service Params And, depending on the Network Type of the currently selected channel, different additional groups can be displayed: Image 1-7 - DVB Triplet Values in DVB Triplet are only present when DVB channels are selected, for Analogue channels values in this group are empty. Image 1-9 - DVB-C When the form is in add/edit state new buttons are added under “Tuner Configuration” group: Image 0-8 - Edit state 2.
Image 2-1 - Add Add – changes the state of the main form to add state and empty’s all the fields so the user can enter new values. Only when in add state Network Type combo box is enabled. When correct values are entered user can save with pressing “Enter” key or pressing “Add” button. Image 2-2 – Clone Clone - is much like Add just instead of leaving all the fields empty it leaves all the values from the previously selected channel except for values that needs to be unique (Service Name, Channel Number...
Image 2-3 – Edit Edit – enables editing of the currently selected channel info. When correct values are entered user can save with pressing “Enter” key or pressing “Save” button. Channel or selection of channels can be moved using drag and drop. Move will cause renumbering of the channels in the list. Delete – removes the channel from the list. When single service channel is selected on delete message appears asking the user to confirm deletion of the channel with the corresponding name.
Channel number or LCN can take values from 1 – 9999 as it is defined in code. These limitations are applied in the editor. Save – when the channel list is according with the requirements press “Save” button for saving the channel list. This option will rewrite the open file and save it in the same location. If you want to save the file in to another location please use the “Save As” option from File menu. 3.
© 2016 Koninklijke Philips N.V. All Rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips N.V. or their respective owners. www.philips.