User manual

ManualsBrandsPhilips ManualsSignage SolutionsSignage Solutions Video Wall Display

www.philips.com/welcome

BDL5588XC

55BDL3005X

V1.30

User Manual (English)

Summary of content (51 pages)

PAGE 1
BDL5588XC 55BDL3005X V1.30 www.philips.
PAGE 2
BDL5588XC/55BDL3005X Safety Instructions Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your display: Operation: • Keep the display out of direct sunlight and away from stoves or any other heat sources.
PAGE 3
BDL5588XC/55BDL3005X Read and follow these instructions when connecting and using your display: • Unplug the display if you are not going to use it for an extensive period of time. • Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids.
PAGE 4
BDL5588XC/55BDL3005X Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
PAGE 5
BDL5588XC/55BDL3005X Information for U.K. only WARNING - THIS APPLIANCE MUST BE EARTHED. (B) Important: (A) This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows:+ 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
PAGE 6
BDL5588XC/55BDL3005X 中国大陆RoHS 根据中国大陆《电子电气产品有害物质限制使用标识要求》，以下部分列出了本产品中可能包含的有害物质的名称和含量。有害物质部件名称铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr (VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 外壳 ○ ○ ○ ○ ○ ○ 液晶显示屏 × ○ ○ ○ ○ ○ 电路板组件* × ○ ○ ○ ○ ○ 电源适配器 × ○ ○ ○ ○ ○ 电源线/连接线 × ○ ○ ○ ○ ○ 遥控器 X ○ ○ ○ ○ ○ 本表格依据SJ/T 11364 的规定编制。 *: 电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路、连接器等。 O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572规定的限量要求以下。 X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。上表中打“×”的部件，应功能需要，部分有害物质含量超出GB/T 26572规定的
PAGE 7
BDL5588XC/55BDL3005X 《废弃电器电子产品回收处理管理条例》提示性说明为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品回收处理相关法律法规，将其交给当地具有国家认可的回收处理资质的厂商进行回收处理，不当利用或者处置可能会对环境和人类健康造成影响。娤⌈ 㨢᳸$䵥ᵥ⍿Ʋ◦䏝㯹䉭❁ᳫ濕媣ᵥ⍿⊭侻ᷘ廞ノ㒞䵽䏳ⴰㄮƲ◦店䢋⾃⁳᳉濕⊭侻斾堿䏦ヵ ⪷ⴰㄮ悅⊔⃅⩜⊭圊䕂㉨㑻Ʋ 限用物質及其化學符號單元鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 (Cr+6) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 塑料外框 ○ ○ ○ ○ ○ ○ 後殼 ○ ○ ○ ○ ○ ○ 液晶面板－ ○ ○ ○ ○ ○ 電路板組件－ ○ ○ ○ ○ ○ 底座 ○ ○ ○ ○ ○ ○ 電源線－ ○ ○ ○ ○ ○ 其他線材－ ○ ○ ○ ○ ○ 遙控器－ ○ ○ ○ ○ ○ 喇叭（選配）－ ○ ○ ○ ○
PAGE 8
BDL5588XC/55BDL3005X End-of-Life Disposal Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of. Please find out about the local regulations on how to dispose of your old display from your local Philips dealer. (For customers in Canada and U.S.A.) This product may contain lead and/or mercury.
PAGE 9
BDL5588XC/55BDL3005X Após o uso, as pilhas e/ou baterias deverão ser entregues ao estabelecimento comercial ou rede de assistência técnica autorizada. Information for EAC Month and year of manufacturing please refer information in Rating label. Name and location of manufacturer ООО “Профтехника” Адрес: 3-й Проезд Марьиной рощи, 40/1 офис 1. Москва, 127018, Россия Importer and information Наименование организации: ООО “Профтехника” Адрес: 3-й Проезд Марьиной рощи, 40/1 офис 1.
PAGE 10
BDL5588XC/55BDL3005X Table Of Contents 1. 2. 3. Unpacking and Installation........................................................1 1.1. Unpacking..........................................................................................1 1.2. Package Contents.........................................................................1 1.3. Installation Notes..........................................................................1 1.4. Installing and Removing Table Stands (optional).........2 1.5.
PAGE 11
BDL5588XC/55BDL3005X 1. Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • Due to the size and weight of this display it is recommended for two people to move it. • After opening the carton, ensure that the contents are complete and in good condition. 1.2.
PAGE 12
BDL5588XC/55BDL3005X 1.4. Installing and Removing Table Stands (optional) To install table stands: 1. Ensure your display is powered off. 2. Spread a protective sheet on a flat surface. 3. Grab the carrying handles and place the display face-down on the protective sheet. 4. After inserting the stand in the guide block, tighten the screws on both sides of the display. NOTE: The longer side of the stand should face the front of the display.
PAGE 13
BDL5588XC/55BDL3005X 1.5. Mounting on a Wall To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface that complies with TUV-GS and/or UL1678 standard in North America. Protective Sheet VESA Grid Table Tabletop stand 1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the screen face. 2.
PAGE 14
BDL5588XC/55BDL3005X 1.6. Mounting in Portrait Position This display can be installed in portrait position. 1. Remove the table stand, if attached. 2. Rotate 90 degrees anticlockwise. The “ ” logo should be bristling when facing the display at the back.
PAGE 15
BDL5588XC/55BDL3005X 1.7. Operating Instructions of Edge Alignment Kit 1.7.1. Installing Edge Alignment Kit • Before install edge alignment kit, displays must be mounted to video wall frame correctly. • Using “Thumb Screw” for easy installing. • Using “Edge Alignment Kit-1” on adjacent four displays. 2 3 1 4 5 8 7 • Using “Edge Alignment Kit-2” on adjacent two displays. • Install the “Edge Alignment Kit-2” with 2 PCS of M4 screw.
PAGE 16
BDL5588XC/55BDL3005X 1.8. Using of Edge Finishing Kit (Optional) You could use the edge finishing kit to protect the display and have a better appearance. 1.8.1.
PAGE 17
BDL5588XC/55BDL3005X 2. Parts and Functions 2.1. Control Panel 9 MUTE INPUT 1 1 2 3 MENU 4 5 [ ] button 9 Use this button to turn the display on or put the display to standby. 2 [MUTE] button 4 [ ] button [ ] button [ ] button [ ] button Move the highlight bar down to adjust the selected item while OSD menu is on.
PAGE 18
BDL5588XC/55BDL3005X 2.2. Input/Output Terminals 22 21 20 19 24 2 6 1 1 3 4 5 16 18 13 7 9 10 11 12 14 15 17 8 AC IN 15 MAIN POWER SWITCH 16 IR IN / 17 AC power input from the wall outlet. 2 Component YPbPr video source input. Switch the main power on/off. 3 4 IR OUT 18 6 19 20 RS232C OUT 21 RJ-45 HDMI1 IN / 9 22 23 DVI IN NOTES: We recommend to use Advantech ARK DS262 or Winmate OMIS-OPS modules. We’ll not guarantee other OPS modules.
PAGE 19
BDL5588XC/55BDL3005X 2.3. Remote Control 1 [ ] POWER button Turn the display on or put the display to standby. 2.3.1. General functions 2 [PLAY] buttons Control playback of media files. 3 1 [ ] SOURCE button Choose input source. Press [ ] or [ ] button to choose from USB, Network, Internet, SmartCMS, HDMI 1, HDMI 2, DisplayPort, Card OPS, DVI-D, YPbPr, AV, or VGA. Press [ ] button to confirm and exit. 2 4 [ ] HOME button Access the OSD menu.
PAGE 20
BDL5588XC/55BDL3005X 2.3.2. ID Remote Control Press [ID] button. The red LED blinks twice. 1. Press [ID SET] button for more than 1 second to enter the ID Mode. The red LED lights up. Press the [ID SET] button again will exit the ID Mode. The red LED lights off. You can set the remote control ID when you want to use this remote control on one of several different displays. Press the digit numbers [0] ~ [9] to select the display you want to control. For example: press [0] and [1] for display No.
PAGE 21
BDL5588XC/55BDL3005X 2.3.3. Inserting the batteries in the remote control The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: 1. Press and then slide the cover to open it. 2. Align the batteries according to the (+) and (–) indications inside the battery compartment. 3. Replace the cover. Caution: The incorrect use of batteries can result in leaks or bursting.
PAGE 22
BDL5588XC/55BDL3005X 3. Connecting External Equipment 3.1. Connecting External Equipment (DVD/VCR/VCD) 3.1.1. Using COMPONENT video input Audio Out COMPONENT Out (YPbPr) DVD / VCR / VCD [AUDIO IN] [COMPONENT IN] (YPbPr) 3.1.2.
PAGE 23
BDL5588XC/55BDL3005X 3.1.3. Using HDMI video input DVD / VCR / VCD HDMI Out [HDMI IN] 3.2. Connecting a PC 3.2.1. Using VGA input VGA Out D-Sub 15 pin Audio Out PC [VGA IN] [VGA AUDIO IN] 3.2.2.
PAGE 24
BDL5588XC/55BDL3005X 3.2.3. Using HDMI input HDMI Out PC [HDMI IN] 3.2.4. Using DisplayPort input DisplayPort Out PC [DisplayPort IN] 3.3. Connecting Audio Equipment 3.3.1.
PAGE 25
BDL5588XC/55BDL3005X 3.3.2.
PAGE 26
BDL5588XC/55BDL3005X 3.4. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall. 3.4.1. Display control connection Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2. DISPLAY 1 DISPLAY 2 PC [RS-232C] [RS-232C IN] [RS-232C OUT] [RS-232C IN] DISPLAY 1 DISPLAY 2 [RJ-45] PC [RJ-45] [RS-232C OUT] [RS-232C IN] 3.4.2.
PAGE 27
BDL5588XC/55BDL3005X Connect the [DVI OUT ] connector of DISPLAY 1 to the [DVI IN] connector of DISPLAY 2. DVD / VCR / VCD DISPLAY 1 DISPLAY 2 [HDMI] [DVI IN] [DVI OUT] [DVI IN] 3.4.3. Analog video connection Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [VGA IN] connector of DISPLAY 2. DISPLAY 1 DISPLAY 2 PC [VGA] [VGA IN] [DVI/VGA OUT] [VGA IN] 3.4.4.
PAGE 28
BDL5588XC/55BDL3005X NOTE: This display’s remote control sensor will stop working if the [IR IN] is connected. 3.6. IR Pass-through Connection [IR OUT] DVD / VCR / VCD [IR IN] (DVD / VCR / VCD) Remote Control 3.7. Wire-connecting to Network If you connect this display to a home network, you can play photos, music and videos from your computer. See Play multimedia files via Local Area Network (Page 19) for more detail. INTERNET ROUTER [RJ-45] [RJ-45] PC To setup the network: 1.
PAGE 29
BDL5588XC/55BDL3005X 4. Operation • Multiple display setup: NOTE: The control button described in this section is mainly on the remote control unless specified otherwise. 4.1. DISPLAY 1 Watch the Connected Video Source ROUTER [RJ-45] [RJ-45] DISPLAY 2 [RJ-45] PC See page 12 for external equipments connection. 1. Press [ ] SOURCE button. 2. Press [ ] or [ ] button to choose a device, then press [ button. 4.2.
PAGE 30
BDL5588XC/55BDL3005X 4. You can connect up to 4 displays to the same PC and play same media stream. 6. Check the media formats. Then, click Choose media streaming options..... 4.3.3. How to use DLNA-DMR from PC 7. Go to Advanced sharing settings, and check Turn on network discovery. 1. Press [ button. ] HOME button, choose Network and press [ ] Picture Network settings 8. Now, go to the directory of your media files. Choose the media file by right click.
PAGE 31
BDL5588XC/55BDL3005X 6. Follow the on-screen instruction to control the play option. 7. Press [PLAY] buttons ( 4.5. • ) to control playing. {Status}: To view information about a video (for example, played position, duration, title, or date). 4.5.3. Playing photo files Play options 1. Choose Photo in the top bar. 4.5.1. Playing music files 1. Choose Photo Music in the top bar. 2. Choose a photo thumbnail, then press If there are multiple photos in a folder, choose a photo.
PAGE 32
BDL5588XC/55BDL3005X Internet Web Address：X http:// History www.google.com w ww.google.com Bookmark . , @ ‘ a b c d e f g i j k l m n o p q r s t v w x y z h u < abc Done Hide ? ! - ABC 123 www 3. Move the cursor to “” icon and press [ Backspace ] button. Internet Web Address：X http://www.google.com History www.google.com w ww.google.com Bookmark 4. Now, you can see the web page. NOTES: • The Opera browser does not support FLASH format.
PAGE 33
BDL5588XC/55BDL3005X 5. Change your settings 5.1.1. Picture Using the remote control: SOURCE FORMAT LIST Picture Picture style Sound Backlight Tiling Colour Network Sharpness General settings Noise reduction Advanced MPEG artifact reducti... um ne Help INFO Picture enhancement Advanced Scan mode Format and edges HDMI input range ADJUST 1. Press [ OPTIONS Picture reset Picture style ] button on the remote control to display the OSD menu. Choose a predefined picture setting. 2.
PAGE 34
BDL5588XC/55BDL3005X • {V Zoom}: Expands the vertical size of the image only. Note: Zoom, H Zoom and V Zoom are functional only when the Picture format setting is set to Custom Zoom. See page 19 for the descriptions about Picture format. HDMI input range HDMI video format color ranges • {Auto}: Automatically HDMI video format color ranges. • {Limit}: Chose HDMI video format Limit range. • {Full}: Chose HDMI video format Full range.
PAGE 35
BDL5588XC/55BDL3005X Example: 2 x 2 screen matrix (4 displays) H monitors = 2 displays V monitors = 2 displays {Off} V monitors H monitors 1 2 3 4 Position Example: 5 x 5 screen matrix (25 displays) H monitors = 5 displays V monitors = 5 displays Frame comp.H Adjust the horizontal frame compensation. V monitors H monitors 1 6 11 16 21 2 7 12 17 22 3 8 13 18 23 4 9 14 19 24 5 10 15 20 25 Frame comp.V Adjust the vertical frame compensation.
PAGE 36
BDL5588XC/55BDL3005X 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 (2). Enter activate key in OSD _ Cancel Note: To use this function, serial connect all machines with RS-232 cable and set their Network control port to RS-232 too. Note: To use this function for DP 1.2 connectivity, the maximum resolution only support to 1920x1080/60Hz @ 4sets. For 4Kx2K/30Hz resolution only support to 2 sets connectivity. (3). Press [ ] button and it will pop out the on-screen keyboard.
PAGE 37
BDL5588XC/55BDL3005X 5.1.5. General settings (5). Check tiling tool status on in OSD Picture Menu language Sound Sound Monitor Group Tiling Tiling Monitor ID Network Network Eco mode General settings General settings Auto search Advanced Advanced Clock Help Help Scheduling Picture Status On Sleep timer OneWire Local KB lock RC lock Menu language 5.1.4. Network Choose language used for OSD menus. Picture Network settings Sound Digital Media Rendere...
PAGE 38
BDL5588XC/55BDL3005X when “daylight saving” is “on” the real time clock would have been adjusted automatically for winter and summer time when passing the critical moment in time (eg April 5, 2015, 02.00 o’clock: time will be set 1 hour later or October 25, 2015, 02.00 o’clock: time will be set 1 hour earlier). Scheduling This function allows you to program up to 7 different scheduled time intervals for this display to activate.
PAGE 39
BDL5588XC/55BDL3005X 6. If {Source}  {USB} is chosen. Go to Playlist setting. RC lock Choose to enable or disable the button function of the remote control. 0001/0002 Photo • {Unlock}: Enable the keyboard function. Photo • {Lock all}: Lock all keyboard function. Video • {Lock but volume}: Disable all the keyboard function except the [ ] and [ ] button. • {Lock but power}: Disable all the keyboard function except the [ ] POWER button.
PAGE 40
BDL5588XC/55BDL3005X 5.1.7. Help DisplayPort Ver. Set the DisplayPort version to 1.1a or 1.2, this setting is only valid on DisplayPort input and output, Picture 1.1a: Switch DisplayPort Ver. to 1.1a(default), the DisplayPort output is the clone of the DisplayPort input. Sound 1.2: Switch DisplayPort Ver. to 1.2 to support MST(Multi-Stream Transport) Network NOTE: Advanced • If the display is black screen or abnormal under DisplayPort source, please switch to 1.1a and turn AC off and on.
PAGE 41
BDL5588XC/55BDL3005X 6. USB device compatibility USB Video Subtitle Formats (for language subtitles, etc.) File Extensions Container .mpg mpeg PS .vob .ts TS Video codec Maximum resolution MPEG-1 MPEG-2 MPEG-4 ASP H.264 MPEG-2 MPEG-4 ASP H.264 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 MVC 1920x1080p@frame rate=24, 25,30Hz Max.
PAGE 42
BDL5588XC/55BDL3005X USB Multimedia Formats Frequency Max.Bit Rate - (kHz) 48 (Mbps) 384 MPEG-1,2,2.5 L3 - - 48 192 WMA - - 96 192 768 768 WMA,WMA Pro LPCM LPCM - - 192 768 LPCM AAC - - 48 1024 AAC,HE-AAC(v1&v2) Playlists - - - - - M4A - - 48 1024 AAC,HE-AAC(v1&v2) File Extensions Container Video codec Maximum resolution .mp3 .wma MP3 WMA - .asf .wma .wav(PC) .aif(mac) (V2 up to V9.2) WMA Pro LPCM .aiff(mac) .aac .mp4 .m4a .pls NOTES: .m3u .
PAGE 43
BDL5588XC/55BDL3005X 7. Input Mode VGA Resolution: Standard Resolution VGA Active Resolution H Pixels 640 V Lines 480 WVGA 720 400 SVGA 800 600 XGA 1024 768 WXGA 1280 WXGA Refresh Rate Pixel Rate 60 Hz 25.175 MHz 72 Hz 31.5 MHz 75 Hz 31.5 MHz 70 Hz 33.75 MHz Aspect Ratio Stand for Mode 4:3 Video Graphic Array 16:9 Wide Video Graphic Array 4:3 Super VGA 4:3 Extended Graphic Array 60 Hz 40 MHz 75 Hz 49.5 MHz 60 Hz 65 MHz 75 Hz 78.75 MHz 768 60 Hz 79.
PAGE 44
BDL5588XC/55BDL3005X 8. Pixel Defect Policy We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable.
PAGE 45
BDL5588XC/55BDL3005X 8.4. Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects: One dark dot 8.5.
PAGE 46
BDL5588XC/55BDL3005X 9. Cleaning and Troubleshooting 9.1. Cleaning Caution When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close.
PAGE 47
BDL5588XC/55BDL3005X 9.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back of the display is not switched on. 2. Make sure the power switch is switched on. 3. The selected input has no connection. 3. Connect a signal connection to the display. 4. The display is in standby mode.
PAGE 48
BDL5588XC/55BDL3005X How is the RC working? Daisy chain : no RS232 connected and IR cable No need setting, just to connect with IR cables and control by IR. *This way has out-of-synchronizm phenomenon. Suggest to use above setting with RS-232 cable.
PAGE 49
BDL5588XC/55BDL3005X 10. Technical Specifications Display: Item Screen Size (Active Area) Aspect Ratio Number of pixels Pixel pitch Displayable colors Brightness (typical) Contrast ratio (typical) Viewing angle Specifications 54,6” (138.7 cm) LCD 16:9 1920 (H) x 1080 (V) 0.630 (H) x 0.630 (V) [mm] 1.
PAGE 50
BDL5588XC/55BDL3005X General: Item Power Supply Power Consumption (Max) Specifications AC 100 - 240V, 50 - 60Hz, 3.5A 320 W Power Consumption (typ.) Power Consumption (Standby & Off) Dimensions (With Stand) [W x H x D] Dimensions (Without Stand) [W x H x D] Weight (With Stand) Weight (Without Stand) 185 W <0.5 W 1213.4 x 726.2 x 400.0 1213.4 x 684.2 x 99.25 (@Wall mount) / 107.65 (@Handle) 28.8 Kg 26.
PAGE 51
2017 © Koninklijke Philips N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. Specifications are subject to change without notice.