- 2524.3._en.qxd 22-03-2007 15:13 Pagina 1 About this User Manual EN This manual contains all information you will need to initially install and operate your new TV. Also read the help texts which are being displayed at the bottom of the screen. If this instruction manual does not give an answer or if ‘Troubleshooting’ does not solve your TV problem, you can call your Local Philips Customer or Service Centre. See the supplied Worldwide guarantee booklet. 
- 524.3._en.qxd 22-03-2007 15:13 Pagina 2 Safety warnings EN General Do not insert the power plug in a wall socket or hang the TV to the wall before all connections are made. • Place or hang the TV wherever you want, but make sure that air can circulate freely through the ventilation slots. • TV channel logo: present a problem if they are bright and stationary. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 3 Getting started EN Before you start Warning: do not insert the mains cord into the mains at the bottom of the TV and in a wall socket or hang the TV on the wall before all connections are made. Before you switch on your TV, connect all your peripheral equipment. See To make video and audio connections, p. 43. Overview of the rear connector panel There is a wide range of audio and video equipment that can be connected to your TV. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 4 Getting started (Continued) EN Overview of the side connector panel - To connect a camera, camcorder or game, see To make video and audio connections, p. 44. USB - To connect a headphone, see To make video and audio connections, p. 44. - To connect a USB device, see Multimedia browser, p. 37. Connect the antenna < Insert the aerial plug firmly into the aerial socket x at the bottom of the TV. Tip: for best quality use the suppressor cable supplied. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 5 Use of the remote control RC4401/01 EN B Standby Press to switch the TV from or to standby mode. When switched to standby, a red indicator on the TV lights up. Attention: the TV is never powered off completely unless it is physically unplugged. TV Press to select TV mode. DVD STB VCR AUX Press one of these keys to set your remote control to operate a peripheral device. See Audio and Video equipment keys, p. 54. DEMO Press to switch the Demo menu on or off. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 6 Use of the remote control RC4401/01 (Continued) EN +P- Channel selection - to browse through the TV channels and sources stored and marked in the Favourite channels lists; - to select a page in Teletext mode; - to quickly browse through the lists in the menus; - to switch the TV on from standby mode. 0/9 Digit keys To select a TV channel between 0 and 999. AV Select your peripherals See Installation menu, Select your connections, p. 32. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 7 Use of the OPTION key EN The OPTION key allows you to display the Quick access menu which will give you direct access to some features and menu options. 1. Press the OPTION key. > The Quick access menu appears. 2. Press the cursor up/down to select a menu item. 3. Press the OK key to jump to the selected menu item in the TV menu. (Except for the Clock option). 4. Use the cursor keys to make a selection. 5. Press the OPTION key to exit. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 8 Introduction: Digital TV EN Besides traditional analogue broadcasts, you can also receive digital broadcasts via a roof or loft mounted digital antenna in countries where those signals are available and which are supported by this TV.Verify if the country you are now located and you have selected during the installations (see further), supports digital video broadcasting via antenna. See www.philips. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 9 First time installation (Continued) EN Step 1: select your on-screen language After the Welcome screen you are asked to select a language of the TV's on-screen menus.The text of the header and the info on screen continuously change language. Also the digital audio and subtitle language will be set to the selected menu language. 1. Press the cursor up/down to highlight your language. 2. Press the OK key on the remote control. 3. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 10 First time installation (Continued) EN Step 3: Settings assistant: select your TV settings PHILIPS Installation This will help you to complete the Settings assistant. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 11 How to navigate through the menus EN Introduction A lot of guiding instructions, help texts and messages will be displayed on your TV when you use the menus or when you try to execute an action. Read the help texts which are being displayed on the specific item highlighted. The colour keys at the bottom of the screen refer to the different actions which may be executed. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 12 How to navigate through the menus (continued) EN TV menu TV settings Features Installation Info TV settings Settings assistant Reset to standard Picture Sound Ambilight 4. Use the cursor up/down to select a menu item. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 13 Use of the TV menu settings Television TV menu Channel list Programme guide EN The TV menu allows you to access and change settings and preferences in case you want to change the First time installation settings and/or you want to control the settings of special TV functions, features and peripheral equipment. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 14 Use of the TV menu settings (continued) EN B. Use of the Standard settings (if present) This allows you to reset your settings for viewing and listening to predefined factory settings. TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Reset to standard Current Natural Vivid Subtle 1. Select Reset to standard and press the cursor right. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 15 Adjust picture menu settings TV menu TV settings Features Installation TV settings Settings assistant Reset to standard Picture Sound Ambilight EN The picture menu contains the settings that affect the quality of the picture. 1. Press the MENU/BROWSE key on the remote control. > The main menu appears. 2. Select TV menu and press the cursor right. > The TV menu is moved to the left. 3. Select TV settings and press the cursor right. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 16 Adjust picture menu settings (Continued) EN TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Picture ............. Custom tint Pixel Plus Digital Natural Mo.. Dynamic contrast DNR ............. Custom tint (only when Tint is set to Custom) Fine tunes the white point (WP) and black level (BL) of the picture. 1. Select Custom tint and press the cursor right. 2. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 17 Adjust picture menu settings (Continued) TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Picture ............. DNR MPEG artefact red. Colour enhancem.. Active control Light sensor Picture format Info EN MPEG artefact reduction MPEG artefact reduction On smoothens the transitions on digital content. < Select On or Off. Colour enhancement Automatically controls green enhancement and blue stretch. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 18 Adjust sound menu settings EN TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Sound Equalizer Volume Balance Digital audio lang.. Dual I/II Mono/Stereo ............. Info The sound menu contains the settings that affect the quality of the sound. 1. Press the MENU/BROWSE key on the remote control. > The main menu appears. 2. Select TV menu and press the cursor right. > The TV Menu is moved to the left. 3. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 19 Adjust sound menu settings (Continued) Dual I/II TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info EN Sound ............. Mono/Stereo Surround mode Headphone volume AVL Delta volume Auto surround Allows you to select, per channel, Dual I or II, when dual sound transmission is available. Mono/Stereo Allows you to select, per TV channel, Mono or Stereo sound when stereo broadcasts are available. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 20 Enjoy Ambilight EN TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Ambilight Ambilight Brightness Mode Colour Custom colour Separation ............. The ambilight menu contains the settings for controlling the ambient lighting. Using ambient light gives a more relaxed viewing experience and improves perceived picture quality. Analysis of the picture content adapts the colours continuously. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 21 Enjoy Ambilight (Continued) EN Mode Allows you to choose for constant background lighting or for background lighting that matches the images displayed on the screen. TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Info Ambilight ............. Mode Colour Custom colour Separation Balance < Use the cursor keys to select Colour, Relaxed, Moderate or Dynamic. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 22 Enjoy Ambilight (Continued) EN Custom colour TV menu TV settings Settings assistant Reset to standard Picture Sound Ambilight Ambilight ............. Mode Colour Custom colour Separation Balance Note: only available when Custom has been selected in the Colour menu. < < Allows you to customise the ambilight colour. Select Palette to select the general colour of the light output. Select Saturation to adjust the colourfulness of the light. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 23 Adjust feature menu settings EN The Features menu allows you to control the settings of special TV functions, features and accessory equipments. TV menu TV settings Features Installation Info Features Subtitle Digital subtitle lan.. Sleeptimer Childlock Set/Change code On timer ............. 1. Press the MENU/BROWSE key on the remote control. > The main menu appears. 2. Select TV menu and press the cursor right. > The TV Menu is moved to the left. 3. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 24 Adjust feature menu settings (Continued) EN TV menu TV settings Features Installation Features ............. Sleeptimer Childlock Set/Change code On timer Common interface Demo Sleeptimer This sets a time period after which the TV automatically switches to standby. 1. Select Sleeptimer. 2. Press the cursor right. 3. Select a value with the cursor up/down. > The list will have values from 0 to 180 minutes.When 0 is selected, the sleeptimer is switched off. 
- 24.3._en.qxd 22-03-2007 15:13 Pagina 25 Adjust feature menu settings (Continued) TV menu TV settings Features Installation Info Features ............. Sleeptimer Childlock Set/Change code On timer Common interface Demo EN Set code/Change code This allows you to set or change the personal 4-digit access code that is used in the different lock functions of the TV. < < Select Set or Change code. > If no PIN-code exists yet, the menu item is set to Set code. Follow the instructions on screen. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 26 Adjust feature menu settings (Continued) EN TV menu TV settings Features Installation Features Common interface Note: this functionality is only available in certain countries. ............. Sleeptimer Childlock Set/Change code On timer Common interface Demo This allows you to access common interface applications defined by the service provider of the Common Interface (CI) module. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 27 How to search for and store TV channels EN Tip: you will need this chapter only if you want to change the installation settings. Installation menu Television TV menu Channel list Programme guide Multimedia TV menu TV settings Features Installation Installation Languages Country Time zone Channels Preferences Connections ............. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 28 How to search for and store TV channels (Continued) EN TV menu TV settings Features Installation Installation Languages Country Time zone Channels Preferences Connections ............... Select your country This allows you to select the country where you are now located. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 29 How to search for and store TV channels (Continued) Digital: test reception (only with Digital TV broadcasting) TV menu Installation Languages Country Time zone Channels Preferences Connections Decoder ............. EN Channels Autom. installation Installation update Digital: test recept.. Analogue: manual.. Rearrange This allows you to see the quality and the strength of the signal reception for a digital frequency. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 30 Rearrange the channel number list EN TV menu Installation Languages Country Time zone Channels Preferences Connections Decoder ............. Channels Autom. installation Installation update Digital: test recept.. Analogue: manual.. Rearrange < Reshuffle 1. 2. 3. Info This allows you to rename, to reshuffle and to uninstall or reinstall the stored channels. Press the corresponding colour keys and follow the on screen instructions. 4. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 31 Set your preferences TV menu Installation ............. Time zone Channels Preferences Connections Decoder Factory settings Software upgrade Info Preferences Location Teletext 2.5 OSD Programme title EN This menu contains items that can set or adjust various special TV functions and that will typically be accessed only occasionally. Select your location This allows you to select the location of your TV. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 32 Select your connections EN TV menu Installation ............. Time zone Channels Preferences Connections Decoder Factory settings Software upgrade Connections EXT1 EXT2 EXT3 HDMI 1 HDMI 2 Side DIGITAL AUDIO IN Info This allows you to select the peripheral equipment you have connected to the audio and video connectors. 1. Select Connections. 2. Press the cursor right. 3. Select the input to which the peripheral equipment is connected. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 33 Reset the Factory settings TV menu Installation EN This allows you to reset most of the predefined factory states. Factory settings 1. Select and press the cursor right. 2. Press the OK key to erase settings and reset them to their default values. ............. Reset Time zone Channels Preferences Connections Decoder Factory settings Software upgrade Info How to upgrade the TV software TV menu Installation Software upgrade Current softw. info ............. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 34 Create your favourite list EN This allows you to select up to four favourite channels lists with your preferred TV channels and radio stations. For example, each member of your family can create his/her own favourite list. In addition to the favourite channel lists you may also select a list with only digital TV channels or a list with only the radio channels or a list with only the analogue channels. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 35 Create your favourite channels list (Continued) EN To select only TV or only radio channels on the All channels list When the All channels list is displayed or selected you may filter the list and select a list with only the TV channels or a list with only the radio channels. 1. Press the FAV key. > The last selected channel list appears. 2. Press the cursor left. 3. Select the All channels list and press the cursor right. 4. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 36 EPG (Electronic Programme Guide) (Continued) EN a a 2. Press the green colour key on the remote control to watch/listen to the selected programme currently on air. 3. Press the red colour key to mark/unmark a reminder on the selected programme. You can set up to a maximum of 10 reminders. > The TV will wake up automatically or display a message when the programme is about to start. Follow the instructions on screen to watch the programme. 4. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 37 Multimedia Browser EN The Multimedia browser lets you display pictures or play audio files stored on a USB device.The Multimedia browser application is invoked from the main menu. -Following file formats can be reproduced: for pictures: JPEG for audio: MP3, MP3 Pro, LPCM - Only FAT/DOS-formatted memory devices are supported. - Philips can not be held responsible if your USB device is not supported. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 38 Multimedia Browser (Continued) EN Television Multimedia Browser menu TV menu Channel list Programme guide Multimedia USBDevice 1 Picture Music London 2005 Picture The Beatles Xmas2004.alb arnold.jpg USBDevice 1 Picture London 2005 London2005 pic001.jpg The Beatles pic002.jpg Xmas2004.alb pic003.jpg arnold.jpg pic004.jpg USBDevice 1/Picture/London2005 London2005 pic001.jpg pic001.jpg pic002.jpg pic003.jpg pic004. 
- 2524.3._en. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 40 Teletext EN Note:Teletext is not available via equipment connected to the HDMI connector. Most TV channels broadcast information via teletext. This TV has a 1200 pages memory that will store most broadcasted pages and subpages to reduce waiting time. After each programme change, the memory is refreshed. < Press b to switch the teletext on. > The main index page appears on the screen. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 41 Teletext (Continued) EN Hypertext With hypertext you can quickly jump to a pagenumber or search for a specific word shown on the current teletext page. a 1. Press the OK key to highlight the first word or a number on the page. 2. Use the cursor up/down, left/right to select any other word or number you want to search for. 3. Press the OK key to confirm.The search starts. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 42 Teletext (Continued) EN Digital text (only for UK) Some digital channels offer dedicated digital text services (for example BBCi). 1. Press b to switch Digital text on. Note: UK only: Digital text is displayed when programmes are carrying digital text or interactive services. a 2. To use the digital text, follow the instructions on screen. 3. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 43 To make video and audio connections EN Tip: use the inputs that are available on your equipment that provide the best video or audio performance, as below. Note: your TV comes with all types of connectors with the exception of the DVI connector but some of your equipment may be equipped with this type. In this case you'll need a DVI to HDMI adapter or a HDMI to DVI cable and separate audio cables, all available at your local dealer. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 44 To make video and audio connections - Side panel overview EN Camera, Camcorder, Game USB 2 3 1 1. Connect your camera, camcorder or game as shown. 2. Connect to VIDEO 2 and AUDIO L 3 for mono equipment. For stereo equipment also connect AUDIO R 3. S-VHS quality with an S-VHS camcorder is obtained by connecting the S-VHS cables with the S-VIDEO input 1 and AUDIO inputs 3. Warning: do not connect cable 1 and 2 at the same time. 
- 2524.3._en. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 46 Connect a VCR or DVD recorder EN Warning: do not place your recorder too close to the screen as some recorders may be susceptible for signals from the display. Keep a minimum distance of 0,5 m from the screen. EXT2 EXT 1/2 EXT1 CABLE 1 o o DIGITAL OUT AUDIO o ANTENNA L o AUDIO OUT o R DIGITAL AUDIO IN 75 3 2 With a eurocable 1. Connect the aerial cables 1 and 2 as shown. 2. Connect the eurocable 3 as shown. 3. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 47 Connect two VCRs or VCR and DVD recorder EN Note: you can not record signals from equipment connected to the YPbPr input. EXT2 With eurocables EXT1 EXT 1/2 CABLE o o ANTENNA 75 DIGITAL AUDIO IN L o AUDIO OUT o R 3 o DIGITAL OUT AUDIO With aerial cables only 4 1 5 2 RECORDER 1. Connect the aerial cables 1 and 2 as shown. 2. Connect your VCRs or DVD-recorder to EXT1 and 2 with the eurocables 4 and 5. 3. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 48 Connect a DVD player, HD receiver or game console EN Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys. With a HDMI connector HDMI 1/2 o o HDMI 1 HDMI 2 o DIGITAL OUT AUDIO o o ANTENNA DIGITAL AUDIO IN 75 L o AUDIO OUT o R HDMI is the leading new standard for Digital video and audio interconnection. 1. Connect your equipment with the HDMI connector. 2. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 49 Connect a DVD player, a satellite receiver or HD receiver EN Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys. With Component Video Connectors Y Pb Pr G B R AUDIO L/R V H 1. Connect the three separate component video cables 1 to the YPbPr jacks on the DVD player and to the Y, Pb and Pr jacks of EXT3 on the TV. 2. 
- 2524.3._en. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 51 Connect a Home Cinema amplifier Y Pb Pr G B R AUDIO L/R V H Digital Home Cinema amplifier < EXT3 EXT2 EN EXT1 Connect a digital Home Cinema amplifier to the DIGITAL AUDIO OUT connector 1 at the bottom of the TV. Tip: to avoid visible delay between picture and sound, use this DIGITAL AUDIO OUT connector to connect your Home Cinema amplifier. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 52 Use the Common Interface slot EN Warning: switch off your TV before any module is inserted in the Common Interface slot. Note: this functionality is only available in certain countries. COMMON INTERFACE COMMON INTERFACE COMMON INTERFACE o o o o HDMI 1 HDMI 2 TOP To receive scrambled DTV signals you will need a CA (Conditional Access) module and a Smart card provided by the service provider. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 53 Select connected equipment a EN Before operating your connected equipment you have to make a selection in the Installation, Select your connections menu, p. 32. Press the MENU/BROWSE key. Select TV menu and press the cursor right. Select Installation. Press the cursor right. Select Connections. Press the cursor right. Select the input to which the peripheral equipment is connected. 8. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 54 Audio- and video equipment keys EN Most of the audio and video equipment from our range of products can be operated with the remote control of your TV. Press one of the keys after you pressed one of the mode keys (DVD, STB, VCR, AUX) according to the equipment you want to operate with this remote control. See Use of the Remote control, p. 5-6. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 55 Troubleshooting Symptom Possible cause/Remedy No picture < Verify if the supplied cables are connected properly. (The aerial cable to the EN TV, the other aerial to your recorder, the power cables, ..) < Verify if you selected the correct source. < Verify if the child lock has been switched off. Poor picture < Verify in the Manual installation menu if you have selected the correct TV system. 
- 2524.3._en.qxd 22-03-2007 EN 15:13 Pagina 56 Troubleshooting (Continued) Symptom Possible cause/Remedy The remote does not function < Verify if the remote is set correctly for the equipment your are using. < Verify if the batteries are not dead. Replace the batteries. You can still use the keys at the right side of the TV. < Select TV mode on your remote control. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 57 Annex 1 - Philips TV software upgrade with portable memory EN Introduction Philips continuously tries to improve its products and it wants you to profit of that even after your purchase. Therefore it allows you to upgrade your TV software using a USB memory device (not supplied). You can execute the software upgrade procedure yourself. Verifying the version of the TV software TV menu Installation ............. 
- 2524.3._en.qxd 22-03-2007 15:13 EN Pagina 58 Annex 1 (Continued) Upgrade the TV software Software Upgrade Application Upgrade busy... Software Id: TL32E-234 Loading Done Validating Done Programming 1. Switch off your TV and remove all memory devices. 2. Insert the USB portable memory that contains the downloaded software upgrade. 3. Switch on your TV with the power key B at the side of the TV. 4. The upgrade process starts automatically. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 59 Annex 1 (Continued) TV menu Installation Software upgrade Current softw. info ............. Local upgrades Time zone Announcement Channels Preferences Connections Decoder Factory settings Software upgrade Info EN Local software upgrade procedure New software, or the currently installed software version, can also be obtained from the www.philips.com/support website. 1. Go to www.philips.com/support using the web browser of your PC. 2. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 60 Annex 2 - Philips TV-Slideshow Format with background music EN Notes: - the latest version of this document can be found on the Philips support website (www.philips.com/support). Use the type number of your TV to find this documentation and other related files. - Philips can’t be held responsible for any problems that may occur as a result of the content in this document. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 61 Annex 2 (Continued) EN Supported XML-tags The following table gives a description of the XML syntax. Tag Name Use philips-slideshow mandatory Description Philips slideshow signature including the version. title optional The title of the playlist. audio optional The audio-URL following this tag will define the music playing in the background during the slideshow. A single song or playlist (.m3u & .pls) are the only valid audio references. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 62 Annex 3 - Philips TV - Digital camera and USB issues EN Notes: - the latest version of this document can be found on the Philips support website (www.philips.com/support); - the software of your TV is upgradeable. If you have problems first check if you have the latest software installed on your TV. The latest software, together with instructions, can be found on the Philips support website. 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 63 Annex 4 - Issues referring to connected peripherals with a HDMI connector Note: teletext will not be available via equipment connected to a HDMI connector. 
- 2524.3._en.qxd 22-03-2007 15:13 EN Pagina 64 Index active control ........................... 17 ambilight .................................... 20 analogue: manual installation . 29 antenna......................................... 4 audio receiver .......................... 51 audio equipment keys............. 54 auto format............................... 17 automatic installation.............. 28 avl (audio volume leveller)..... 19 balance ....................................... 18 batteries ......... 
- 2524.3._en.qxd 22-03-2007 15:13 Pagina 65 Recycling Recycling EN Disposal of batteries R The packaging of this product is intended to be recycled. Apply to the local authorities for correct disposal. The batteries supplied do not contain the heavy metals mercury and cadmium. Please check on how to dispose of exhausted batteries according to local regulations.