Televisions 5000 series 65PFL5922 55PFL5922 50PFL5922 43PFL5922 Register your product and get support at www.philips.com/welcome EN EN User manual • ES Manual del usuario ES FR Manuel d’utilisation • FR • For further assistance, call the customer support service in your country. To obtain assistance, contact Philips customer care center; In the U.S.A., Canada, Puerto Rico, or the U.S. Virgin Islands 1 866 202 5960 México D.F.
.English Contents 1 Notice ....................................................................................... 5 2 Getting started ...................................................................
.English Register online today at www.philips.com/welcome today to get the most benefits from your purchase. Registering your model with Philips makes you eligible for all of the valuable benefits listed below, so don't miss out. Register Online at www.philips.com/welcome to ensure: *Product safety notification By registering your product, you'll receive notification - directly from the manufacturer - in the rare case of a product recall or safety defect.
.English Important safety instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1 1. 12. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
.English 1 Notice Trademarks are the property of Koninklijke Philips N.V. or their respective owners. Funai Corporation reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this Owner’s manual is believed adequate for the intended use of the system. If the product or its individual modules or procedures are used for purposes other than those specified herein, confirmation of their validity and suitability must be obtained.
.English Positioning the TV • Large screen TVs are heavy. 2 people are required to carry and handle a large screen TV. • Make sure to hold the upper and bottom frames of the unit firmly as illustrated. Press to turn the unit on and go into standby mode. To completely turn off the unit, you must unplug the AC power plug from the AC power outlet. Disconnect the AC power plug to shut the unit off when trouble is found or not in use. The AC plug shall remain readily available.
.English Copyright All other registered and unregistered trademarks are the property of their respective owners. The terms HDMI and HDMI HighDefinition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries. Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
.English 2 Getting started Supplied accessories User manual Quick start guide Caution sheet CAUTION: READ THIS FIRST Features • DTV / Analog TV / CATV You can use your remote control to select channels which are broadcast in digital format and conventional analog format. Also, cable and satellite subscribers can access their TV channels. • Information display You can display on the TV screen the title, contents (DTV only) and other information on the current program.
.English Unpacking 5 Support the top of the TV set with a hand to prevent the TV from falling. 6 Unhinge the retaining tabs and unfold the left and right side of the bottom packaging. It is recommended that two or more people remove the TV set from the box. Be careful not to injure your fingers and keep children away during assembly. (65PFL5922) 1 2 Open the top flaps of the box. Remove all accessories. Caution(s) • DO NOT take the TV set out of the box yet.
.English (55PFL5922, 50PFL5922) 1 Installing the stands Open the top flaps of the box. (65PFL5922) 1 Remove both of the bottom polystyrene foam bases. Carefully tear the plastic bag until the bottom corner of the TV is exposed. • Support the top of the TV set at all times to prevent the TV from falling. 2 Remove all accessories.
.English 5 Fasten the other stand to the TV with 2 screws (included). (55PFL5922, 50PFL5922) 1 Remove the tape on the bottom of the TV set and the plastic bag. 2 Fasten the matching stand to the TV with 2 screws (included). While fastening the screws, hold the stand to prevent it from falling. 2 screws required 6 Both stands should now be securely fastened.
.English (43PFL5922) Lifting the TV set 1 Carefully lift the TV set as shown in the illustration and place it onto a stable, level surface. Protect the plate with care Removing cardboard 2 Remove the cardboard attached to the screen. You are now ready to set up and enjoy your Philips TV. ×4 Installing the remote control batteries 3 1 2 Slide the battery cover off the back of the remote control. 3 Slide the cover back into position. Insert the two supplied batteries (AAA, 1.5V).
.English Remote control a (POWER) Turns the TV on from standby or off to standby. SOURCE Selects connected devices. EasyLink buttons / r b . : Searches backward or forward through the disc. : Starts, pauses or resumes playback. . : Stops the disc playback. '/( : Skips backward or forward chapters, titles or tracks on a disc. c Note(s) q d e f p g h i o j n k m l • Pause may not work properly on some devices even if they are EasyLink (HDMI CEC) compliant.
.English Control panel Terminals g b a m h f i j c d e Remote control sensor Receives IR signal from remote control. CH + / – Selects a channel. In the menu screen, moves the cursor up (+) / down (–). (POWER) Turns the TV on or switches the TV into standby mode. MENU Opens the main on-screen menu. SOURCE Selects connected devices. VOL + / – Adjusts the volume. In the menu screen, moves the cursor left (+) / right (–).
.English Connecting Antenna or Cable / Satellite / IPTV set-top box Connecting a Cable / Satellite / IPTV set-top box, Bluray disc / DVD recorder via composite connectors and analog audio Be sure your antenna or another device is connected properly before plugging in the AC power cord. Do not place your recorder too close to the screen because some recorders can be susceptible to harmful interference from the TV.
.English No supplied cables are used with these connections: • Please purchase the necessary cables at your local store. Connecting your devices Before you connect the AC power cord: Be sure other devices are connected properly before plugging in the AC power cord. Selecting your connection quality HDMI digital connection HDMI connection offers the highest picture quality.
.English HDMI-ARC connection Composite analog video connection HDMI-ARC allows you to use EasyLink to output TV audio directly to a connected audio device, without the need for an additional digital audio cable. Composite analog video connection offers standard picture quality for video devices connected to the unit. HDMI 2 IN only HDMI cable If you connect to the unit’s component / composite video (Y/VIDEO) input jack (green), connect audio cables to the audio (L/R) input jacks.
.English Connecting the TV to the internet using a wireless LAN PC connection HDMI connection Internet This unit can be connected to your PC that has an HDMI terminal. Use an HDMI cable for this digital connection. Network provisioning equipment OUT IN LAN HDMI cable PC Ethernet cable HDMI-DVI connection WLAN Broadband router Note(s) This unit can be connected to your PC that has a DVI terminal. Use an HDMI-DVI conversion cable for this video digital connection and it requires stereo mini 3.
.English The following PC-input video signals can be displayed: Format Resolution VGA 640 x 480 SVGA 800 x 600 XGA WXGA FHD UHD 1,024 x 768 USB memory stick Refresh rate 60Hz This unit offers easy playback of picture, music and video files. Insert the USB memory stick into the USB terminal shown below. For a complete list of file formats and specifications supported, refer to USB Section p.
.English These operations are accessible by remote control. Some may also be accessible by the main unit's control panel. 5 After the standby mode setting is completed, Chromecast built-in TV setup screen will appear. TV initial setup This section will guide you through the unit’s Initial setting which includes selecting a language for your on-screen menu, country, location and Autoprogram, which automatically scans and memorizes viewable channels.
.English 9 After an TV initial setup is completed... Use to select Antenna for TV channels or Cable for CATV channels, then press OK. • If you want to scan the channels automatically again. Search for channels p. 38 • If you want to change to another language. Language p. 35 • If you want to change the location setting. Location Installation Make sure that you have attached your antenna or cable signal into the jack on the back of your TV labeled "ANTENNA IN". • Antenna Cable p.
.English Chromecast built-in TV setup 4 Network configuration • The “OK” button appears on your mobile device, complete settings Prerequisites for Chromecast built-in TV setup on this screen and then touch “OK” to proceed. Pressing it moves to the wireless network setting screen. Select your wireless network name (SSID) and enter the password to proceed. • iOS or Android™ Smartphone / Tablet with Bluetooth and location services turned on. • Have your wireless router’s SSID and password handy.
.English 3 Use your TV Switching channels TV Switching on your TV and putting it in standby mode TV Remote control Remote control To turn the TV on from standby or off to standby • Press on the TV or the remote control. To select channels by using CH + / – • Press CH + / – on the TV or the remote control. Note(s) • Energy consumption contributes to air and water pollution.
.English Watching channels from an external device Scan connections You can rescan TV connections and update the source list. Before you begin: Switching each input mode can easily switch with the remote control between TV and external devices when they are connected to the unit. 1 Turn on the set-top box or the connected device. You must set On in Master EasyLink. 1 2 3 4 p. 36 Press SOURCE on the remote control. Use to move the cursor to any device.
.English For 4:3 video signal Changing Picture format Display modes can be selected when your TV receives a 16:9 or 4:3 video signal. Three types of display modes can be selected for a PC input signal. Press FORMAT repeatedly to switch the TV aspect ratio. For 16:9 video signal (4096 x 2160p) Unscaled Super zoom 4:3 Wide screen Movie expand 16:9 Movie expand 14:9 Automatic Other than DTV and HDMI connected devices, enlarges the picture to best fit the screen.
.English TV screen information Using options menu You can display the currently selected channel or other information such as the aspect ratio on the TV screen. You can access to some TV settings directly by using OPTIONS. In the digital mode, the detailed broadcasting information for the current off-the-air channel such as program title and program guides are displayed. 1 1 Press OPTIONS to display options menu, then press OK. 2 Use Press INFO. a b c Options d 1 1.
.English Picture and sound Following settings can be configured. USB Auto picture To set predefined picture mode. Picture p. 31 Your TV is fitted with a USB connection that enables you to view photos, listen to music or watch video files stored on a USB memory stick. Auto sound To set predefined sound mode. Sound p. 33 Headphone volume To adjust headphone volume. Sound p. 33 1 2 TV speakers To Select the audio output from the unit’s speakers or not. Sound p.
.English Note(s) • This unit accepts USB memory stick only. Other storage devices such as external HDD by USB bus power will not work. • Do not use an extension cord and/or USB hub to connect devices to this unit. Always directly insert the USB flash memory stick to this unit directly. • We cannot be held responsible if your USB memory stick is not supported, nor will we accept any liability for damage or loss of stored data. Viewing photos 1 2 3 fingerprint recognition are not supported.
.English Playing music Playing movies 1 2 3 1 2 3 Use to select Music, then press OK. Use to select the desired item, then press OK. Press OK or . to play the selected files. • Press OK or . to pause, then press OK or . again to resume. to fast-forward search. • Press Press to fast-backward search. • • Press . to stop playback. • Press OPTIONS to display the optional menu, then use to Use to select Movie, then press OK. Use to select the desired item, then press OK.
.English 4 Getting more from your TV This section explains functionality of the main TV menu. 1 Press MENU to display the main TV menu. Picture and sound setup Guides you to get the best picture and sound settings. TV settings 2 Use p. 31 to select the desired menu item, then press OK. Accesses menus that allow you to change picture, sound and TV usage settings.
.English When you adjust the following settings, Personal picture will be set automatically. Picture and sound setup Before you begin: Cursor You must set Home in Location. p. 35 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into standby mode. Backlight To reduce power consumption and brightness 1 Contrast To decrease contrast 2 Press MENU and use then press OK.
.English You may adjust picture quality and enhancement settings using Pixel Plus Ultra HD and Advanced settings sub menus.
.English This selects sound modes for more spatial or surround sound reproduction. Sound Before you begin: You must set Home in Location. p. 35 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into standby mode. 1 2 Press MENU and use Use to select Sound, then press OK. Picture Sound Chromecast Built-in TV settings Features Installation Accessibility 3 to select TV settings, then press OK.
.English Chromecast Built-in TV settings Features Displays Chromecast Built-in TV settings. If you set Wake on Cast (LAN) to On, you can turn your TV on when you use your Smartphone, Tablet or PC via your home network. 1 2 1 2 Press MENU and use Use Use to select TV settings, then press OK. to select Features, then press OK. to select TV settings, then press OK.
.English Preferences Installation 1 2 Press MENU and use Use to select TV settings, then press OK. You can set the unit to reduce the power consumption or adjust the backlight brightness in Location setting. EasyLink allows you to operate your connected EasyLink device. to select Installation, then press OK.
.English TV placement EasyLink (HDMI CEC) To apply the best settings for your TV, select wall mount or stand mount. This function allows you to operate the linked functions between our brand devices with a EasyLink feature and this unit connecting through an HDMI cable. You must connect this unit to our brand EasyLink devices and be sure its EasyLink (HDMI CEC) setting is also set to on. 1 2 3 Use to select Preferences, then press OK. Use to select TV placement, then press OK.
.English Return your settings to default values Caption settings You can return settings to their default values. Closed captions displays the audio portion of the program as superimposed text over the video. 1 2 Use to select Restore default settings, then press OK. Use to select Reset AV settings or Reset all settings, then press OK. Reset AV settings Return picture and sound settings to their default values. The channel installation settings are not affected.
.English Cable / NTSC (Analog) TV operation Digital audio preferences You can set the interpretive broadcasting by an audio explanation. Caption service The primary closed captions and text services. The closed captions or text is displayed in the same CC-1 and T-1 language as the program’s dialog (up to 4 lines of script on the TV screen). Serve as the preferred data CC-3 and channels. The closed captions or T-3 text is often a secondary language.
.English Channel settings Child lock 1 Press MENU and use to select Channel settings, then press OK. You can prevent your children from watching certain programs or certain channels by locking the TV controls and by using ratings. 2 Adjust the following items. 1 Installation mode Channel installation Uninstall channels Child lock Change PIN Digital audio language Mono/Stereo Use to select Child lock, then press OK.
.English TV ratings lock US TV ratings TV ratings lock Movie ratings lock Canadian English rating Canadian French rating Region ratings lock All None TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA Sub rating TV-Y7 Fantasy Violence TV-PG Violence Sex Language Dialog TV-14 Violence Sex Language TV-MA Note(s) • • You cannot block a sub rating if the main rating is set to . • Changing the category to , or automatically changes all its sub ratings to the (, or ).
.English Change PIN Update software Although the default PIN code (0000) is supplied with the unit, you can set your own PIN code. Philips continuously tries to improve its products and we strongly recommend that you upgrade the TV software when upgrades are available. 1 2 3 Use to select Change PIN, then press OK. Press the NUMBER buttons to enter the current 4-digit PIN code. Press the NUMBER buttons to enter the new 4-digit PIN code. • Enter PIN code again to confirm.
.English USB upgrade Network updates You can upgrade the software by using USB memory stick. You can update the software by connecting the unit to the internet. 1 1 Press MENU and use to select Update software, then press OK. 2 3 Use to select Network, then press OK. Use to select Yes, then press OK. Connect your USB memory stick with the upgrade file to the USB terminal on the side of your TV. • 4 Confirmation message will appear.
.English Software settings Software 1 Press MENU and use to select Software settings, then press OK. 2 Use to select Software, then press OK. Checking your current software version number 1 Use • to select Software information, then press OK. The version and a description of the current software is displayed. Checking your current Cast software version number 1 Use to select Cast software version, then press OK. • The Cast software version is displayed.
.English 5 Useful tips FAQ Question Answer • Check the antenna or cable connection to the main unit. • Check the batteries on the remote control. • Check if there is an obstacle between the infrared sensor window and the remote control. • Test the IR signal output use IR signal check. p. 47 My remote control does not work. What should I do? If okay, then possible infrared sensor trouble. • Aim the remote control directly at the infrared sensor window on the front of the unit.
.English Troubleshooting tips If the unit does not perform properly when operated as instructed in this manual, Please check the following Troubleshooting tips and all connections once before calling for service. Power No power • Make sure the AC power cord is plugged in. • Make sure that the AC outlet supplies the proper voltage, plug another electrical appliance into the AC outlet to ensure that the AC outlet operates normally.
.English Closed captions Closed captions are displayed as a white box. No closed captions are displayed in the closed captions-supported program. • Interference from buildings or weather conditions may cause closed captions to be incomplete if watching analog TV signals. • Broadcasting station may shorten the program to insert advertisements. The closed caption decoder cannot read the information of the shortened program. Black box is displayed on the TV screen. • The text mode is selected for caption.
.English 6 Information Glossary Maintenance Analog TV (NTSC) Cleaning Acronym that stands for National Television Systems Committee and the name of analog broadcasting standards. Off the air analog TV signals are no longer being sent by major broadcasting stations in the USA. ARC (Audio Return Channel) (HDMI 2 only) HDMI-ARC allows you to use Philips EasyLink to output TV audio directly to a connected audio device, without the need for an additional digital audio cable.
.English 7 Specifications Model # Picture Type Diagonal screen size / Aspect ratio Viewing angles Built-in digital / analog tuner Sound Mono / Stereo Power output (RMS watts) Equalizer Ease of use SD (4:3 source) HD Picture format (16:9 source) UHD Photo slide show Music playback Video playback Channel Channel coverage CATV (Analog NTSC) Tuning system Channel access Connectivity Component video input (Y/Pb/Pr) Composite video input (Shared Y green terminal with component video) HDMI input Analog audio
.English 8 Warranty Limited warranty one (1) year Warranty coverage : This warranty obligation is limited to the terms as set forth below. Who is covered: This product warranty is issued to the original purchaser or the person receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer.
.English License Funai Corporation, Inc. hereby offers to deliver, upon request, a copy of the complete corresponding source code for the copyrighted open source code packages, on an “AS IS” basis, used in this product for which such offer is requested by the respective licenses. This offer is valid up to three years after the product purchase to anyone in receipt of this information. To obtain source code, please contact Funai Corporation, Inc.
Funai Corporation, Inc. 12489 Lakeland Road, Santa Fe Springs, CA 90670, USA This product has been manufactured by and is sold under the responsibility of Funai Corporation, Inc., and Funai Corporation, Inc. is the warrantor in relation to this product. The Philips trademark and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. used under license.
