Televisions 5000 series 65PFL5903 55PFL5903 50PFL5903 Register your product and get support at www.philips.com/welcome EN EN User manual • ES Manual del usuario ES FR Manuel d’utilisation • FR • For further assistance, call the customer support service in your country. To obtain assistance, contact Philips customer care center; In the U.S.A., Canada, Puerto Rico, or the U.S.
.English Contents 1 Notice .................................................................................................................. 5 2 Getting started ......................................................................................
.English Register online today at www.philips.com/support today to get the most benefits from your purchase. Registering your model with Philips makes you eligible for all of the valuable benefits listed below, so don't miss out. Register online at www.philips.com/support to ensure: *Product safety notification By registering your product, you'll receive notification - directly from the manufacturer - in the rare case of a product recall or safety defect.
.English Important safety instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1 1. 12. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
.English 1 Notice Trademarks are the property of Koninklijke Philips N.V. or their respective owners. Funai Corporation reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this Owner’s manual is believed adequate for the intended use of the system. If the product or its individual modules or procedures are used for purposes other than those specified herein, confirmation of their validity and suitability must be obtained.
.English Positioning the TV Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Ɣ Large screen TVs are heavy. 2 people are required to carry and handle a large screen TV. Make sure to hold the upper and bottom frames of the unit firmly as illustrated. Install the unit in a horizontal and stable position. Do not install the unit in direct sunlight or in a place subject to dust or strong vibration. Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.
.English Copyright All other registered and unregistered trademarks are the property of their respective owners. The terms HDMI and HDMI HighDefinition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries. Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Audio, and the doubleD symbol are trademarks of Dolby Laboratories.
.English 2 Getting started Included accessories User manual Quick start guide Caution sheet CAUTIO THIS FI RS Ɣ N: READ Features DTV / Analog TV / CATV Ɣ T You can use your remote control to select channels which are broadcast in digital format and conventional analog format. Also, cable and satellite subscribers can access their TV channels. TV base and screws Information display You can display on the TV screen the title, contents (DTV only) and other information on the current program.
.English Unpacking 5 Support the top of the TV set with a hand to prevent the TV from falling. 6 Unhinge the retaining tabs and unfold the left and right side of the bottom packaging. It is recommended that two or more people remove the TV set from the box. Be careful not to injure your fingers and keep children away during assembly. (65PFL5903) 1 2 Open the top flaps of the box. Remove all accessories. Caution(s) Ɣ DO NOT take the TV set out of the box yet.
.English (55PFL5903, 50PFL5903) 1 Installing the stands Open the top flaps of the box. (65PFL5903) 1 Remove both of the bottom polystyrene foam bases. Carefully tear the plastic bag until the bottom corner of the TV is exposed. Ɣ 2 Support the top of the TV set at all times to prevent the TV from falling. Remove all accessories.
.English 5 Fasten the other stand to the TV with 2 screws (included). (55PFL5903, 50PFL5903) 1 Remove the tape on the bottom of the TV set and the plastic bag. 2 Fasten the matching stand to the TV with 2 screws (included). While fastening the screws, hold the stand to prevent it from falling. 2 screws required 6 Both stands should now be securely fastened.
.English Lifting the TV set Carefully lift the TV set as shown in the illustration and place it onto a stable, level surface. Removing cardboard Remove the cardboard attached to the screen. Installing the remote control batteries 1 2 3 Slide the battery cover off the back of the remote control. Insert the two included batteries (AAA, 1.5V). Be sure the + and – ends of the batteries line up with the markings inside the case. Slide the cover back into position.
.English Remote control a u (POWER) Turns the TV on from standby or off to standby. VUDU Access directly to VUDU. EasyLink buttons / : Searches backward or forward through the disc. : Starts, pauses or resumes playback. 1 b c s d e f r g t h i q j k p l o m n . : Stops the disc playback. Note(s) Ɣ Pause may not work properly on some devices even if they are EasyLink (HDMI CEC) compliant. YouTube Access directly to YouTube.
.English Control panel Terminals g b a m h f i j c d e Remote control sensor Receives IR signal from remote control. CH + / – Selects a channel. In the menu screen, moves the cursor up (+) / down (–). (POWER) Turns the TV on or switches the TV into standby mode. MENU Opens the main on-screen menu. SOURCE Selects connected devices. VOL + / – Adjusts the volume. In the menu screen, moves the cursor left (+) / right (–).
.English Connecting antenna or cable / satellite / IPTV set-top box Connecting a cable / satellite / IPTV set-top box, Bluray Disc™ / DVD recorder via composite connectors and analog audio Be sure your antenna or another device is connected properly before plugging in the AC power cord. Do not place your recorder too close to the screen because some recorders can be susceptible to harmful interference from the TV.
.English No included cables are used with these connections: Ɣ Connecting your devices Please purchase the necessary cables at your local store. Before you connect the AC power cord: Be sure other devices are connected properly before plugging in the AC power cord. Selecting your connection quality HDMI digital connection HDMI connection offers the highest picture quality.
.English HDMI-ARC connection Composite analog video connection HDMI-ARC allows you to use EasyLink to output TV audio directly to a connected audio device, without the need for an additional digital audio cable. Composite analog video connection offers standard picture quality for video devices connected to the unit. HDMI 2 IN only HDMI cable OUT If you connect to the unit’s component / composite video (Y/VIDEO) input jack (green), connect audio cables to the audio (L/R) input jacks.
.English Connecting the TV to the internet using a wireless LAN PC connection HDMI connection Internet This unit can be connected to your PC that has an HDMI terminal. Use an HDMI cable for this digital connection. Network provisioning equipment IN LAN OUT HDMI cable PC Ethernet cable HDMI-DVI connection WLAN Broadband router Note(s) Ɣ After you make the wireless connection, set up the necessary network settings. Connect to network p. 41 Ɣ Use a wireless LAN Access Point (AP) (e.g.
.English USB memory stick This unit offers easy playback of picture, music and video files. Insert the USB memory stick into the USB terminal shown below. For a complete list of file formats and specifications supported, refer to USB Section p. 27 Note(s) Ɣ The unit recognizes only a USB memory stick. Ɣ Do not use a USB hub or an extension cable to connect an external hard disk drive to the unit. (Not supported.) Ɣ Always insert a USB memory stick directly to this unit.
.English These operations are accessible by remote control. Some may also be accessible by the main unit's control panel. 5 Use Ɣ Initial setup This section will guide you through the unit’s Initial setting which includes selecting a language for your on-screen menu, country, location and Autoprogram, which automatically scans and memorizes viewable channels. You can also set the network connection in this setting. to select the signal type.
.English 7 Use to select your preferred picture setting, then press OK. After an initial setup is completed... Ɣ If you want to scan the channels automatically again. Search for channels p. 38 Ɣ If you want to change to another language. Language p. 34 Ɣ If you want to change the country setting. Country p. 51 Ɣ If you want to change the location setting. Location p. 35 Ɣ If you want to change the network setting. Connect to network p.
.English 3 Use your TV Switching channels TV Switching on your TV and putting it in standby mode Remote control TV Remote control To turn the TV on from standby or off to standby Press on the TV or the remote control. Ɣ Note(s) Ɣ Energy consumption contributes to air and water pollution. When the AC power cord is plugged in, your TV consumes energy with a very low standby power consumption. To select channels by using CH + / – Press CH + / – on the TV or the remote control.
.English Watching channels from an external device Switching each input mode can easily switch with the remote control between TV and external devices when they are connected to the unit. 1 Turn on the set-top box or the connected device. Lock or unlock your device from the Home menu This section describes how to lock or unlock specified device. 1 2 3 4 Press SOURCE on the remote control. Use Press OPTIONS on the remote control.
.English Create a list of favorite channels Changing picture format You can create lists of your preferred TV channels so that you can find those channels easily. Display modes can be selected when your TV receives a 16:9 or 4:3 video signal. Three types of display modes can be selected for a PC input signal. 1 2 Press OK while viewing a TV program. 3 Use to select the desired favorite list (Favorites 1 - Favorites 4), then press OK to add or remove on the list of favorite channels.
.English For 4:3 video signal TV screen information You can display the currently selected channel or other information such as the aspect ratio on the TV screen. Automatic Super zoom 4:3 In the digital mode, the detailed broadcasting information for the current off-the-air channel such as program title and program guides are displayed. 1 Manual Zoom Wide screen Press INFO.
.English Picture and sound Following settings can be configured. Using options menu You can access to some TV settings directly by using OPTIONS. 1 2 Auto picture To set predefined picture mode. Picture p. 31 Auto sound To set predefined sound mode. Sound p. 33 Headphone volume To adjust headphone volume. Sound p. 33 TV speakers To Select the audio output from the unit’s speakers or not. Sound p. 33 Picture format To switch the TV aspect ratio. Changing picture format p.
.English Note(s) USB Your TV is fitted with a USB connection that enables you to view photos, listen to music or watch video files stored on a USB memory stick. 1 2 Press SOURCE and use Use to select the desired file, then press OK. Photo USB DISK Ɣ to select USB, then press OK. Photo 2016_12_24 folder_A folder_B folder_C Ɣ This unit accepts USB memory stick only. Other storage devices such as external HDD by USB bus power will not work.
.English Viewing photos Playing music 1 2 3 1 2 3 Use to select Photo, then press OK. Use to select the desired item, then press OK. Press OK or 1 to start a slide show of the files. Use to select Music, then press OK. Use to select the desired item, then press OK. Press OK or 1 to play the selected files. Ɣ Press OK or 1 to pause the slide show. Ɣ Ɣ The 1 icon appears. Ɣ Ɣ Press or to move between images. Ɣ Press Ɣ Press BACK or . to stop the slide show.
.English Playing movies 1 2 3 Use to select Movie, then press OK. Use to select the desired item, then press OK. Press OK or 1 to play the selected files. Ɣ Press OK or 1 to pause, then press OK or 1 again to resume. Ɣ Press to fast-forward search. Ɣ Press Ɣ Press . to stop playback. Ɣ to fast-backward search. Press 1 to resume from the point at which playback was stopped. Press OK to play from the beginning of the file.
.English 4 Getting more from your TV Picture and sound setup This section describes the overview of the Setup menu displayed when you press and use to Select Setup. The Setup menu consists of the function setting items below. 1 p. 31 Guides you to get the best picture and sound settings. Press to display the Home menu. TV settings p. 31 Accesses menus that allow you to change picture, sound and TV usage settings. 2 Use to select Setup, then press OK.
.English Picture and sound setup Before you begin: You must set Home in Location. p. 35 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into standby mode. 1 2 3 Press and use Use to select Setup then press OK. to select Picture and sound setup, then press OK. Follow steps 7 to 8 in Initial setup p. 21 TV settings Picture Before you begin: You must set Home in Location. p.
.English You may adjust picture quality and enhancement settings using Pixel Precise Ultra HD and Advanced settings sub menus.
.English This selects sound modes for more spatial or surround sound reproduction. Sound You must set Home in Location. p. 35 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into standby mode. 1 2 3 Press and use Use Use to select Sound, then press OK. Picture Sound Features Installation Accessibility 4 Use OK. to select Setup then press OK. to select TV settings, then press OK.
.English Features 1 Press and use to select Setup then press OK. 2 Use to select TV settings, then press OK. 3 Use to select Features, then press OK. Picture Sound Features Installation Accessibility 4 Picture Sound Features Installation Accessibility Sleeptimer 4 Adjust the following items. Sleep timer can set the unit to go into standby mode after an incremental period of time. Use Language Preferences Restore default settings Adjust the following items.
.English TV placement Preferences You can set the unit to reduce the power consumption or adjust the backlight brightness in Location setting. EasyLink allows you to operate your connected EasyLink device. Setting your location to home Choosing Home gives you full flexibility to change predefined settings for picture and sound. 1 2 Use to select Preferences, then press OK. Use to select Location, then press OK.
.English EasyLink (HDMI CEC) Return your settings to default values This function allows you to operate the linked functions between our brand devices with a EasyLink feature and this unit connecting through an HDMI cable. You must connect this unit to our brand EasyLink devices and be sure its EasyLink (HDMI CEC) setting is also set to on. 1 2 3 Use to select Preferences, then press OK. Use to select EasyLink, then press OK. Use OK.
.English Caption settings Cable / NTSC (Analog) TV operation Closed captions displays the audio portion of the program as superimposed text over the video. 1 Use to select Caption settings, then press OK. Voice guide Off Closed captions Caption settings On Caption service Digital audio preferences Digital caption service CC w/ mute Digital caption options Caption service There are 3 display modes according to programs: Displays characters on the TV screen Paint-on immediately.
.English Digital audio preferences Channel settings You can set the interpretive broadcasting by an audio explanation. 1 Use to select Digital audio preferences, then press OK. Voice guide Audio accessibility Audio language Caption settings Digital audio preferences Primary audio selection criteria Audio accessibility Audio language Primary audio selection criteria 1 2 3 Press and use Use to select Channel settings, then press OK. Adjust the following items.
.English TV ratings lock Child lock You can prevent your children from watching certain programs or certain channels by locking the TV controls and by using ratings. 1 Use to select Child lock, then press OK.
.English US TV ratings TV-Y7 TV-PG TV-14 TV-MA Sub rating Fantasy Violence Violence Sex Language Dialog Violence Sex Language Change PIN Although the default PIN code (0000) is supplied with the unit, you can set your own PIN code. 1 2 3 Note(s) Blocked sub rating's will appear beside the main rating category in TV ratings lock menu. You cannot block a sub rating if the main rating is set to . Changing the category to / or automatically changes all its sub ratings to the (/ or ).
.English Connect to network Wireless setting Setup network connection settings in order to use Net TV or network upgrade functions. Select to use a wireless LAN to connect to the internet by a wireless connection. Ɣ Ɣ 1 2 The meanings of abbreviations are defined as below. : Wireless LAN access point AP : Wireless network name SSID The key entry screen will appear when you select SSID, WEP / others or proxy address. Use to select Wireless, then press OK.
.English Network settings 1 2 3 Press and use Use to select Setup then press OK. to select Network settings, then press OK. Adjust the following items. Manual network settings 1 Use to select Manual network settings, then press OK.
.English Manually enter your SSID Set up the connection to the AP (e.g. wireless router) manually by entering the SSID. 3 Use to select Manually enter your SSID, then press OK. AP (e.g. wireless router) SSID entry screen will appear. Enter the SSID using , then press OK. Use to select the authentication setting of the selected wireless network. Ɣ For a wireless network with authentication setting, select the authentication setting, according to the security type of the wireless network.
.English Proxy configuration 2 3 Use Use to select Proxy configuration, then press OK. to select a setting, then press OK. Network selection Proxy setting Wireless network setting Proxy address IP configuration Proxy port Proxy configuration Do not use Use Do not use is selected for default settings. If you need to change the proxy setting as instructed by your internet service provider to set the designated proxy address and port, select Use. Do not use Does not use the proxy server.
.English YouTube deactivation Home network You can turn your TV into a Digital Media Renderer (DMR), which can play video, music and photo files stored on certified home media servers connected to your home network. 1 2 Use to select Home network, then press OK. Use OK. to select the item you want to adjust, then press Off Renderer On Renderer name Displays the deactivation setting for YouTube. 1 2 3 4 Use to select Net TV, then press OK.
.English Update software USB upgrade Philips continuously tries to improve its products and we strongly recommend that you upgrade the TV software when upgrades are available. You can upgrade the software by using USB memory stick. 1 Connect your USB memory stick with the upgrade file to the USB terminal on the side of your TV. 2 3 4 5 6 Press and use New software can be downloaded from our website at www.philips.com/support using the model number of your TV to find information.
.English Network updates Software settings You can update the software by connecting the unit to the internet. 1 2 3 4 Press and use Use to select Update software, then press OK. Use Use to select Yes, then press OK. Ɣ 5 to select Setup then press OK. to select Network, then press OK. This unit will then start checking for the latest FirmWare (software) version. Confirmation message will appear.
.English Wireless screencasting You can wirelessly cast or mirror the screen of your Smartphone, Tablet or PC to the TV directly using wireless screencasting. Using wireless screencasting 1 Press and use to select Wireless Screencasting, then press OK. Ɣ Wireless screencasting mode screen appears. The TV is now ready to accept a connection from your source device.
.English Before using home network View your pictures using home network Follow the procedure below before using home network. 1 2 1 Connect this unit to the internet. Connecting the TV to the internet using an Ethernet cable p. 17 or Connecting the TV to the internet using a wireless LAN p. 18 Ɣ Broadband internet connection of 8Mbps or faster is required. 2 Ɣ Press BACK or . to stop the slide show. Ɣ Press OPTIONS to display the optional menu, then use to select the desired item.
.English Listen to music using home network Watch videos using home network 1 2 1 2 Press to select a file or a folder. Press OK or 1 to play the selected files. Press OK or 1 to pause, press OK or 1 again to resume. Ɣ Press / to skip up the next file. Ɣ Press 0 to skip down the previous file. Ɣ Press . to stop playback. Ɣ Press OPTIONS to display the optional menu, then use to select the desired item. Off Sets Voice guide to off. Voice guide toggle * On Sets Voice guide to on.
.English My Apps functions Net TV Net TV offers internet services for your TV. Use the TV remote control to browse the Net TV pages. You can play movies, listen to music and much more, all from your TV screen. – Because Net TV is an online system, it can be modified over time to better serve its purpose. – Some Net TV services can be added, changed or stopped after some time. – You cannot download and save files or install plug-ins.
.English Changing picture settings during playback Using Vewd browser 1 Press OPTIONS and use OK. The Vewd browser allows you to surf the Internet on your TV and provides quick access to the search engine. 2 3 Use to select Picture, then press OK. Use to select the item you want to adjust, then press OK. Ɣ to select TV settings, then press 1 For more details, refer to Picture p. 31 Press NETTV, then use to select the Vewd browser icon in Featured Apps, then press OK.
.English Pandora operations With this unit, you can instantly listen to personalized radio stations streamed over the internet from Pandora. To learn more about Pandora, please visit www.pandora.com Creating a new station By entering your favorite artists or tracks, Pandora selects music and creates a new station for you on the basis of the entered information. 1 On the station list screen, Use then press OK. 2 Enter a name of your favorite artist or tracks, then press OK while OK is selected.
.English 5 Useful tips FAQ Question My remote control does not work.
.English Troubleshooting tips If the unit does not perform properly when operated as instructed in this manual, Please check the following Troubleshooting tips and all connections once before calling for service. Power No power Ɣ Make sure the AC power cord is plugged in. Ɣ Make sure that the AC outlet supplies the proper voltage, plug another electrical appliance into the AC outlet to ensure that the AC outlet operates normally.
.English Closed captions Closed captions are displayed as a white box. No closed captions are displayed in the closed captions-supported program. Ɣ Interference from buildings or weather conditions may cause closed captions to be incomplete if watching analog TV signals. Ɣ Broadcasting station may shorten the program to insert advertisements. The closed caption decoder cannot read the information of the shortened program. Black box is displayed on the TV screen. Ɣ The text mode is selected for caption.
.English 6 Information Glossary Analog TV (NTSC) Acronym that stands for National Television Systems Committee and the name of analog broadcasting standards. Off the air analog TV signals are no longer being sent by major broadcasting stations in the USA. ARC (Audio Return Channel) (HDMI 2 only) HDMI-ARC allows you to use Philips EasyLink to output TV audio directly to a connected audio device, without the need for an additional digital audio cable.
.English 7 Specifications Model # 65PFL5903 55PFL5903 50PFL5903 Picture Type UHD (Ultra HD) (3840 x 2160 pixels 60Hz) Diagonal screen size / Aspect ratio 64.5”/ 16:9 Viewing angles 178° (V) by 178° (H) Built-in digital / analog tuner ATSC (digital) / NTSC (analog) 54.6”/ 16:9 49.
.English 8 Warranty LIMITED WARRANTY ONE (1) YEAR WARRANTY COVERAGE: This warranty obligation is limited to the terms as set forth below. WHO IS COVERED: This product warranty is issued to the original purchaser or the person receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer.
.English License Funai Corporation, Inc. hereby offers to deliver, upon request, a copy of the complete corresponding source code for the copyrighted open source code packages, on an “AS IS” basis, used in this product for which such offer is requested by the respective licenses. This offer is valid up to three years after the product purchase to anyone in receipt of this information. To obtain source code, please contact Funai Corporation, Inc.
Funai Corporation, Inc. 21061 S. Western Ave. Suite 210, Torrance, CA 90501, USA P&F Mexicana, S.A. de C.V. Av. La Palma No. 6, Col. San Fernando La Herradura. Huixquilucan, Edo. de México. C.P. 52787 This product has been manufactured by and is sold under the responsibility of Funai Corporation, Inc., and Funai Corporation, Inc. is the warrantor in relation to this product. The Philips trademark and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. used under license.