English A Introduction This dual VGA, VA plus color monitor displays sharp images of text and graphics with a maximum resolution up to 1024x768 pixels by interlaced {(XGA) mode. This monitor automatically scans vertical frequencies between 50 Hz and 100 Hz. You may use this color monitor with a computer which utilizes IBM PC, PCT, PG/AT, PS/2 or either compatible system that is fetid with a VGA interface card.
M‘ Safety precautions and maintenance # Disconnect the monitor from the mains supply i the monitor is not to be used for an extended period of time. 4 Do not attempt to remove the hack cover, as you will be exposed to a shock hazard. The back cover should only be removed by qualified service personnel. 4 Do not place abject on top of the monitor cabinet, which could fall into vents or which could cover them and prevent proper cooling of the monitor's electronics.
Installation NOTE: Before installing this monitor, please refer to the user's guides of your computer and video adapter to make sure if these equipment require any change of sating. Pasitioning/Ventilation WARNING: WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCESSIBLE. Do not place the monitor near a heat source. T prevent overheating, ensure that the ventilation openings of the monitor are nat covered.
0 Connection to the computer NOTE: Please be sure the AC power to your computer is “OFF” before connecting or disconnecting any display peripheral. Failure to do so may cause serious personal injury as well as permanent damage to your computer equipment. {BM PC, PCT, PC/AT, PS/2, or the compatibles: & Connect the fixed 15-pin D-sub connector of the video signal cable to the computer at the video connector on the video card, and fix it firmly with the screws on the plug.
Connection to the mains (Roar of tho monitors) {trains cord Connecting to the mains This monitor is set to operate at a mains supply of 100-240 volts AG. if the mains voltage in your home is not between this, consult your dealer.
Adjustment For an optimized adjustment of the picture following controls are available at the front. (@ POWER ® Press this knob, the green LED lights and power is ON. ® Press this knob again, the green LED disappears and the power is OFF, ® The green LED will flash when the power management system has been activated. CONT. & Used to adjust contrast. 0 BRIGHT. # Sad to adjust brightness, H-SIZE ® Used to adjust image width. (D SHIFT ® Used to adjust image position horizontally.
Adjustment The monitor is per-set on 800x600 mode as default SAGA Mode. For an affirmative mode, 1.6, 1024x768, the following controls are available at the rear to optimize adjustment of the picture: (The default mode wil be replaced by re-adjust per-set) H-SIZE ® Used to adjust image width. (D H-SHIFT ® Used to adjust image position horizontally. @ v-size ® Used to adjust image height., & v-shift ® Used fo adjust image position vertically.
M Technical information () General: Picture tube Screen area + 14 inch, 90° defection, non-glare, black matrix, light transmission P22 medium short, dotted pitch 0.28 mm. © 250 mm (H) x 188 mm (V) Line (Horizontal} frequency : KHz Raster (Vertical) frequency : 50100 Hz {automatically) Mains voltage : Power consumption Dot rate Pedestal : 100-240 VAC, 60-50 HZ : 80 Walt max. 1 35 MHz © Ti kt 5° forward, 15> backward; swivel 90° left or right.
(IV}Pin assignment: The 15-pin D-sub connector {male) of the signal cable (IBM systems): Pin No. | Assignment Pin No. | Assignment 1 Red dived input 8 No pin 2 Green video input 10 Logic ground 3 Blue video input 11 identical cutout 4 identical output connected to pin 10 Connected to pin 10 12 No pin 5 Self-test input 13 H. Sync 8 Red video ground 14 V.
