User manual

ManualsBrandsPhilips ManualsSignage SolutionsSignage Solutions Video Wall Display

www.philips.com/welcome

55BDL1005X

V1.10

User Manual (English)

Summary of content (50 pages)

PAGE 1
55BDL1005X V1.10 www.philips.
PAGE 2
55BDL1005X Safety Instructions Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your display: Operation: • Keep the display out of direct sunlight and away from stoves or any other heat sources.
PAGE 3
55BDL1005X Read and follow these instructions when connecting and using your display: • Unplug the display if you are not going to use it for an extensive period of time. • Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids. • Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.
PAGE 4
55BDL1005X Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
PAGE 5
5BDL1005X Information for U.K. only WARNING - THIS APPLIANCE MUST BE EARTHED. (B) Important: (A) This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows:+ 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
PAGE 6
55BDL1005X China RoHS 电子电气产品有害物质限制使用标识要求 (中国RoHS法规标识要求) 产品中有害物质的名称及含量。有害物质铅汞镉六价铬多溴联苯多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 塑料外框 O O O O O O 后壳 O O O O O O CCFL X X O O O O LED X O O O O O 电路板组件* X O O O O O 底座 O O O O O O 电源线 X O O O O O 其他线材 X O O O O O 遥控器 X O O O O O 零部件名称 LCD panel *：电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路、连接器等。本表格依据SJ/T 11364的规定编制。 O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 标准规定的限量要求以下.
PAGE 7
55BDL1005X 《废弃电器电子产品回收处理管理条例》提示性说明为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品回收处理相关法律法规，将其交给当地具有国家认可的回收处理资质的厂商进行回收处理。娤⌈ 㨢᳸$䵥ᵥ⍿Ʋ◦䏝㯹䉭❁ᳫ濕媣ᵥ⍿⊭侻ᷘ廞ノ㒞䵽䏳ⴰㄮƲ◦店䢋⾃⁳᳉濕⊭侻斾堿䏦ヵ ⪷ⴰㄮ悅⊔⃅⩜⊭圊䕂㉨㑻Ʋ 限用物質及其化學符號單元鉛汞鎘六價鉻多溴聯苯多溴二苯醚 (Pb) (Hg) (Cd) (Cr+6 ) (PBB) (PBDE) 塑料外框 ○ ○ ○ ○ ○ ○ 後殼 ○ ○ ○ ○ ○ ○ 液晶面板－ ○ ○ ○ ○ ○ 電路板組件－ ○ ○ ○ ○ ○ 底座 ○ ○ ○ ○ ○ ○ 電源線－ ○ ○ ○ ○ ○ 其他線材－ ○ ○ ○ ○ ○ 遙控器－ ○ ○ ○ ○ ○ 備考1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。備考2.
PAGE 8
55BDL1005X End-of-Life Disposal Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of. Please find out about the local regulations on how to dispose of your old display from your local Philips dealer. (For customers in Canada and U.S.A.) This product may contain lead and/or mercury.
PAGE 9
55BDL1005X Batteries For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation. Please contact your local authority for details on the collection and recycling schemes. For Switzerland: The used battery is to be returned to the selling point.
PAGE 10
55BDL1005X Table Of Contents 1. Unpacking and Installation........................................................1 1.1. Unpacking..........................................................................................1 1.2. Package Contents.........................................................................1 1.3. Installation Notes..........................................................................1 1.4. Mounting on a Wall.....................................................................
PAGE 11
55BDL1005X 1. Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • Due to the size and weight of this display it is recommended for two people to move it. • After opening the carton, ensure that the contents are complete and in good condition. 1.2.
PAGE 12
55BDL1005X 1.4. Mounting on a Wall To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface that complies with TUV-GS and/or UL1678 standard in North America. Protective Sheet VESA Grid Table Tabletop stand 1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the screen face. 2.
PAGE 13
55BDL1005X 1.5. Mounting in Portrait Position This display can be installed in portrait position. 1. Remove the table stand, if attached. 2. Rotate 90 degrees anticlockwise. The “ ” logo should be bristling when facing the display at the back.
PAGE 14
55BDL1005X 1.6. Operating Instructions of Edge Alignment Kit 1.6.1. Installing Edge Alignment Kit • Before install edge alignment kit, displays must be mounted to video wall frame correctly. • Using “Thumb Screw” for easy installing. • Using “Edge Alignment Kit-1” on adjacent four displays. 2 3 1 4 5 8 7 • 6 Using “Edge Alignment Kit-2” on adjacent two displays. 1 4 2 NOTE: 3 When installing the edge alignment kit, please consult a professional technician for proper installation.
PAGE 15
55BDL1005X 1.7. Using of Edge Finishing Kit (Optional) You could use the edge finishing kit to protect the display and have a better appearance. 1.7.1.
PAGE 16
55BDL1005X 2. Parts and Functions 2.1. Control Panel 9 MUTE INPUT 1 1 2 3 MENU 4 5 [ ] button 9 Use this button to turn the display on or put the display to standby. 2 [MUTE] button 4 [ ] button [ ] button [ ] button [ ] button Move the highlight bar down to adjust the selected item while OSD menu is on.
PAGE 17
55BDL1005X 2.2. Input/Output Terminals 25 24 23 22 21 26 2 1 1 3 18 20 15 8 10 4 5 6 7 9 11 12 13 14 16 17 19 AC IN 14 AC power input from the wall outlet. 2 16 IR IN / 5 17 18 19 7 20 21 22 23 RJ-45 HDMI1 IN / 11 24 USB PORT SPEAKERS OUT Audio output to external speakers. HDMI2 IN 25 OPS SLOT Slot for installing the optional OPS module. DVI IN NOTES: We recommend to use Advantech ARK DS262 or Winmate OMIS-OPS modules. We’ll not guarantee other OPS modules.
PAGE 18
55BDL1005X 2.3. Remote Control 1 [ ] POWER button Turn the display on or put the display to standby. 2.3.1. General functions 2 [PLAY] buttons Control playback of media files. 3 1 [ ] SOURCE button Choose input source. Press [ ] or [ ] button to choose from USB, Network, Internet, SmartCMS, HDMI 1, HDMI 2, DisplayPort, Card OPS, DVI-D, YPbPr, AV, or VGA. Press [ ] button to confirm and exit. 2 4 [ ] HOME button Access the OSD menu. 3 12 4 13 5 14 5 [ ] LIST button No function.
PAGE 19
55BDL1005X 2.3.2. ID Remote Control Press [ID] button. The red LED blinks twice. 1. Press [ID SET] button for more than 1 second to enter the ID Mode. The red LED lights up. Press the [ID SET] button again will exit the ID Mode. The red LED lights off. You can set the remote control ID when you want to use this remote control on one of several different displays. Press the digit numbers [0] ~ [9] to select the display you want to control. For example: press [0] and [1] for display No.
PAGE 20
55BDL1005X 2.3.3. Inserting the batteries in the remote control The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: 1. Press and then slide the cover to open it. 2. Align the batteries according to the (+) and (–) indications inside the battery compartment. 3. Replace the cover. Caution: The incorrect use of batteries can result in leaks or bursting.
PAGE 21
55BDL1005X 3. Connecting External Equipment 3.1. Connecting External Equipment (DVD/VCR/VCD) 3.1.1. Using COMPONENT video input Audio Out COMPONENT Out (YPbPr) [R] [L] DVD / VCR / VCD [AUDIO IN] [COMPONENT IN] (YPbPr) 3.1.2.
PAGE 22
55BDL1005X 3.1.3. Using HDMI video input DVD / VCR / VCD HDMI Out [HDMI IN] 3.2. Connecting a PC 3.2.1. Using VGA input VGA Out D-Sub 15 pin Audio Out PC [VGA IN] [VGA AUDIO IN] 3.2.2.
PAGE 23
55BDL1005X 3.2.3. Using HDMI input HDMI Out PC [HDMI IN] 3.2.4. Using DisplayPort input DisplayPort Out PC [DisplayPort IN] 3.3. Connecting Audio Equipment 3.3.1.
PAGE 24
55BDL1005X 3.3.2. Connecting an external audio device Audio In Stereo Amplifier [AUDIO OUT] 3.4. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall. 3.4.1. Display control connection Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2.
PAGE 25
55BDL1005X Connect the [RJ-45] connector of DISPLAY 1 to the [RJ-45] connector of DISPLAY 2 (Ethernet Switch). DISPLAY 1 DISPLAY 2 [RJ-45] PC [RJ-45] [RJ-45] [RJ-45] 3.4.2. Digital video connection Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [DVI IN] connector of DISPLAY 2. DISPLAY 1 DISPLAY 2 PC [DVI] [DVI IN] [DVI/VGA OUT] [DVI IN] Connect the [DP OUT] connector of DISPLAY 1 to the [DP IN] connector of DISPLAY 2.
PAGE 26
55BDL1005X 3.4.3. Analog video connection Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [VGA IN] connector of DISPLAY 2. DISPLAY 1 DISPLAY 2 PC [VGA] [VGA IN] [DVI/VGA OUT] [VGA IN] 3.4.4. IR daisy-chain Connection Connect [IR Sensor Cable] to DISPLAY 1,and connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2. [IR IN] DISPLAY 1 DISPLAY 2 IR Sensor Cable [RS-232C OUT] 3.5.
PAGE 27
55BDL1005X 3.6. IR Pass-through Connection [IR OUT] DVD / VCR / VCD [IR IN] (DVD / VCR / VCD) Remote Control 3.7. Wire-connecting to Network If you connect this display to a home network, you can play photos, music and videos from your computer. See Play multimedia files via Local Area Network (Page 18) for more detail. INTERNET ROUTER [RJ-45] [RJ-45] PC To setup the network: 1. Switch on the router and switch on its DHCP setting. 2. Connect the router to this display with an Ethernet cable. 3.
PAGE 28
55BDL1005X 4. Operation • Multiple display setup: NOTE: T he control button described in this section is mainly on the remote control unless specified otherwise. 4.1. DISPLAY 1 ROUTER [RJ-45] Watch the Connected Video Source [RJ-45] DISPLAY 2 [RJ-45] PC See page 11 for external equipments connection. 1. Press [ ] SOURCE button. 2. Press [ ] or [ ] button to choose a device, then press [ button. 4.2.
PAGE 29
55BDL1005X 4. You can connect up to 4 displays to the same PC and play same media stream. 6. Check the media formats. Then, click Choose media streaming options..... 4.3.3. How to use DLNA-DMR from PC 7. Go to Advanced sharing settings, and check Turn on network discovery. 1. Press [ button. ] HOME button, choose Network and press [ ] Picture Network settings 8. Now, go to the directory of your media files. Choose the media file by right click.
PAGE 30
55BDL1005X 6. Follow the on-screen instruction to control the play option. • 7. Press [PLAY] buttons (H F G I J) to control playing. 4.5. {Status}: To view information about a video (for example, played position, duration, title, or date). 4.5.3. Playing photo files Play options 1. Choose Photo in the top bar. 4.5.1. Playing music files 1. Choose Photo Music in the top bar. 2. Choose a photo thumbnail, then press 2. Choose one music track, and press [ ] button.
PAGE 31
55BDL1005X Internet Web Address：X http:// History www.google.com w ww.google.com Bookmark . , @ ‘ a b c d e f g i j k l m n o p q r s t v w x y z h u < abc Done Hide ? ! - ABC 123 www 3. Move the cursor to “” icon and press [ Backspace ] button. Internet Web Address：X http://www.google.com History www.google.com w ww.google.com Bookmark 4. Now, you can see the web page. NOTES: • The Opera browser does not support FLASH format.
PAGE 32
55BDL1005X 5. Change your settings 5.1.1. Picture Using the remote control: SOURCE FORMAT LIST Picture Picture style Sound Backlight Tiling Colour Network Sharpness General settings Noise reduction Advanced MPEG artifact reducti... um ne Help INFO Picture enhancement Advanced Scan mode Format and edges HDMI input range ADJUST 1. Press [ OPTIONS Picture reset Picture style ] button on the remote control to display the OSD menu. Choose a predefined picture setting. 2.
PAGE 33
55BDL1005X • {V Zoom}: Expands the vertical size of the image only. Note: Zoom, H Zoom and V Zoom are functional only when the Picture format setting is set to Custom Zoom. See page 18 for the descriptions about Picture format. HDMI input range HDMI video format color ranges • {Auto}: Automatically HDMI video format color ranges. • {Limit}: Chose HDMI video format Limit range. • {Full}: Chose HDMI video format Full range.
PAGE 34
55BDL1005X Example: 2 x 2 screen matrix (4 displays) H monitors = 2 displays V monitors = 2 displays {Off} V monitors H monitors 1 2 3 4 Position Example: 5 x 5 screen matrix (25 displays) H monitors = 5 displays V monitors = 5 displays Frame comp.H Adjust the horizontal frame compensation. V monitors H monitors 1 2 3 4 5 6 11 7 12 8 13 9 14 10 15 16 21 17 22 18 23 19 24 20 25 Frame comp.V Adjust the vertical frame compensation.
PAGE 35
55BDL1005X 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 (2). Enter activate key in OSD _ Cancel Note: To use this function, serial connect all machines with RS-232 cable and set their Network control port to RS-232 too. Note: To use this function for DP 1.2 connectivity, the maximum resolution only support to 1920x1080/60Hz @ 4sets. For 4Kx2K/30Hz resolution only support to 2 sets connectivity. (3). Press [ ] button and it will pop out the on-screen keyboard.
PAGE 36
55BDL1005X 5.1.5. General settings (5). Check tiling tool status on in OSD Picture Status On Picture Menu language Sound Monitor Group Tiling Tiling Monitor ID Network Network Eco mode General settings General settings Auto search Advanced Advanced Clock Help Help Scheduling Sound Sleep timer OneWire Local KB lock RC lock Menu language 5.1.4. Network Choose language used for OSD menus. Monitor group Picture Network settings Sound Digital Media Rendere...
PAGE 37
55BDL1005X • Menu item {Daylight saving} Selection item {on, off} when “daylight saving” is “on” the real time clock would have been adjusted automatically for winter and summer time when passing the critical moment in time (eg April 5, 2015, 02.00 o’clock: time will be set 1 hour later or October 25, 2015, 02.00 o’clock: time will be set 1 hour earlier).
PAGE 38
55BDL1005X 6. If {Source}  {USB} is chosen. Go to Playlist setting. RC lock Choose to enable or disable the button function of the remote control. 0001/0002 Photo • {Unlock}: Enable the keyboard function. Photo • {Lock all}: Lock all keyboard function. Video • {Lock but volume}: Disable all the keyboard function except the [ ] and [ ] button. • {Lock but power}: Disable all the keyboard function except the [ ] POWER button.
PAGE 39
55BDL1005X 5.1.7. Help DisplayPort Ver. Set the DisplayPort version to 1.1a or 1.2, this setting is only valid on DisplayPort input and output, Picture 1.1a: Switch DisplayPort Ver. to 1.1a(default), the DisplayPort output is the clone of the DisplayPort input. Sound 1.2: Switch DisplayPort Ver. to 1.2 to support MST(Multi-Stream Transport) Network NOTE: Advanced • If the display is black screen or abnormal under DisplayPort source, please switch to 1.1a and turn AC off and on.
PAGE 40
55BDL1005X 6. USB device compatibility USB Video Subtitle Formats (for language subtitles, etc.) File Extensions Container .mpg mpeg PS .vob .ts TS Video codec Maximum resolution MPEG-1 MPEG-2 MPEG-4 ASP H.264 MPEG-2 MPEG-4 ASP H.264 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 Max.Frame Rate (fps) 25p,30p,50i,60i 25p,30p,50i,60i 25p,30p,50i,60i 25p,30p,50p,60p,60i 25p,30p,50i,60i 25p,30p,50i,60i 25p,30p,50p,60p,60i Max.
PAGE 41
55BDL1005X USB Multimedia Formats Frequency Max.Bit Rate - (kHz) 48 (Mbps) 384 MPEG-1,2,2.5 L3 - - 48 192 WMA - - 96 192 768 768 WMA,WMA Pro LPCM LPCM - - 192 768 LPCM AAC - - 48 1024 AAC,HE-AAC(v1&v2) Playlists - - - - - M4A - - 48 1024 AAC,HE-AAC(v1&v2) File Extensions Container Video codec Maximum resolution .mp3 .wma MP3 WMA - .asf .wma .wav(PC) .aif(mac) (V2 up to V9.2) WMA Pro LPCM .aiff(mac) .aac .mp4 .m4a .pls NOTES: .m3u .
PAGE 42
55BDL1005X 7. Input Mode VGA Resolution: Standard Resolution VGA Active Resolution H Pixels 640 V Lines 480 WVGA 720 400 SVGA 800 600 XGA 1024 768 WXGA 1280 WXGA Refresh Rate Pixel Rate 60 Hz 25.175 MHz 72 Hz 31.5 MHz 75 Hz 31.5 MHz 70 Hz 33.75 MHz Aspect Ratio Stand for Mode 4:3 Video Graphic Array 16:9 Wide Video Graphic Array 4:3 Super VGA 4:3 Extended Graphic Array 60 Hz 40 MHz 75 Hz 49.5 MHz 60 Hz 65 MHz 75 Hz 78.75 MHz 768 60 Hz 79.
PAGE 43
55BDL1005X 8. Pixel Defect Policy We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable.
PAGE 44
55BDL1005X 8.4. Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects: One dark dot 8.5. Two adjacent dark dots = 1 pair of dark dots Two dark dots, specifications defines the minimum distance between dark dots Proximity of Pixel Defects Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects.
PAGE 45
55BDL1005X 9. Cleaning and Troubleshooting 9.1. Cleaning Caution When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close.
PAGE 46
55BDL1005X 9.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back of the display is not switched on. 2. Make sure the power switch is switched on. 3. The selected input has no connection. 3. Connect a signal connection to the display. 4. The display is in standby mode.
PAGE 47
55BDL1005X How to setup the settings in the menu to control all the monitors at the same time and individually via RC? Daisy chained by RS232 and no IR cable 1. The first display sets as “Primary” on OSD (Advanced option/IR control item), others set as “Secondary”. 2. The setup OSD will show on Top-Left of display.(Toggle MENU will show again if it disappear) 3. Default setting: ID NO: 0, GP NO: 0, this setting can control all displays by IR.
PAGE 48
55BDL1005X 10. Technical Specifications Display: Item Screen Size (Active Area) Aspect Ratio Number of pixels Pixel pitch Displayable colors Brightness (typical) Contrast ratio (typical) Viewing angle Specifications 54,6” (138.7 cm) LCD 16:9 1920 (H) x 1080 (V) 0.630 (H) x 0.630 (V) [mm] 1.
PAGE 49
55BDL1005X General: Item Power Supply Power Consumption (Max) Specifications AC 100 - 240V, 50 - 60Hz, 6A 320 W Power Consumption (typ.) Power Consumption (Standby & Off) Dimensions (Without Stand) [W x H x D] Weight (Without Stand) 133 W <0.8 W (RS232 in active) 1211.4 x 682.2 x 98.5 (@Wall Mount) / 106.9 (@Handle) (Without side seal) 24.35 Kg Gross Weight (Without Stand) 36.
PAGE 50
2017 © Koninklijke Philips N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. Specifications are subject to change without notice.