55BDL3202H V1.00 www.philips.
55BDL3202H Safety Instructions Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your display: Operation: • Keep the display out of direct sunlight and away from stoves or any other heat sources. • It is recommended to set the display up in the well-ventilated place.
55BDL3202H • Only the lifetime of the display stated in this specification is guaranteed if the display is used under the proper operation conditions. IMPORTANT: Always activate a moving screen saver program when you leave your display unattended. Always activate a periodic screen refresh application if the unit will display unchanging static content.
55BDL3202H Federal Communications Commission (FCC) Notice (U.S. Only) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
5BDL3202H Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
55BDL3202H Information for U.K. only WARNING - THIS APPLIANCE MUST BE EARTHED. (B) Important: (A) This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows:+ 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
55BDL3202H China RoHS 根据中国大陆《电器电子产品有害物质限制使用管理办法》,以下部分列出了本产品中可能包含的有害 物质的名称和含量。 有害物质 部件名称 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr (VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 外壳 ○ ○ ○ ○ ○ ○ 液晶显示屏 × ○ ○ ○ ○ ○ 电路板组件* × ○ ○ ○ ○ ○ 电源适配器 × ○ ○ ○ ○ ○ 电源线/连接线 × ○ ○ ○ ○ ○ 遥控器 X ○ ○ ○ ○ ○ 本表格依据SJ/T 11364 的规定编制。 *: 电路板组件包括印刷电路板及其构成的零部件,如电阻、电容、集成电路、连接器等。 O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572规定的限量要求以下。 X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。 上表中打“×”的部件,应功能需要,部分有害物质含量超出GB/T 26572规定的限量要求,但符合
55BDL3202H 限用物質及其化學符號 單元 鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 (Cr+6) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 塑料外框 ○ ○ ○ ○ ○ ○ 後殼 ○ ○ ○ ○ ○ ○ 液晶面板 - ○ ○ ○ ○ ○ 電路板組件 - ○ ○ ○ ○ ○ 底座 ○ ○ ○ ○ ○ ○ 電源線 - ○ ○ ○ ○ ○ 其他線材 - ○ ○ ○ ○ ○ 遙控器 - ○ ○ ○ ○ ○ 喇叭(選配) - ○ ○ ○ ○ ○ 風扇(選配) - ○ ○ ○ ○ ○ 備考1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。 備考2.
55BDL3202H Waste Electrical and Electronic Equipment-WEEE Attention users in European Union private households This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection.
55BDL3202H Batteries For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation. Please contact your local authority for details on the collection and recycling schemes. For Switzerland: The used battery is to be returned to the selling point.
55BDL3202H Table Of Contents 1. 2. 3. 4. 4.3. Unpacking and Installation......................................... 1 1.1. Unpacking............................................................ 1 1.2. Package Contents.............................................. 1 1.3. Installation Notes............................................... 1 1.4. Mounting on a Wall.......................................... 2 1.4.1. VESA Grid.............................................. 2 1.5.
55BDL3202H 1. Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • As this product is high and heavy, the operation of moving the device is recommended to be performed by two technicians. • After opening the carton, ensure that the contents are complete and in good condition. 1.2.
55BDL3202H 1.4. Mounting on a Wall To mount this display on a wall, a standard wall-mounting kit (commercially available) is required. It is recommended that you use a mounting interface that complies with TUV-GS and /or UL1678 standard in North America. Protective Sheet VESA Grid Table 1. Spread a protective sheet which was wrapped around the display when it was packed on a flat surface. Lay the display facedown on the protective sheet to facilitate your operation without scratching the screen. 2.
55BDL3202H 1.5. Mounting in Portrait Orientation This display can be installed in portrait orientation. Rotate the display 90 degrees clockwise. The “ ” logo should be on the LEFT side when facing the display. 90° 90° 1.5.1. How to remove the logo 1. Prepare a piece of paper with a cutting area of logo as a protector to prevent the front bezel from scratching. 1 2 3 2. Using a knife, carefully remove the logo sticker with the paper placing beneath. 3. Tear off the logo sticker.
55BDL3202H 1.6. Operating Instructions of Edge Alignment Kit 1.6.1. Installing the Edge Alignment Kit • Before installing the edge alignment kit, the display must be mounted to the frame of video wall correctly. • We recommend you contact a professional technician when installing the edge alignment kit. We are not responsible for any damage to the product if the installation is not performed by a professional technician.
55BDL3202H 2. Parts and Functions 2.1. Control Panel 9 1 1 2 3 4 5 [ ] button 8 Press this button to turn the display On or turn the display to standby mode. 2 [MUTE] button 9 [INPUT] button Choose the input source. Confirm a selection in the OSD menu. 4 5 Remote control sensor and power status indicator • Receives command signals from the remote control.
55BDL3202H Input/Output Terminals EXT. SPK TERMINAL 2.2. USB 22 AUDIO OUT 20 19 AUDIO IN IR-IN IR-OUT RS232C IN RS232C OUT RJ45 2 4 1 1 3 RJ45 HDMI1 IN DVI IN HDMI2 IN DVI OUT 5 7 8 9 10 AC IN 11 12 4 14 IR OUT 15 16 6 17 8 18 RS232 OUT 19 LAN control function for the use of remote control signal from control center.
55BDL3202H 2.3. Remote Control 1 [ ] POWER button Turn the display on or put the display to standby. 2.3.1. General functions 2 [PLAY] buttons Control playback of media files. 3 10 1 NORMAL ID 11 2 4 12 4 5 INFO 5 6 14 7 OPTIONS 8 16 VOL ] LIST button [ ] [ ] [ ] [ ] NAVIGATION buttons [ ] ADJUST button [ ] MUTE button Press to turn the mute function on/off. 9 8 [ Access currently available options, picture and sound menus.
55BDL3202H 2.3.2. ID Remote Control Press [ID] button. The red LED blinks twice. Set the remote control ID if you intend to use this remote control on several different displays. 1. Press [ID SET] button for more than 1 second to enter the ID Mode. The red LED lights up. Press the [ID SET] button again will exit the ID Mode. The red LED lights off. Press the digit numbers [0] ~ [9] to select the display you want to control. For example: press [0] and [1] for display No.
55BDL3202H 2.3.3. Inserting the batteries in the remote control The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: 1. Press and then slide the cover to open it. 2. Insert batteries with the correct polarity (+) and (-). 3. Replace the cover. Caution: Incorrect use of batteries may cause leakage or explosion. Be sure to follow the instructions below: • Insert “AAA” batteries with the correct polarity (+ and -). • Do not mix battery types.
55BDL3202H 3. Connecting External Equipment 3.1. Connecting External Equipment (DVD/VCR/VCD) AUDIO IN AUDIO OUT 3.1.1. Using COMPONENT video input [AUDIO IN] Pr Pb Y/CVBS PC LINE IN SPEAKER SWITCH [COMPONENT IN] (YPbPr) COMPONENT Out (YPbPr) Audio Out DVD / VCR / VCD AUDIO IN AUDIO OUT 3.1.2.
55BDL3202H 3.1.3. Using HDMI video input HDMI2 IN HDMI1 IN DVI IN DVI OUT DP IN DP OUT [HDMI IN] HDMI Out DVD / VCR / VCD 3.2. Connecting a PC 3.2.1. Using VGA input PC VGA IN Pr Pb Y/CVBS PC LINE IN SPEAKER SWITCH Audio Out VGA Out D-Sub 15 pin [VGA AUDIO IN] [VGA IN] 3.2.2.
55BDL3202H 3.2.3. Using HDMI input HDMI1 IN HDMI2 IN DVI IN DVI OUT DP IN DP OUT VGA IN Pr Pb [HDMI IN] HDMI Out PC 3.2.4. Using DisplayPort input PC DP IN DP OUT VGA IN Pr Pb Y/CVBS PC LINE IN SPEAKER SWITCH DisplayPort Out [DisplayPort IN] 3.3. Connecting Audio Equipment VGA IN IR-IN IR-OUT SPDIF OUT AUDIO IN AUDIO OUT SPEAKER SWITCH EXT. SPK TERMINAL 3.3.1.
55BDL3202H 3.4. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a menu board. 3.4.1. Display control connection Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2. DISPLAY 1 DISPLAY 2 PC [RS-232C] [RS-232C IN] [RS-232C OUT] [RS-232C IN] 3.4.2.
55BDL3202H 3.6. IR Pass-through Connection [IR OUT] DVD / VCR / VCD [IR IN] NORMAL ID (DVD / VCR / VCD) FORMAT SOURCE LIST INFO ADJUST OPTIONS VOL ID SET ENTER Remote Control 3.7. Wire-connecting to Network INTERNET ROUTER [RJ-45] [RJ-45] PC Network Settings: 1. Switch the router on and enable its DHCP setting. 2. Connect the router to this display with an Ethernet cable. 3. Press [ ] HOME button on the remote control, then select Setup. 4.
55BDL3202H 4. Operation 2. Switch your PC and router On. • Single display setup: NOTE: The control button described in this section is mainly on the remote control unless specified otherwise. 4.1. Watch the Connected Video Source [RJ-45] See page 10 for external equipments connection. 1. Press [ [RJ-45] ] SOURCE button. 2. Press [ ] or [ ] button to choose a device, then press [ ] button. 4.2.
55BDL3202H Play files from display 3. Set the name of your display. 1. Press [ ] SOURCE button, choose Network, and press [ ] button. Network settings Digital Media Renderer - D... USB Network name Network Clear Internet memory Internet SmartCMS HDMI 1 HDMI 2 Display Port Card OPS DVI-D YPbPr AV VGA 2. As all PCs are connected to the same router now, select the correct one. xxxxxxxx Cancel 3. Press [ ] and [ ] to choose the directory and files to play. Done Clear 4.
55BDL3202H 4.4. Play multimedia files from USB device • ] or [ ] To search backward or forward, press [ button, press repeatedly to toggle between different speeds. • To stop the music, press [ 1. Connect your USB device to the USB port on the display. ] button. Music options EXT. SPK TERMINAL While you play the music, press [ ] OPTIONS button, then ] button to choose an option: press [ • {Shuffle}: Songs are played in a randomized order.
55BDL3202H 4.5.3. Playing photo files 1. Choose Internet Photo from the top menu bar. Web Address:X http:// Photo 2. Choose a photo thumbnail, then press [ History ] button. www.google.com w ww.google.com Start a slideshow Bookmark If there are multiple photos in a folder, choose a photo. Then, press [ ] to Play All. • To skip to the previous or next photo, press [ ] or [ ] ] button. button, and then press [ • To stop the slideshow, press [ ] button.
55BDL3202H 5. Change your settings 5.1. Press [ Using the remote control: SOURCE LIST Settings FORMAT ] HOME button. 5.1.1. Picture INFO Picture Picture style Sound Backlight Tiling Colour Network Sharpness General settings Noise reduction Advanced MPEG artifact reducti... um ne Help ADJUST Picture enhancement Advanced OPTIONS Scan mode Format and edges HDMI input range 1. Press [ ] button on the remote control to display the OSD menu. Picture reset 2.
55BDL3202H Advanced Format and edges • {Picture format}: Change the picture format. • {Zoom}: Expand the horizontal and vertical sizes of the image simultaneously. • {H Zoom}: Expand the horizontal size of the image only. • {V Zoom}: Expand the vertical size of the image only. Access advanced settings to enhance your audio experience. • {Auto volume leveling}: Enable the reduction of sudden volume changes.
55BDL3202H Position {Off} Adjust the position of this display in the screen matrix. Example: 2 x 2 screen matrix (4 displays) H monitors = 2 displays V monitors = 2 displays V monitors H monitors 1 2 3 4 Position Frame comp.H Adjust the horizontal frame compensation. Example: 5 x 5 screen matrix (25 displays) H monitors = 5 displays V monitors = 5 displays Frame comp.V Adjust the vertical frame compensation.
55BDL3202H Auto ID (2). Enter activate key in OSD Set up {Monitor ID} of the connected device according to {H monitors} settings. Example: H monitors sets as 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 _ Cancel Clear Done (3). Press [OK] button and an on-screen keypad appears to allow you enter the activate key. Select Done when you finish.
55BDL3202H 5.1.5. General settings (5). Check tiling tool status Picture Menu language Sound Sound Monitor Group Tiling Tiling Monitor ID Network Network Eco mode General settings General settings Auto search Advanced Advanced Clock Help Help Scheduling Picture Status On Sleep timer OneWire Local KB lock RC lock Menu language 5.1.4. Network Set OSD menu language. Picture Network settings Sound Digital Media Rendere...
55BDL3202H • Menu item {Daylight saving start date} Selection item {1st, 2nd, 3rd, 4th, last} Sunday of selection item {1-12 month} • Menu item {Daylight saving stop date} Selection item {1st, 2nd, 3rd, 4th, last} Sunday of selection item {1-12 month} • Menu item {Correction time} Selection item {0.5, 1.0, 1.5, 2.0} hour • address. NOTE: If {Source} {Autoplay} is chosen.
55BDL3202H 5. Go to Repeat modes and select the repeat mode. OneWire Connect and control your HDMI-CEC compliant devices through HDMI port to this display with the same remote control. Schedule 1 Status No repeat Schedule 2 Source Every Sunday Schedule 3 On time Every Monday Local KB lock Schedule 4 Off time Every Tuesday Schedule 5 Repeat modes Every Wednesday Enable or disable the keyboard (control buttons) function of the display.
55BDL3202H 5.1.6. Advanced Human sensor Set the display to turn on the backlight if human presence is detected and turn off the backlight after a preset period of time. Picture Jitter clean The options are: {Off, 10~60} minutes. This item is only available when you plug in CRD41. Sound EQ boost Tiling USB copying Network Power LED Light General settings Choose {Off} to turn off the power LED indicator.
55BDL3202H 6. USB device compatibility USB Video Subtitle Formats (for language subtitles, etc.) File Container Extensions .mpg mpeg PS .vob .ts TS Video codec Maximum resolution Max. Frame Rate (fps) Max. Bit Rate (Mbps) MPEG-1 1920x1080 25p,30p,50i,60i 30 MPEG-1(L1&L2), MPEG-2 1920x1080 25p,30p,50i,60i 30 MPEG-1,2,2.5 L3, MPEG-4 ASP 1920x1080 25p,30p,50i,60i 30 AAC/HEAAC(v1&v2), H.
55BDL3202H USB Multimedia Formats File Extensions Container Video codec Maximum resolution Frequency Max.Bit Rate (kHz) (Mbps) .mp3 MP3 - - 48 384 MPEG-1,2,2.5 L3 - - 48 192 WMA Audio codec .wma WMA .asf (V2 up to V9.2) .wma WMA Pro - - 96 768 WMA,WMA Pro .wav(PC) LPCM - - 192 768 LPCM LPCM - - 192 768 LPCM AAC - - 48 1024 AAC,HE-AAC(v1&v2) Playlists - - - - - M4A - - 48 1024 AAC,HE-AAC(v1&v2) .aif(mac) .aiff(mac) .aac .mp4 .m4a .pls .m3u .
55BDL3202H 7. Input Mode VGA Resolution: Standard Resolution Active Resolution H Pixels V Lines Refresh Rate Pixel Rate Aspect Ratio Stand for Mode VGA 640 480 60 Hz 72 Hz 75 Hz 25.175 MHz 31.5 MHz 31.5 MHz 4:3 Video Graphic Array WVGA 720 400 70 Hz 33.75 MHz 16:9 Wide Video Graphic Array SVGA 800 600 Super VGA 1024 768 4:3 Extended Graphic Array WXGA WXGA SXGA WXGA UXGA HD1080 1280 1280 1280 1360 1600 1920 768 800 1024 768 1200 1080 40 MHz 49.5 MHz 65 MHz 78.75 MHz 79.
55BDL3202H 8. Pixel Defect Policy We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCDdisplays are sometimes unavoidable.
55BDL3202H 8.4. Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off”. These are the examples of black dot defects: One dark dot 8.5. Two adjacent dark dots = 1 pair of dark dots Two dark dots, specifications defines the minimum distance between dark dots Proximity of Pixel Defects Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects.
55BDL3202H HOW TO AVOID MURA Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be minimized by these methods: • Lower the backlight brightness • Use a screen saver • Reduce the ambient temperature around the unit 9. Cleaning and Troubleshooting 9.1. Cleaning Caution When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display.
55BDL3202H 9.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back of the display is not switched on. 2. Make sure the power switch is switched on. 3. The selected input has no connection. 3. Connect a signal connection to the display. 4. The display is in standby mode.
55BDL3202H 10. Technical Specifications Display: Item Specifications Screen Size (Active Area) 54.6” (138.7 cm) LCD Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.63 (H) x 0.63 (V) [mm] Displayable colors 8bit,16.
55BDL3202H General: Item Specifications Power Supply AC 100 - 240V, 50 - 60Hz Power Consumption (Max) 508 W Power Consumption (Typ.) 280 W Power Consumption (Standby & Off) <0.5W Dimensions [W x H x D] 1243.2 x 714 x 137.9 mm Weight 32.2 Kg Gross Weight 39.6 Kg Energy Efficiency Class D Visible Screen Size 1209.6 x680.4 mm On Mode Power Consumption (W) 280 W Annual Energy Consumption (kWh) 410 kWh Standby Power Consumption (W) 0.50 W Off Mode Power Consumption (W) 0.
2019 © Koninklijke Philips N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. Specifications are subject to change without notice.